3 files changed, 3 insertions, 67 deletions
diff --git a/keyboards/evyd13/eon65/config.h b/keyboards/evyd13/eon65/config.h
index d5bf5b47fb..844b00b5eb 100644
--- a/keyboards/evyd13/eon65/config.h
+++ b/keyboards/evyd13/eon65/config.h
@@ -16,7 +16,6 @@
 
 #pragma once
 
-#include "config_common.h"
 
 /* key matrix size */
 #define MATRIX_ROWS 5
@@ -38,23 +37,8 @@
 /* COL2ROW, ROW2COL*/
 #define DIODE_DIRECTION COL2ROW
 
-/*
- * Split Keyboard specific options, make sure you have 'SPLIT_KEYBOARD = yes' in your rules.mk, and define SOFT_SERIAL_PIN.
- */
-// #define SOFT_SERIAL_PIN D0 // or D1, D2, D3, E6
-
-// #define BACKLIGHT_PIN B7
-// #define BACKLIGHT_BREATHING
-// #define BACKLIGHT_LEVELS 3
-
  #define RGB_DI_PIN E6
- #ifdef RGB_DI_PIN
    #define RGBLED_NUM 10
-//   #define RGBLIGHT_HUE_STEP 8
-//   #define RGBLIGHT_SAT_STEP 8
-//   #define RGBLIGHT_VAL_STEP 8
-//   #define RGBLIGHT_LIMIT_VAL 255 /* The maximum brightness level */
-//   #define RGBLIGHT_SLEEP  /* If defined, the RGB lighting will be switched off when the host goes to sleep */
 #define RGBLIGHT_EFFECT_BREATHING
 #define RGBLIGHT_EFFECT_RAINBOW_MOOD
 #define RGBLIGHT_EFFECT_RAINBOW_SWIRL
@@ -65,51 +49,12 @@
 #define RGBLIGHT_EFFECT_RGB_TEST
 #define RGBLIGHT_EFFECT_ALTERNATING
 #define RGBLIGHT_EFFECT_TWINKLE
-// /*== customize breathing effect ==*/
-//   /*==== (DEFAULT) use fixed table instead of exp() and sin() ====*/
-//   #define RGBLIGHT_BREATHE_TABLE_SIZE 256      // 256(default) or 128 or 64
-//   /*==== use exp() and sin() ====*/
-//   #define RGBLIGHT_EFFECT_BREATHE_CENTER 1.85  // 1 to 2.7
-//   #define RGBLIGHT_EFFECT_BREATHE_MAX    255   // 0 to 255
- #endif
-
-/* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */
-#define DEBOUNCE 5
-
-/* define if matrix has ghost (lacks anti-ghosting diodes) */
-//#define MATRIX_HAS_GHOST
 
 /* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */
 #define LOCKING_SUPPORT_ENABLE
 /* Locking resynchronize hack */
 #define LOCKING_RESYNC_ENABLE
 
-/* If defined, GRAVE_ESC will always act as ESC when CTRL is held.
- * This is userful for the Windows task manager shortcut (ctrl+shift+esc).
- */
-// #define GRAVE_ESC_CTRL_OVERRIDE
-
-/*
- * Force NKRO
- *
- * Force NKRO (nKey Rollover) to be enabled by default, regardless of the saved
- * state in the bootmagic EEPROM settings. (Note that NKRO must be enabled in the
- * makefile for this to work.)
- *
- * If forced on, NKRO can be disabled via magic key (default = LShift+RShift+N)
- * until the next keyboard reset.
- *
- * NKRO may prevent your keystrokes from being detected in the BIOS, but it is
- * fully operational during normal computer usage.
- *
- * For a less heavy-handed approach, enable NKRO via magic key (LShift+RShift+N)
- * or via bootmagic (hold SPACE+N while plugging in the keyboard). Once set by
- * bootmagic, NKRO mode will always be enabled until it is toggled again during a
- * power-up.
- *
- */
-//#define FORCE_NKRO
-
 /*
  * Feature disable options
  *  These options are also useful to firmware size reduction.
@@ -125,7 +70,3 @@
 //#define NO_ACTION_LAYER
 //#define NO_ACTION_TAPPING
 //#define NO_ACTION_ONESHOT
-
-/* Bootmagic Lite key configuration */
-// #define BOOTMAGIC_LITE_ROW 0
-// #define BOOTMAGIC_LITE_COLUMN 0
diff --git a/keyboards/evyd13/eon65/info.json b/keyboards/evyd13/eon65/info.json
index 26f70f5a52..9f1a67689f 100644
--- a/keyboards/evyd13/eon65/info.json
+++ b/keyboards/evyd13/eon65/info.json
@@ -8,6 +8,9 @@
         "pid": "0xAEB4",
         "device_version": "0.0.1"
     },
+    "processor": "atmega32u4",
+    "bootloader": "atmel-dfu",
+    "community_layouts": ["65_ansi", "65_ansi_blocker", "65_iso", "65_iso_blocker"],
     "layouts": {
         "LAYOUT_all": {
             "layout": [
diff --git a/keyboards/evyd13/eon65/rules.mk b/keyboards/evyd13/eon65/rules.mk
index 990f7e04ca..8eee1b53bb 100644
--- a/keyboards/evyd13/eon65/rules.mk
+++ b/keyboards/evyd13/eon65/rules.mk
@@ -1,9 +1,3 @@
-# MCU name
-MCU = atmega32u4
-
-# Bootloader selection
-BOOTLOADER = atmel-dfu
-
 # Build Options
 #   change yes to no to disable
 #
@@ -16,5 +10,3 @@ NKRO_ENABLE = no            # Enable N-Key Rollover
 BACKLIGHT_ENABLE = no       # Enable keyboard backlight functionality
 RGBLIGHT_ENABLE = yes       # Enable keyboard RGB underglow
 AUDIO_ENABLE = no           # Audio output
-
-LAYOUTS = 65_ansi 65_ansi_blocker 65_iso 65_iso_blocker