summaryrefslogtreecommitdiffstats
path: root/keyboards/handwired
diff options
context:
space:
mode:
Diffstat (limited to 'keyboards/handwired')
-rw-r--r--keyboards/handwired/onekey/bluepill/boards/GENERIC_STM32_F103/board.c56
-rw-r--r--keyboards/handwired/onekey/bluepill/boards/GENERIC_STM32_F103/board.h166
-rw-r--r--keyboards/handwired/onekey/bluepill/boards/GENERIC_STM32_F103/board.mk5
3 files changed, 0 insertions, 227 deletions
diff --git a/keyboards/handwired/onekey/bluepill/boards/GENERIC_STM32_F103/board.c b/keyboards/handwired/onekey/bluepill/boards/GENERIC_STM32_F103/board.c
deleted file mode 100644
index 8c5a87f35f..0000000000
--- a/keyboards/handwired/onekey/bluepill/boards/GENERIC_STM32_F103/board.c
+++ /dev/null
@@ -1,56 +0,0 @@
-/*
- ChibiOS - Copyright (C) 2006..2015 Giovanni Di Sirio
-
- Licensed under the Apache License, Version 2.0 (the "License");
- you may not use this file except in compliance with the License.
- You may obtain a copy of the License at
-
- http://www.apache.org/licenses/LICENSE-2.0
-
- Unless required by applicable law or agreed to in writing, software
- distributed under the License is distributed on an "AS IS" BASIS,
- WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
- See the License for the specific language governing permissions and
- limitations under the License.
-*/
-
-#include "hal.h"
-
-// Value to place in RTC backup register 10 for persistent bootloader mode
-#define RTC_BOOTLOADER_FLAG 0x424C
-
-/**
- * @brief PAL setup.
- * @details Digital I/O ports static configuration as defined in @p board.h.
- * This variable is used by the HAL when initializing the PAL driver.
- */
-#if HAL_USE_PAL || defined(__DOXYGEN__)
-const PALConfig pal_default_config =
-{
- {VAL_GPIOAODR, VAL_GPIOACRL, VAL_GPIOACRH},
- {VAL_GPIOBODR, VAL_GPIOBCRL, VAL_GPIOBCRH},
- {VAL_GPIOCODR, VAL_GPIOCCRL, VAL_GPIOCCRH},
- {VAL_GPIODODR, VAL_GPIODCRL, VAL_GPIODCRH},
- {VAL_GPIOEODR, VAL_GPIOECRL, VAL_GPIOECRH},
-};
-#endif
-
-/*
- * Early initialization code.
- * This initialization must be performed just after stack setup and before
- * any other initialization.
- */
-void __early_init(void) {
-
- stm32_clock_init();
-}
-
-/*
- * Board-specific initialization code.
- */
-void boardInit(void) {
- //JTAG-DP Disabled and SW-DP Enabled
- AFIO->MAPR |= AFIO_MAPR_SWJ_CFG_JTAGDISABLE;
- //Set backup register DR10 to enter bootloader on reset
- BKP->DR10 = RTC_BOOTLOADER_FLAG;
-}
diff --git a/keyboards/handwired/onekey/bluepill/boards/GENERIC_STM32_F103/board.h b/keyboards/handwired/onekey/bluepill/boards/GENERIC_STM32_F103/board.h
deleted file mode 100644
index 9427adabf1..0000000000
--- a/keyboards/handwired/onekey/bluepill/boards/GENERIC_STM32_F103/board.h
+++ /dev/null
@@ -1,166 +0,0 @@
-/*
- ChibiOS - Copyright (C) 2006..2015 Giovanni Di Sirio
-
- Licensed under the Apache License, Version 2.0 (the "License");
- you may not use this file except in compliance with the License.
- You may obtain a copy of the License at
-
- http://www.apache.org/licenses/LICENSE-2.0
-
- Unless required by applicable law or agreed to in writing, software
- distributed under the License is distributed on an "AS IS" BASIS,
- WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
- See the License for the specific language governing permissions and
- limitations under the License.
-*/
-
-#ifndef _BOARD_H_
-#define _BOARD_H_
-
-/*
- * Setup for a Generic STM32F103 board.
- */
-
-/*
- * Board identifier.
- */
-#define BOARD_GENERIC_STM32_F103
-#define BOARD_NAME "Generic STM32F103x board"
-
-/*
- * Board frequencies.
- */
-#define STM32_LSECLK 32768
-#define STM32_HSECLK 8000000
-
-/*
- * MCU type, supported types are defined in ./os/hal/platforms/hal_lld.h.
- */
-#define STM32F103xB
-
-/*
- * IO pins assignments
- */
-
-/* on-board */
-
-#define GPIOA_LED 8
-#define GPIOD_OSC_IN 0
-#define GPIOD_OSC_OUT 1
-
-/* In case your board has a "USB enable" hardware
- controlled by a pin, define it here. (It could be just
- a 1.5k resistor connected to D+ line.)
-*/
-/*
-#define GPIOB_USB_DISC 10
-*/
-
-/*
- * I/O ports initial setup, this configuration is established soon after reset
- * in the initialization code.
- *
- * The digits have the following meaning:
- * 0 - Analog input.
- * 1 - Push Pull output 10MHz.
- * 2 - Push Pull output 2MHz.
- * 3 - Push Pull output 50MHz.
- * 4 - Digital input.
- * 5 - Open Drain output 10MHz.
- * 6 - Open Drain output 2MHz.
- * 7 - Open Drain output 50MHz.
- * 8 - Digital input with PullUp or PullDown resistor depending on ODR.
- * 9 - Alternate Push Pull output 10MHz.
- * A - Alternate Push Pull output 2MHz.
- * B - Alternate Push Pull output 50MHz.
- * C - Reserved.
- * D - Alternate Open Drain output 10MHz.
- * E - Alternate Open Drain output 2MHz.
- * F - Alternate Open Drain output 50MHz.
- * Please refer to the STM32 Reference Manual for details.
- */
-
-/*
- * Port A setup.
- * Everything input with pull-up except:
- * PA2 - Alternate output (USART2 TX).
- * PA3 - Normal input (USART2 RX).
- * PA9 - Alternate output (USART1 TX).
- * PA10 - Normal input (USART1 RX).
- */
-#define VAL_GPIOACRL 0x88884B88 /* PA7...PA0 */
-#define VAL_GPIOACRH 0x888884B8 /* PA15...PA8 */
-#define VAL_GPIOAODR 0xFFFFFFFF
-
-/*
- * Port B setup.
- * Everything input with pull-up except:
- * PB10 - Push Pull output (USB switch).
- */
-#define VAL_GPIOBCRL 0x88888888 /* PB7...PB0 */
-#define VAL_GPIOBCRH 0x88888388 /* PB15...PB8 */
-#define VAL_GPIOBODR 0xFFFFFFFF
-
-/*
- * Port C setup.
- * Everything input with pull-up except:
- * PC13 - Push Pull output (LED).
- */
-#define VAL_GPIOCCRL 0x88888888 /* PC7...PC0 */
-#define VAL_GPIOCCRH 0x88388888 /* PC15...PC8 */
-#define VAL_GPIOCODR 0xFFFFFFFF
-
-/*
- * Port D setup.
- * Everything input with pull-up except:
- * PD0 - Normal input (XTAL).
- * PD1 - Normal input (XTAL).
- */
-#define VAL_GPIODCRL 0x88888844 /* PD7...PD0 */
-#define VAL_GPIODCRH 0x88888888 /* PD15...PD8 */
-#define VAL_GPIODODR 0xFFFFFFFF
-
-/*
- * Port E setup.
- * Everything input with pull-up except:
- */
-#define VAL_GPIOECRL 0x88888888 /* PE7...PE0 */
-#define VAL_GPIOECRH 0x88888888 /* PE15...PE8 */
-#define VAL_GPIOEODR 0xFFFFFFFF
-
-/*
- * USB bus activation macro, required by the USB driver.
- */
-/* The point is that most of the generic STM32F103* boards
- have a 1.5k resistor connected on one end to the D+ line
- and on the other end to some pin. Or even a slightly more
- complicated "USB enable" circuit, controlled by a pin.
- That should go here.
-
- However on some boards (e.g. one that I have), there's no
- such hardware. In which case it's better to not do anything.
-*/
-/*
-#define usb_lld_connect_bus(usbp) palClearPad(GPIOB, GPIOB_USB_DISC)
-*/
-#define usb_lld_connect_bus(usbp) palSetPadMode(GPIOA, 12, PAL_MODE_INPUT);
-
-/*
- * USB bus de-activation macro, required by the USB driver.
- */
-/*
-#define usb_lld_disconnect_bus(usbp) palSetPad(GPIOB, GPIOB_USB_DISC)
-*/
-#define usb_lld_disconnect_bus(usbp) palSetPadMode(GPIOA, 12, PAL_MODE_OUTPUT_PUSHPULL); palClearPad(GPIOA, 12);
-
-#if !defined(_FROM_ASM_)
-#ifdef __cplusplus
-extern "C" {
-#endif
- void boardInit(void);
-#ifdef __cplusplus
-}
-#endif
-#endif /* _FROM_ASM_ */
-
-#endif /* _BOARD_H_ */
diff --git a/keyboards/handwired/onekey/bluepill/boards/GENERIC_STM32_F103/board.mk b/keyboards/handwired/onekey/bluepill/boards/GENERIC_STM32_F103/board.mk
deleted file mode 100644
index 6b8b312fd9..0000000000
--- a/keyboards/handwired/onekey/bluepill/boards/GENERIC_STM32_F103/board.mk
+++ /dev/null
@@ -1,5 +0,0 @@
-# List of all the board related files.
-BOARDSRC = $(BOARD_PATH)/boards/GENERIC_STM32_F103/board.c
-
-# Required include directories
-BOARDINC = $(BOARD_PATH)/boards/GENERIC_STM32_F103