diff options
Diffstat (limited to 'keyboards/handwired')
| -rw-r--r-- | keyboards/handwired/CMD60/CMD60.c | 8 | ||||
| -rw-r--r-- | keyboards/handwired/CMD60/CMD60.h | 20 | ||||
| -rw-r--r-- | keyboards/handwired/CMD60/Makefile | 73 | ||||
| -rw-r--r-- | keyboards/handwired/CMD60/README.md | 35 | ||||
| -rw-r--r-- | keyboards/handwired/CMD60/config.h | 162 | ||||
| -rw-r--r-- | keyboards/handwired/CMD60/keymaps/default/keymap.c | 66 | ||||
| -rw-r--r-- | keyboards/handwired/traveller/Makefile | 89 | ||||
| -rw-r--r-- | keyboards/handwired/traveller/config.h | 173 | ||||
| -rw-r--r-- | keyboards/handwired/traveller/keymaps/default/keymap.c | 305 | ||||
| -rw-r--r-- | keyboards/handwired/traveller/keymaps/default/readme.md | 2 | ||||
| -rw-r--r-- | keyboards/handwired/traveller/readme.md | 35 | ||||
| -rw-r--r-- | keyboards/handwired/traveller/traveller.c | 61 | ||||
| -rw-r--r-- | keyboards/handwired/traveller/traveller.h | 32 |
13 files changed, 1061 insertions, 0 deletions
diff --git a/keyboards/handwired/CMD60/CMD60.c b/keyboards/handwired/CMD60/CMD60.c new file mode 100644 index 0000000000..799848e34e --- /dev/null +++ b/keyboards/handwired/CMD60/CMD60.c @@ -0,0 +1,8 @@ +#include "CMD60.h" + +void matrix_init_kb(void) { + // put your keyboard start-up code here + // runs once when the firmware starts up + + matrix_init_user(); +} diff --git a/keyboards/handwired/CMD60/CMD60.h b/keyboards/handwired/CMD60/CMD60.h new file mode 100644 index 0000000000..f90871fc71 --- /dev/null +++ b/keyboards/handwired/CMD60/CMD60.h @@ -0,0 +1,20 @@ +#ifndef CMD60_H +#define CMD60_H + +#include "quantum.h" + +#define KEYMAP( \ + K00, K01, K02, K03, K04, K05, K06, K07, K08, K09, K0A, K0B, K0C, K0D, \ + K10, K11, K12, K13, K14, K15, K16, K17, K18, K19, K1A, K1B, K1C, K1D, \ + K20, K21, K22, K23, K24, K25, K26, K27, K28, K29, K2A, K2B, K2C, K2D, \ + K30, K31, K32, K33, K34, K35, K36, K37, K38, K39, K3A, K3B, K3C, K3D, \ + K40, K41, K42, K45, K4A, K4B, K4C, K4D \ + ) { \ + { K00, K01, K02, K03, K04, K05, K06, K07, K08, K09, K0A, K0B, K0C, K0D }, \ + { K10, K11, K12, K13, K14, K15, K16, K17, K18, K19, K1A, K1B, K1C, K1D }, \ + { K20, K21, K22, K23, K24, K25, K26, K27, K28, K29, K2A, K2B, K2C, K2D }, \ + { K30, K31, K32, K33, K34, K35, K36, K37, K38, K39, K3A, K3B, K3C, K3D }, \ + { K40, K41, K42, KC_NO, KC_NO, K45, KC_NO, KC_NO, KC_NO, KC_NO,K4A, K4B, K4C, K4D } \ +} + +#endif
\ No newline at end of file diff --git a/keyboards/handwired/CMD60/Makefile b/keyboards/handwired/CMD60/Makefile new file mode 100644 index 0000000000..7117599173 --- /dev/null +++ b/keyboards/handwired/CMD60/Makefile @@ -0,0 +1,73 @@ + +# MCU name +MCU = atmega32u4 + +# Processor frequency. +# This will define a symbol, F_CPU, in all source code files equal to the +# processor frequency in Hz. You can then use this symbol in your source code to +# calculate timings. Do NOT tack on a 'UL' at the end, this will be done +# automatically to create a 32-bit value in your source code. +# +# This will be an integer division of F_USB below, as it is sourced by +# F_USB after it has run through any CPU prescalers. Note that this value +# does not *change* the processor frequency - it should merely be updated to +# reflect the processor speed set externally so that the code can use accurate +# software delays. +F_CPU = 16000000 + + +# +# LUFA specific +# +# Target architecture (see library "Board Types" documentation). +ARCH = AVR8 + +# Input clock frequency. +# This will define a symbol, F_USB, in all source code files equal to the +# input clock frequency (before any prescaling is performed) in Hz. This value may +# differ from F_CPU if prescaling is used on the latter, and is required as the +# raw input clock is fed directly to the PLL sections of the AVR for high speed +# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' +# at the end, this will be done automatically to create a 32-bit value in your +# source code. +# +# If no clock division is performed on the input clock inside the AVR (via the +# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. +F_USB = $(F_CPU) + +# Interrupt driven control endpoint task(+60) +OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT + + +# Boot Section Size in *bytes* +# Teensy halfKay 512 +# Teensy++ halfKay 1024 +# Atmel DFU loader 4096 +# LUFA bootloader 4096 +# USBaspLoader 2048 +OPT_DEFS += -DBOOTLOADER_SIZE=512 + + +# Build Options +# change yes to no to disable +# +BOOTMAGIC_ENABLE ?= no # Virtual DIP switch configuration(+1000) +MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700) +EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) +CONSOLE_ENABLE ?= yes # Console for debug(+400) +COMMAND_ENABLE ?= yes # Commands for debug and configuration +# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE +SLEEP_LED_ENABLE ?= no # Breathing sleep LED during USB suspend +# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work +NKRO_ENABLE ?= no # USB Nkey Rollover +BACKLIGHT_ENABLE ?= no # Enable keyboard backlight functionality on B7 by default +MIDI_ENABLE ?= no # MIDI controls +UNICODE_ENABLE ?= no # Unicode +BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID +AUDIO_ENABLE ?= no # Audio output on port C6 + +ifndef QUANTUM_DIR + include ../../../Makefile +endif + + diff --git a/keyboards/handwired/CMD60/README.md b/keyboards/handwired/CMD60/README.md new file mode 100644 index 0000000000..83e371543e --- /dev/null +++ b/keyboards/handwired/CMD60/README.md @@ -0,0 +1,35 @@ +CMD60 keyboard firmware +====================== + +##CMD60 + +This layout has been designed to optimize use of the left-hand, and it focussed specifically on programmers who work +with text editors like SublimeText and Atom. It utilizes the power of Space_fn, and features a caps lock swap for Fn2 +and enter key on tap. These features allow you to keep your right hand on the mouse more and should enable you to +achieve a higher level of productivity if you take the time to learn its function layers. + +## Quantum MK Firmware + +For the full Quantum feature list, see [the parent readme.md](/doc/readme.md). + +## Building + +Download or clone the whole firmware and navigate to the keyboards/handwired/CMD60 folder. +Once your dev env is setup, you'll be able to type `make` to generate your .hex - you can then use +the Teensy Loader to program your .hex file. + +Depending on which keymap you would like to use, you will have to compile slightly differently. + +### Default + +To build with the default keymap, simply run `make`. + +### Other Keymaps + +To build the firmware binary hex file with a keymap just do `make` with `keymap` option like: + +``` +$ make keymap=[default|jack|<name>] +``` + +Keymaps follow the format **__keymap.c__** and are stored in folders in the `keymaps` folder, eg `keymaps/my_keymap/` diff --git a/keyboards/handwired/CMD60/config.h b/keyboards/handwired/CMD60/config.h new file mode 100644 index 0000000000..27eb400b87 --- /dev/null +++ b/keyboards/handwired/CMD60/config.h @@ -0,0 +1,162 @@ +/* +Copyright 2012 Jun Wako <wakojun@gmail.com> + +This program is free software: you can redistribute it and/or modify +it under the terms of the GNU General Public License as published by +the Free Software Foundation, either version 2 of the License, or +(at your option) any later version. + +This program is distributed in the hope that it will be useful, +but WITHOUT ANY WARRANTY; without even the implied warranty of +MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +GNU General Public License for more details. + +You should have received a copy of the GNU General Public License +along with this program. If not, see <http://www.gnu.org/licenses/>. +*/ + +#ifndef CONFIG_H +#define CONFIG_H + +#include "config_common.h" + +/* USB Device descriptor parameter */ +#define VENDOR_ID 0xFEED +#define PRODUCT_ID 0x6060 +#define DEVICE_VER 0x0001 +#define MANUFACTURER cmd +#define PRODUCT CMD60 +#define DESCRIPTION Advanced Programming Keeb Layout + +/* key matrix size */ +#define MATRIX_ROWS 5 +#define MATRIX_COLS 14 + +/* + * Keyboard Matrix Assignments + * + * Change this to how you wired your keyboard + * COLS: AVR pins used for columns, left to right + * ROWS: AVR pins used for rows, top to bottom + * DIODE_DIRECTION: COL2ROW = COL = Anode (+), ROW = Cathode (-, marked on diode) + * ROW2COL = ROW = Anode (+), COL = Cathode (-, marked on diode) + * +*/ +#define MATRIX_ROW_PINS { F0, F4, F5, F6, F7 } +#define MATRIX_COL_PINS { B0, B1, B2, B3, B7, D0, D1, D2, D3, C6, D7, B4, B5, B6 } +#define UNUSED_PINS + +/* COL2ROW or ROW2COL */ +#define DIODE_DIRECTION COL2ROW + +// #define BACKLIGHT_PIN B7 +// #define BACKLIGHT_BREATHING +// #define BACKLIGHT_LEVELS 3 + + +/* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */ +#define DEBOUNCING_DELAY 5 + +/* define if matrix has ghost (lacks anti-ghosting diodes) */ +//#define MATRIX_HAS_GHOST + +/* number of backlight levels */ + +/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */ +#define LOCKING_SUPPORT_ENABLE +/* Locking resynchronize hack */ +#define LOCKING_RESYNC_ENABLE + +/* + * Force NKRO + * + * Force NKRO (nKey Rollover) to be enabled by default, regardless of the saved + * state in the bootmagic EEPROM settings. (Note that NKRO must be enabled in the + * makefile for this to work.) + * + * If forced on, NKRO can be disabled via magic key (default = LShift+RShift+N) + * until the next keyboard reset. + * + * NKRO may prevent your keystrokes from being detected in the BIOS, but it is + * fully operational during normal computer usage. + * + * For a less heavy-handed approach, enable NKRO via magic key (LShift+RShift+N) + * or via bootmagic (hold SPACE+N while plugging in the keyboard). Once set by + * bootmagic, NKRO mode will always be enabled until it is toggled again during a + * power-up. + * + */ +//#define FORCE_NKRO + +/* + * Magic Key Options + * + * Magic keys are hotkey commands that allow control over firmware functions of + * the keyboard. They are best used in combination with the HID Listen program, + * found here: https://www.pjrc.com/teensy/hid_listen.html + * + * The options below allow the magic key functionality to be changed. This is + * useful if your keyboard/keypad is missing keys and you want magic key support. + * + */ + +/* key combination for magic key command */ +#define IS_COMMAND() ( \ + keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)) \ +) + +/* control how magic key switches layers */ +//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS true +//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS true +//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM false + +/* override magic key keymap */ +//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS +//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS +//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM +//#define MAGIC_KEY_HELP1 H +//#define MAGIC_KEY_HELP2 SLASH +//#define MAGIC_KEY_DEBUG D +//#define MAGIC_KEY_DEBUG_MATRIX X +//#define MAGIC_KEY_DEBUG_KBD K +//#define MAGIC_KEY_DEBUG_MOUSE M +//#define MAGIC_KEY_VERSION V +//#define MAGIC_KEY_STATUS S +//#define MAGIC_KEY_CONSOLE C +//#define MAGIC_KEY_LAYER0_ALT1 ESC +//#define MAGIC_KEY_LAYER0_ALT2 GRAVE +//#define MAGIC_KEY_LAYER0 0 +//#define MAGIC_KEY_LAYER1 1 +//#define MAGIC_KEY_LAYER2 2 +//#define MAGIC_KEY_LAYER3 3 +//#define MAGIC_KEY_LAYER4 4 +//#define MAGIC_KEY_LAYER5 5 +//#define MAGIC_KEY_LAYER6 6 +//#define MAGIC_KEY_LAYER7 7 +//#define MAGIC_KEY_LAYER8 8 +//#define MAGIC_KEY_LAYER9 9 +//#define MAGIC_KEY_BOOTLOADER PAUSE +//#define MAGIC_KEY_LOCK CAPS +//#define MAGIC_KEY_EEPROM E +//#define MAGIC_KEY_NKRO N +//#define MAGIC_KEY_SLEEP_LED Z + +/* + * Feature disable options + * These options are also useful to firmware size reduction. + */ + +/* disable debug print */ +//#define NO_DEBUG + +/* disable print */ +//#define NO_PRINT + +/* disable action features */ +//#define NO_ACTION_LAYER +//#define NO_ACTION_TAPPING +//#define NO_ACTION_ONESHOT +//#define NO_ACTION_MACRO +//#define NO_ACTION_FUNCTION + +#endif diff --git a/keyboards/handwired/CMD60/keymaps/default/keymap.c b/keyboards/handwired/CMD60/keymaps/default/keymap.c new file mode 100644 index 0000000000..9f9cbcd661 --- /dev/null +++ b/keyboards/handwired/CMD60/keymaps/default/keymap.c @@ -0,0 +1,66 @@ +#include "CMD60.h" + +const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { + [0] = KEYMAP( /* CMD60 - QWERTY */ + KC_ESC, KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_MINS, KC_EQL, KC_BSPC, \ + KC_TAB, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_LBRC, KC_RBRC, KC_BSLS, \ + LT(3, KC_ENT), KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, KC_SCLN, KC_QUOT, KC_NO, KC_ENT, \ + KC_LSFT, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_N, KC_M, KC_COMM, KC_DOT, KC_SLSH, KC_NO, KC_NO, KC_RSFT, \ + KC_LCTL, KC_LGUI, KC_LALT, LT(2, KC_SPC), MO(3), MO(4), MO(5), TG(1) \ + ), + [1] = KEYMAP( /* CMD60 - GameMode */ + KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, \ + KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, \ + KC_CAPS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_NO, KC_TRNS, \ + KC_LSFT, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_NO, KC_NO, KC_RSFT, \ + KC_TRNS, KC_NO, KC_TRNS, KC_SPC, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS \ + ), + [2] = KEYMAP( /* CMD60 - Arrows */ + KC_GRV, KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_F7, KC_F8, KC_F9, KC_F10, KC_F11, KC_F12, KC_DEL, \ + KC_TRNS, KC_BSPC, KC_UP, KC_DEL, KC_TRNS, KC_TRNS, KC_TRNS, KC_BSPC, KC_UP, KC_DEL, KC_PSCR, KC_SLCK, KC_PAUS, KC_TRNS, \ + KC_TRNS, KC_LEFT, KC_DOWN, KC_RIGHT, KC_TRNS, KC_TRNS, KC_TRNS, KC_LEFT, KC_DOWN, KC_RIGHT, KC_TRNS, KC_TRNS, KC_NO, KC_TRNS, \ + KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_SPC, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_NO, KC_NO, KC_TRNS, \ + KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS \ + ), + [3] = KEYMAP( /* CMD60 - Functions */ + KC_GRV, KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_F7, KC_F8, KC_F9, KC_F10, KC_F11, KC_F12, KC_DEL, \ + KC_AUDIO_MUTE, KC_BSPC, KC_PGUP, KC_DEL, KC_TRNS, KC_TRNS, KC_TRNS, KC_PGUP, KC_UP, KC_PGDN, KC_TRNS, KC_PAUSE, KC_SLCK, KC_PSCREEN, \ + KC_TRNS, KC_HOME, KC_PGDN, KC_END, KC_TRNS, KC_TRNS, KC_HOME, KC_LEFT, KC_DOWN, KC_RIGHT, KC_TRNS, KC_INSERT, KC_NO, KC_TRNS, \ + KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_END, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_NO, KC_NO, KC_TRNS, \ + KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS \ + ), + [4] = KEYMAP( /* CMD60 - Mouse */ + KC_SYSTEM_SLEEP, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, \ + KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_MS_BTN1, KC_MS_UP, KC_MS_BTN2, KC_TRNS, KC_TRNS, KC_TRNS, \ + KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_MS_LEFT, KC_MS_DOWN, KC_MS_RIGHT, KC_TRNS, KC_NO, KC_TRNS, \ + KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_MS_WH_UP, KC_MS_BTN3, KC_MS_WH_DOWN, KC_NO, KC_NO, KC_TRNS, \ + KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS \ + ), + [5] = KEYMAP( /* CMD60 - Media */ + KC_SYSTEM_WAKE, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, \ + KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_AUDIO_VOL_DOWN, KC_AUDIO_VOL_UP, KC_AUDIO_MUTE, \ + KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_MEDIA_PREV_TRACK, KC_MEDIA_NEXT_TRACK, KC_MEDIA_PLAY_PAUSE, \ + KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_WWW_BACK, KC_WWW_FORWARD, KC_NO, KC_NO, KC_WWW_REFRESH, \ + KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS \ + ), +}; + +const uint16_t PROGMEM fn_actions[] = { + +}; + + +const macro_t *action_get_macro(keyrecord_t *record, uint8_t id, uint8_t opt) +{ + // MACRODOWN only works in this function + switch(id) { + case 0: + if (record->event.pressed) { + register_code(KC_RSFT); + } else { + unregister_code(KC_RSFT); + } + break; + } + return MACRO_NONE; +}; diff --git a/keyboards/handwired/traveller/Makefile b/keyboards/handwired/traveller/Makefile new file mode 100644 index 0000000000..12a4b71f4e --- /dev/null +++ b/keyboards/handwired/traveller/Makefile @@ -0,0 +1,89 @@ + +#MCU = at90usb1287 +MCU = atmega32u4 + +# Processor frequency. +# This will define a symbol, F_CPU, in all source code files equal to the +# processor frequency in Hz. You can then use this symbol in your source code to +# calculate timings. Do NOT tack on a 'UL' at the end, this will be done +# automatically to create a 32-bit value in your source code. +# +# This will be an integer division of F_USB below, as it is sourced by +# F_USB after it has run through any CPU prescalers. Note that this value +# does not *change* the processor frequency - it should merely be updated to +# reflect the processor speed set externally so that the code can use accurate +# software delays. +F_CPU = 16000000 + +# for avr upload +USB ?= /dev/cu.usbmodem1421 +# +# LUFA specific +# +# Target architecture (see library "Board Types" documentation). +ARCH = AVR8 + +# Input clock frequency. +# This will define a symbol, F_USB, in all source code files equal to the +# input clock frequency (before any prescaling is performed) in Hz. This value may +# differ from F_CPU if prescaling is used on the latter, and is required as the +# raw input clock is fed directly to the PLL sections of the AVR for high speed +# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' +# at the end, this will be done automatically to create a 32-bit value in your +# source code. +# +# If no clock division is performed on the input clock inside the AVR (via the +# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. +F_USB = $(F_CPU) + + +ifdef TEENSY2 + OPT_DEFS += -DATREUS_TEENSY2 + ATREUS_UPLOAD_COMMAND = teensy_loader_cli -w -mmcu=$(MCU) $(TARGET).hex +else + OPT_DEFS += -DATREUS_ASTAR + OPT_DEFS += -DCATERINA_BOOTLOADER + ATREUS_UPLOAD_COMMAND = while [ ! -r $(USB) ]; do sleep 1; done; \ + avrdude -p $(MCU) -c avr109 -U flash:w:$(TARGET).hex -P $(USB) +endif +# Interrupt driven control endpoint task(+60) +OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT + + +# MCU name + +# Boot Section Size in *bytes* +# Teensy halfKay 512 +# Teensy++ halfKay 1024 +# Atmel DFU loader 4096 +# LUFA bootloader 4096 +# USBaspLoader 2048 +OPT_DEFS += -DBOOTLOADER_SIZE=4096 + + +# Build Options +# change yes to no to disable +# +BOOTMAGIC_ENABLE ?= no # Virtual DIP switch configuration(+1000) +MOUSEKEY_ENABLE = yes # Mouse keys(+4700) +EXTRAKEY_ENABLE = yes # Audio control and System control(+450) +CONSOLE_ENABLE ?= no # Console for debug(+400) +COMMAND_ENABLE ?= no # Commands for debug and configuration +# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE +SLEEP_LED_ENABLE ?= no # Breathing sleep LED during USB suspend +# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work +NKRO_ENABLE ?= no # USB Nkey Rollover +BACKLIGHT_ENABLE ?= no # Enable keyboard backlight functionality on B7 by default +MIDI_ENABLE ?= no # MIDI controls +UNICODE_ENABLE ?= no # Unicode +BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID +AUDIO_ENABLE ?= no # Audio output on port C6 +RGBLIGHT_ENABLE = yes + +ifndef QUANTUM_DIR + include ../../../Makefile +endif + +upload: build + $(ATREUS_UPLOAD_COMMAND) + diff --git a/keyboards/handwired/traveller/config.h b/keyboards/handwired/traveller/config.h new file mode 100644 index 0000000000..2b82da447f --- /dev/null +++ b/keyboards/handwired/traveller/config.h @@ -0,0 +1,173 @@ +/* +Copyright 2012 Jun Wako <wakojun@gmail.com> + +This program is free software: you can redistribute it and/or modify +it under the terms of the GNU General Public License as published by +the Free Software Foundation, either version 2 of the License, or +(at your option) any later version. + +This program is distributed in the hope that it will be useful, +but WITHOUT ANY WARRANTY; without even the implied warranty of +MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +GNU General Public License for more details. + +You should have received a copy of the GNU General Public License +along with this program. If not, see <http://www.gnu.org/licenses/>. +*/ + +#ifndef CONFIG_H +#define CONFIG_H + +#include "config_common.h" + +/* USB Device descriptor parameter */ +#define VENDOR_ID 0xFEED +#define PRODUCT_ID 0x6060 +#define DEVICE_VER 0x0001 +#define MANUFACTURER You +#define PRODUCT traveller +#define DESCRIPTION A custom keyboard + +/* key matrix size */ +#define MATRIX_ROWS 4 +#define MATRIX_COLS 13 + +/* + * Keyboard Matrix Assignments + * + * Change this to how you wired your keyboard + * COLS: AVR pins used for columns, left to right + * ROWS: AVR pins used for rows, top to bottom + * DIODE_DIRECTION: COL2ROW = COL = Anode (+), ROW = Cathode (-, marked on diode) + * ROW2COL = ROW = Anode (+), COL = Cathode (-, marked on diode) + * +*/ +#define MATRIX_ROW_PINS { D0, D1, D3, D2 } + // no I can't say why this order seemed like a good idea +#define MATRIX_COL_PINS { B5, D6, B7, B6, F6, B1, B3, F7, B4, E6, D7, C6, D4 } +#define UNUSED_PINS + +// LED stuff +#define RGB_DI_PIN B2 +//#define RBLIGHT_TIMER +#define RGBLED_NUM 1 // Number of LEDs +#define RGBLIGHT_HUE_STEP 10 +#define RGBLIGHT_SAT_STEP 17 +#define RGBLIGHT_VAL_STEP 17 + + +/* COL2ROW or ROW2COL */ +#define DIODE_DIRECTION COL2ROW + +// #define BACKLIGHT_PIN B7 +// #define BACKLIGHT_BREATHING +// #define BACKLIGHT_LEVELS 3 + + +/* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */ +#define DEBOUNCING_DELAY 5 + +/* define if matrix has ghost (lacks anti-ghosting diodes) */ +//#define MATRIX_HAS_GHOST + +/* number of backlight levels */ +#define BACKLIGHT_LEVELS 3 + +/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */ +//#define LOCKING_SUPPORT_ENABLE +/* Locking resynchronize hack */ +#define LOCKING_RESYNC_ENABLE + +/* + * Force NKRO + * + * Force NKRO (nKey Rollover) to be enabled by default, regardless of the saved + * state in the bootmagic EEPROM settings. (Note that NKRO must be enabled in the + * makefile for this to work.) + * + * If forced on, NKRO can be disabled via magic key (default = LShift+RShift+N) + * until the next keyboard reset. + * + * NKRO may prevent your keystrokes from being detected in the BIOS, but it is + * fully operational during normal computer usage. + * + * For a less heavy-handed approach, enable NKRO via magic key (LShift+RShift+N) + * or via bootmagic (hold SPACE+N while plugging in the keyboard). Once set by + * bootmagic, NKRO mode will always be enabled until it is toggled again during a + * power-up. + * + */ +//#define FORCE_NKRO + +/* + * Magic Key Options + * + * Magic keys are hotkey commands that allow control over firmware functions of + * the keyboard. They are best used in combination with the HID Listen program, + * found here: https://www.pjrc.com/teensy/hid_listen.html + * + * The options below allow the magic key functionality to be changed. This is + * useful if your keyboard/keypad is missing keys and you want magic key support. + * + */ + +/* key combination for magic key command */ +#define IS_COMMAND() ( \ + keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)) \ +) + +/* control how magic key switches layers */ +//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS true +//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS true +//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM false + +/* override magic key keymap */ +//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS +//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS +//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM +//#define MAGIC_KEY_HELP1 H +//#define MAGIC_KEY_HELP2 SLASH +//#define MAGIC_KEY_DEBUG D +//#define MAGIC_KEY_DEBUG_MATRIX X +//#define MAGIC_KEY_DEBUG_KBD K +//#define MAGIC_KEY_DEBUG_MOUSE M +//#define MAGIC_KEY_VERSION V +//#define MAGIC_KEY_STATUS S +//#define MAGIC_KEY_CONSOLE C +//#define MAGIC_KEY_LAYER0_ALT1 ESC +//#define MAGIC_KEY_LAYER0_ALT2 GRAVE +//#define MAGIC_KEY_LAYER0 0 +//#define MAGIC_KEY_LAYER1 1 +//#define MAGIC_KEY_LAYER2 2 +//#define MAGIC_KEY_LAYER3 3 +//#define MAGIC_KEY_LAYER4 4 +//#define MAGIC_KEY_LAYER5 5 +//#define MAGIC_KEY_LAYER6 6 +//#define MAGIC_KEY_LAYER7 7 +//#define MAGIC_KEY_LAYER8 8 +//#define MAGIC_KEY_LAYER9 9 +//#define MAGIC_KEY_BOOTLOADER PAUSE +//#define MAGIC_KEY_LOCK CAPS +//#define MAGIC_KEY_EEPROM E +//#define MAGIC_KEY_NKRO N +//#define MAGIC_KEY_SLEEP_LED Z + +/* + * Feature disable options + * These options are also useful to firmware size reduction. + */ + +/* disable debug print */ +//#define NO_DEBUG + +/* disable print */ +//#define NO_PRINT + +/* disable action features */ +//#define NO_ACTION_LAYER +//#define NO_ACTION_TAPPING +//#define NO_ACTION_ONESHOT +//#define NO_ACTION_MACRO +//#define NO_ACTION_FUNCTION + +#endif diff --git a/keyboards/handwired/traveller/keymaps/default/keymap.c b/keyboards/handwired/traveller/keymaps/default/keymap.c new file mode 100644 index 0000000000..13d889ab8b --- /dev/null +++ b/keyboards/handwired/traveller/keymaps/default/keymap.c @@ -0,0 +1,305 @@ +#include "traveller.h" +#include "mousekey.h" +#include "action_layer.h" + +// Each layer gets a name for readability, which is then used in the keymap matrix below. +// The underscores don't mean anything - you can have a layer called STUFF or any other name. +#define _QW 0 +#define _LW 1 +#define _HI 2 +#define _NAV 4 +#define _CUR 5 +#define _FKEYS 6 +#define _TRNS 8 + +// We do the same trick for functions +#define RGBLED_TOGGLE 10 +#define _HIOUT 15 +#define _LWOUT 16 +// Macros +#define MDL 4 +#define MDR 5 +#define MUR 6 +#define MUL 3 + + + +const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { +/* Qwerty + * ,-----------------------------------------. .-----------------------------------------. + * | NAV | ` ~ | W | E | R | T | | Y | U | I | O | - | = | + * |------+------+------+------+------+------| |------+------+------+------+------+------| + * | Tab | Q | S | D | F | G | | H | J | K | L | P | \ | + * |------+------+------+------+------+------|------+------+------+------+------+------+------| + *|ctrl/esc| A | X | C | V | B |Ctrl /| N | M | , | . | ; | ' | + * |------+------+------+------+------+------+ // +------+------+------+------+------+------| + * | Shift| Z | Del | GUI | Low | Bspc |/Enter| Spc | Hi | GUI | Alt | / |Shift | + * `------------------------------------------------------------------------------------------' + * + */ +[_QW] = KEYMAP( + F(_NAV), KC_GRV, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_MINS, KC_EQL, + KC_TAB, KC_Q, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, KC_P, KC_BSLS, + CTL_T(KC_ESC), KC_A, KC_X, KC_C, KC_V, KC_B, KC_RCTL, KC_N, KC_M, KC_COMM, KC_DOT, KC_SCLN, KC_QUOT, + KC_LSFT, KC_Z, KC_DEL, KC_LGUI, MO(_LW), KC_BSPC, KC_ENTER, KC_SPC, MO(_HI), KC_RGUI, KC_RALT, KC_SLSH, KC_RSFT + ), + +/* LOW - numbers, missing or awkward programming keys + Doubled 1 key allows lazy reach with ring finger. + * ,-----------------------------------------. .-----------------------------------------. + * | FKeys| 1 | 2 | 3 | 4 | 5 | | 6 | 7 | 8 | 9 | 0 |Ctrl-alt-del| + * |------+------+------+------+------+------| +------+------+------+------+------+------| + * | Tab | 1 | ] | ( | ) | | | * | ( | ) | [ | | | + * |------+------+------+------+------+------|------+------+------+------+------+------+------| + * | Caps | [ | | { | } | ` | /| # | { | } | | ] | | + * |------+------+------+------+------+------+ // +------+------+------+------+------+------| + * | Shift| | | | Low | |/ | | Hi | | | |Shift | + * `------------------------------------------------------------------------------------------' + * + */ + +[_LW] = KEYMAP( + F(_FKEYS), KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, LCTL(LALT(KC_DEL)) , + KC_TRNS, KC_1, KC_RBRC, KC_LPRN, KC_RPRN, KC_NO, KC_ASTR, KC_LPRN, KC_RPRN, KC_LBRC, KC_NO, KC_NO, + KC_CAPS, KC_LBRC, KC_NO, KC_LCBR, KC_RCBR, KC_TILD, KC_TRNS, KC_HASH, KC_LCBR, KC_RCBR, KC_NO, KC_RBRC, KC_NO, + KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS +), + +/* HI - Punctuation, shell and +url ://@.com row on bottom, && is opposite || ^$ are in regex order: ^.*$ +Right hand nav keys work pretty well chorded with the Right hand Hi Key + * ,-----------------------------------------. .-----------------------------------------. + * |FKEYS | ! | @ | # | $ | % | | ^ | & | * | ( | ) | + | + * |------+------+------+------+------+------| |------+------+------+------+------+------| + * | | ! | & | "|" | $ | % | | Vol+| Mute| | | | | + * |------+------+------+------+------+------|------+------+------+------+------+------+------| + * | CAPS | ^ | : | . | * | - | /| Vol-| Play | PgUp | Home | Up | End | + * |------+------+------+------+------+------+ // +------+------+------+------+------+------| + * | | / | | | Low | |/ | | Hi | PgDn | Left| Down | Right | + * `------------------------------------------------------------------------------------------' + * + */ + +[_HI] = KEYMAP( + F(_FKEYS), KC_EXLM, KC_AT, KC_HASH, KC_DLR, KC_PERC, KC_CIRC, KC_AMPR, KC_ASTR, KC_LPRN, KC_RPRN, KC_PLUS, + KC_TRNS, KC_EXLM, KC_AMPR, KC_PIPE, KC_DLR, KC_PERC, KC_VOLU, KC_MUTE, KC_NO, KC_NO, KC_NO, KC_NO, + KC_CAPS, KC_CIRC, KC_COLN, KC_DOT, KC_ASTR, KC_MINS, KC_TRNS, KC_VOLD, KC_PPLS, KC_PGUP, KC_HOME, KC_UP, KC_END, + KC_TRNS, KC_SLSH, KC_TRNS, KC_TRNS, F(_LW), KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_PGDN, KC_LEFT, KC_DOWN, KC_RIGHT +), + +/* NAV - mouse & navigation +//gui left and right are line home/end, or fore & back in browser +// Mouse buttons are reversed for comfort - bigger stretch is to the right button. + + * ,-----------------------------------------. .-----------------------------------------. +* | NAV | | | Up | |Gui-> | | MwU | MS_UL| MS_U |MS_UR | |Ms Norm| +* |------+------+------+------+------+------| |------+------+------+------+------+--------| +* | |Gui<- | Left | Down |Right | C^E | | BTN3 | MS_L |MS Up | MS_R | |Ms Fast | +* |------+------+------+------+------+------|------|------+------+------+------+------+--------| +* | | C^A | GUI X| GUI C| GUI_V| |Enter/| MWD | M_DL |MS Dwn|MS_DR | Up |Ms Slow | +* |------+------+------+------+------+------+ // +------+------+------+------+------+------| +* | | GuiZ | | | Low | |/ButnR|ButnL | Hi | | Left | Down | Right | +* `------------------------------------------------------------------------------------------' +*/ + +[_NAV] = KEYMAP( + F(_NAV), KC_NO, KC_NO, KC_UP, KC_NO, RGUI(KC_RIGHT), KC_WH_U, M(MUL), KC_MS_U, M(MUR), KC_NO, KC_ACL2, + KC_TRNS, RGUI(KC_LEFT), KC_LEFT, KC_DOWN, KC_RIGHT, LCTL(KC_E), KC_BTN3, KC_MS_L, KC_MS_U, KC_MS_R, KC_NO, KC_ACL1, + KC_TRNS, LCTL(KC_A), LGUI(KC_X),RGUI(KC_C), RGUI(KC_V),KC_NO, KC_ENTER, KC_WH_D, M(MDL), KC_MS_D, M(MDR), KC_UP, KC_ACL0, + KC_TRNS, RGUI(KC_Z), KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_BTN2, KC_BTN1, KC_TRNS, KC_TRNS, KC_LEFT, KC_DOWN, KC_RIGHT +), + +/* FKEYS - Funtion keys & mac stuff + * ,-----------------------------------------. .-----------------------------------------. + * | FKEYS| F1 | F2 | F3 | F4 | F5 | | F6 | F7 | F8 | F9 | F10 | Ctrl | + * |------+------+------+------+------+------| |------+------+------+------+------+------| + * | | | | | | | | F11 | F12 | F13 | F14 | F15 | Alt | + * |------+------+------+------+------+------|------+------+------+------+------+------+------| + * |Qwerty| | | | | | /| | | | | | Del | + * |------+------+------+------+------+------+ // +------+------+------+------+------+------| + * | . |RGBTog| . | | LO | Bspc |/ | | HI | | | | | + * `------------------------------------------------------------------------------------------' + * + */ + +[_FKEYS] = KEYMAP( + F(_FKEYS), KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_F7, KC_F8, KC_F9, KC_F10, KC_RCTL, |