2 files changed, 2 insertions, 63 deletions
diff --git a/keyboards/evyd13/atom47/rev5/config.h b/keyboards/evyd13/atom47/rev5/config.h
index 9a751580db..e965023763 100644
--- a/keyboards/evyd13/atom47/rev5/config.h
+++ b/keyboards/evyd13/atom47/rev5/config.h
@@ -17,7 +17,6 @@ along with this program.  If not, see <http://www.gnu.org/licenses/>.
 
 #pragma once
 
-#include "config_common.h"
 
 /* key matrix size */
 #define MATRIX_ROWS 4
@@ -39,69 +38,11 @@ along with this program.  If not, see <http://www.gnu.org/licenses/>.
 /* COL2ROW, ROW2COL */
 #define DIODE_DIRECTION COL2ROW
 
-//#define LED_NUM_LOCK_PIN B0
-//#define LED_CAPS_LOCK_PIN B1
-//#define LED_SCROLL_LOCK_PIN B2
-//#define LED_COMPOSE_PIN B3
-//#define LED_KANA_PIN B4
-
-//#define BACKLIGHT_PIN B7
-//#define BACKLIGHT_LEVELS 3
-//#define BACKLIGHT_BREATHING
-
-//#define RGB_DI_PIN E2
-//#ifdef RGB_DI_PIN
-//#    define RGBLED_NUM 16
-//#    define RGBLIGHT_HUE_STEP 8
-//#    define RGBLIGHT_SAT_STEP 8
-//#    define RGBLIGHT_VAL_STEP 8
-//#    define RGBLIGHT_LIMIT_VAL 255 /* The maximum brightness level */
-//#    define RGBLIGHT_SLEEP  /* If defined, the RGB lighting will be switched off when the host goes to sleep */
-/*== customize breathing effect ==*/
-/*==== (DEFAULT) use fixed table instead of exp() and sin() ====*/
-//#    define RGBLIGHT_BREATHE_TABLE_SIZE 256      // 256(default) or 128 or 64
-/*==== use exp() and sin() ====*/
-//#    define RGBLIGHT_EFFECT_BREATHE_CENTER 1.85  // 1 to 2.7
-//#    define RGBLIGHT_EFFECT_BREATHE_MAX    255   // 0 to 255
-//#endif
-
-/* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */
-#define DEBOUNCE 5
-
-/* define if matrix has ghost (lacks anti-ghosting diodes) */
-//#define MATRIX_HAS_GHOST
-
 /* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */
 #define LOCKING_SUPPORT_ENABLE
 /* Locking resynchronize hack */
 #define LOCKING_RESYNC_ENABLE
 
-/* If defined, GRAVE_ESC will always act as ESC when CTRL is held.
- * This is useful for the Windows task manager shortcut (ctrl+shift+esc).
- */
-//#define GRAVE_ESC_CTRL_OVERRIDE
-
-/*
- * Force NKRO
- *
- * Force NKRO (nKey Rollover) to be enabled by default, regardless of the saved
- * state in the bootmagic EEPROM settings. (Note that NKRO must be enabled in the
- * makefile for this to work.)
- *
- * If forced on, NKRO can be disabled via magic key (default = LShift+RShift+N)
- * until the next keyboard reset.
- *
- * NKRO may prevent your keystrokes from being detected in the BIOS, but it is
- * fully operational during normal computer usage.
- *
- * For a less heavy-handed approach, enable NKRO via magic key (LShift+RShift+N)
- * or via bootmagic (hold SPACE+N while plugging in the keyboard). Once set by
- * bootmagic, NKRO mode will always be enabled until it is toggled again during a
- * power-up.
- *
- */
-//#define FORCE_NKRO
-
 /*
  * Feature disable options
  *  These options are also useful to firmware size reduction.
@@ -118,10 +59,6 @@ along with this program.  If not, see <http://www.gnu.org/licenses/>.
 //#define NO_ACTION_TAPPING
 //#define NO_ACTION_ONESHOT
 
-/* Bootmagic Lite key configuration */
-//#define BOOTMAGIC_LITE_ROW 0
-//#define BOOTMAGIC_LITE_COLUMN 0
-
 // This is a 7-bit address, that gets left-shifted and bit 0
 // set to 0 for write, 1 for read (as per I2C protocol)
 // The address will vary depending on your wiring:
diff --git a/keyboards/evyd13/atom47/rev5/info.json b/keyboards/evyd13/atom47/rev5/info.json
index 4ecc240182..847cac0b73 100644
--- a/keyboards/evyd13/atom47/rev5/info.json
+++ b/keyboards/evyd13/atom47/rev5/info.json
@@ -8,6 +8,8 @@
         "pid": "0x92EA",
         "device_version": "0.0.1"
     },
+    "processor": "atmega32u4",
+    "bootloader": "qmk-dfu",
     "layouts": {
         "LAYOUT_split_space": {
             "layout": [