diff options
Diffstat (limited to 'keyboards/ergodox')
| -rw-r--r-- | keyboards/ergodox/Makefile | 33 | ||||
| -rw-r--r-- | keyboards/ergodox/ez/Makefile | 77 | ||||
| -rw-r--r-- | keyboards/ergodox/ez/rules.mk | 76 | ||||
| -rw-r--r-- | keyboards/ergodox/infinity/Makefile | 78 | ||||
| -rw-r--r-- | keyboards/ergodox/infinity/rules.mk | 77 | ||||
| -rw-r--r-- | keyboards/ergodox/readme.md | 12 | ||||
| -rw-r--r-- | keyboards/ergodox/rules.mk | 28 |
7 files changed, 192 insertions, 189 deletions
diff --git a/keyboards/ergodox/Makefile b/keyboards/ergodox/Makefile index 05fb588d11..7165350050 100644 --- a/keyboards/ergodox/Makefile +++ b/keyboards/ergodox/Makefile @@ -1,34 +1,5 @@ -#---------------------------------------------------------------------------- -# On command line: -# -# make = Make software. -# -# make clean = Clean out built project files. -# -# That's pretty much all you need. To compile, always go make clean, -# followed by make. -# -# For advanced users only: -# make teensy = Download the hex file to the device, using teensy_loader_cli. -# (must have teensy_loader_cli installed). -# -#---------------------------------------------------------------------------- SUBPROJECT_DEFAULT = ez -# Build Options -# comment out to disable the options. -# -BOOTMAGIC_ENABLE ?= no # Virtual DIP switch configuration(+1000) -MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700) -EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) -CONSOLE_ENABLE ?= no # Console for debug(+400) -COMMAND_ENABLE ?= yes # Commands for debug and configuration -CUSTOM_MATRIX ?= yes # Custom matrix file for the ErgoDox EZ -SLEEP_LED_ENABLE ?= yes # Breathing sleep LED during USB suspend -NKRO_ENABLE ?= yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work -MIDI_ENABLE ?= no # MIDI controls -UNICODE_ENABLE ?= yes # Unicode - -ifndef QUANTUM_DIR +ifndef MAKEFILE_INCLUDED include ../../Makefile -endif +endif
\ No newline at end of file diff --git a/keyboards/ergodox/ez/Makefile b/keyboards/ergodox/ez/Makefile index 37e554b304..191c6bb664 100644 --- a/keyboards/ergodox/ez/Makefile +++ b/keyboards/ergodox/ez/Makefile @@ -1,76 +1,3 @@ -#---------------------------------------------------------------------------- -# On command line: -# -# make = Make software. -# -# make clean = Clean out built project files. -# -# That's pretty much all you need. To compile, always go make clean, -# followed by make. -# -# For advanced users only: -# make teensy = Download the hex file to the device, using teensy_loader_cli. -# (must have teensy_loader_cli installed). -# -#---------------------------------------------------------------------------- - -# # project specific files -SRC = twimaster.c \ - matrix.c - -# MCU name -MCU = atmega32u4 - -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - -# Boot Section Size in *bytes* -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 -OPT_DEFS += -DBOOTLOADER_SIZE=512 - - -# Build Options -# comment out to disable the options. -# - -ifndef QUANTUM_DIR +ifndef MAKEFILE_INCLUDED include ../../../Makefile -endif +endif
\ No newline at end of file diff --git a/keyboards/ergodox/ez/rules.mk b/keyboards/ergodox/ez/rules.mk new file mode 100644 index 0000000000..37e554b304 --- /dev/null +++ b/keyboards/ergodox/ez/rules.mk @@ -0,0 +1,76 @@ +#---------------------------------------------------------------------------- +# On command line: +# +# make = Make software. +# +# make clean = Clean out built project files. +# +# That's pretty much all you need. To compile, always go make clean, +# followed by make. +# +# For advanced users only: +# make teensy = Download the hex file to the device, using teensy_loader_cli. +# (must have teensy_loader_cli installed). +# +#---------------------------------------------------------------------------- + +# # project specific files +SRC = twimaster.c \ + matrix.c + +# MCU name +MCU = atmega32u4 + +# Processor frequency. +# This will define a symbol, F_CPU, in all source code files equal to the +# processor frequency in Hz. You can then use this symbol in your source code to +# calculate timings. Do NOT tack on a 'UL' at the end, this will be done +# automatically to create a 32-bit value in your source code. +# +# This will be an integer division of F_USB below, as it is sourced by +# F_USB after it has run through any CPU prescalers. Note that this value +# does not *change* the processor frequency - it should merely be updated to +# reflect the processor speed set externally so that the code can use accurate +# software delays. +F_CPU = 16000000 + + +# +# LUFA specific +# +# Target architecture (see library "Board Types" documentation). +ARCH = AVR8 + +# Input clock frequency. +# This will define a symbol, F_USB, in all source code files equal to the +# input clock frequency (before any prescaling is performed) in Hz. This value may +# differ from F_CPU if prescaling is used on the latter, and is required as the +# raw input clock is fed directly to the PLL sections of the AVR for high speed +# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' +# at the end, this will be done automatically to create a 32-bit value in your +# source code. +# +# If no clock division is performed on the input clock inside the AVR (via the +# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. +F_USB = $(F_CPU) + +# Interrupt driven control endpoint task(+60) +OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT + + +# Boot Section Size in *bytes* +# Teensy halfKay 512 +# Teensy++ halfKay 1024 +# Atmel DFU loader 4096 +# LUFA bootloader 4096 +# USBaspLoader 2048 +OPT_DEFS += -DBOOTLOADER_SIZE=512 + + +# Build Options +# comment out to disable the options. +# + +ifndef QUANTUM_DIR + include ../../../Makefile +endif diff --git a/keyboards/ergodox/infinity/Makefile b/keyboards/ergodox/infinity/Makefile index ccb735a485..191c6bb664 100644 --- a/keyboards/ergodox/infinity/Makefile +++ b/keyboards/ergodox/infinity/Makefile @@ -1,77 +1,3 @@ -# project specific files -SRC = matrix.c \ - led.c - -## chip/board settings -# - the next two should match the directories in -# <chibios>/os/hal/ports/$(MCU_FAMILY)/$(MCU_SERIES) -# - For Teensies, FAMILY = KINETIS and SERIES is either -# KL2x (LC) or K20x (3.0,3.1,3.2). -# - For Infinity KB, SERIES = K20x -MCU_FAMILY = KINETIS -MCU_SERIES = K20x - -# Linker script to use -# - it should exist either in <chibios>/os/common/ports/ARMCMx/compilers/GCC/ld/ -# or <this_dir>/ld/ -# - NOTE: a custom ld script is needed for EEPROM on Teensy LC -# - LDSCRIPT = -# - MKL26Z64 for Teensy LC -# - MK20DX128 for Teensy 3.0 -# - MK20DX256 for Teensy 3.1 and 3.2 -# - MK20DX128BLDR4 for Infinity 60% with Kiibohd bootloader -# - MK20DX256BLDR8 for Infinity ErgoDox with Kiibohd bootloader -MCU_LDSCRIPT = MK20DX256BLDR8 - -# Startup code to use -# - it should exist in <chibios>/os/common/ports/ARMCMx/compilers/GCC/mk/ -# - STARTUP = -# - kl2x for Teensy LC -# - k20x5 for Teensy 3.0 and Infinity 60% -# - k20x7 for Teensy 3.1, 3.2 and Infinity ErgoDox -MCU_STARTUP = k20x7 - -# Board: it should exist either in <chibios>/os/hal/boards/ -# or <this_dir>/boards -# - BOARD = -# - PJRC_TEENSY_LC for Teensy LC -# - PJRC_TEENSY_3 for Teensy 3.0 -# - PJRC_TEENSY_3_1 for Teensy 3.1 or 3.2 -# - MCHCK_K20 for Infinity KB -#BOARD = MCHCK_K20 -BOARD = PJRC_TEENSY_3_1 - -# Cortex version -# Teensy LC is cortex-m0; Teensy 3.x are cortex-m4 -MCU = cortex-m4 - -# ARM version, CORTEX-M0/M1 are 6, CORTEX-M3/M4/M7 are 7 -# I.e. 6 for Teensy LC; 7 for Teensy 3.x -ARMV = 7 - -# Vector table for application -# 0x00000000-0x00001000 area is occupied by bootlaoder.*/ -# The CORTEX_VTOR... is needed only for MCHCK/Infinity KB -OPT_DEFS += -DCORTEX_VTOR_INIT=0x00002000 - -# Build Options -# comment out to disable the options. -# -CUSTOM_MATRIX ?= yes # Custom matrix file -SERIAL_LINK_ENABLE = yes -VISUALIZER_ENABLE ?= no #temporarily disabled to make everything compile -LCD_ENABLE ?= yes -LED_ENABLE ?= yes -LCD_BACKLIGHT_ENABLE ?= yes - -ifndef QUANTUM_DIR +ifndef MAKEFILE_INCLUDED include ../../../Makefile -endif - -ifdef LCD_ENABLE -include $(SUBPROJECT_PATH)/drivers/gdisp/st7565ergodox/driver.mk -endif - -ifdef LED_ENABLE -include $(SUBPROJECT_PATH)/drivers/gdisp/IS31FL3731C/driver.mk -endif +endif
\ No newline at end of file diff --git a/keyboards/ergodox/infinity/rules.mk b/keyboards/ergodox/infinity/rules.mk new file mode 100644 index 0000000000..ccb735a485 --- /dev/null +++ b/keyboards/ergodox/infinity/rules.mk @@ -0,0 +1,77 @@ +# project specific files +SRC = matrix.c \ + led.c + +## chip/board settings +# - the next two should match the directories in +# <chibios>/os/hal/ports/$(MCU_FAMILY)/$(MCU_SERIES) +# - For Teensies, FAMILY = KINETIS and SERIES is either +# KL2x (LC) or K20x (3.0,3.1,3.2). +# - For Infinity KB, SERIES = K20x +MCU_FAMILY = KINETIS +MCU_SERIES = K20x + +# Linker script to use +# - it should exist either in <chibios>/os/common/ports/ARMCMx/compilers/GCC/ld/ +# or <this_dir>/ld/ +# - NOTE: a custom ld script is needed for EEPROM on Teensy LC +# - LDSCRIPT = +# - MKL26Z64 for Teensy LC +# - MK20DX128 for Teensy 3.0 +# - MK20DX256 for Teensy 3.1 and 3.2 +# - MK20DX128BLDR4 for Infinity 60% with Kiibohd bootloader +# - MK20DX256BLDR8 for Infinity ErgoDox with Kiibohd bootloader +MCU_LDSCRIPT = MK20DX256BLDR8 + +# Startup code to use +# - it should exist in <chibios>/os/common/ports/ARMCMx/compilers/GCC/mk/ +# - STARTUP = +# - kl2x for Teensy LC +# - k20x5 for Teensy 3.0 and Infinity 60% +# - k20x7 for Teensy 3.1, 3.2 and Infinity ErgoDox +MCU_STARTUP = k20x7 + +# Board: it should exist either in <chibios>/os/hal/boards/ +# or <this_dir>/boards +# - BOARD = +# - PJRC_TEENSY_LC for Teensy LC +# - PJRC_TEENSY_3 for Teensy 3.0 +# - PJRC_TEENSY_3_1 for Teensy 3.1 or 3.2 +# - MCHCK_K20 for Infinity KB +#BOARD = MCHCK_K20 +BOARD = PJRC_TEENSY_3_1 + +# Cortex version +# Teensy LC is cortex-m0; Teensy 3.x are cortex-m4 +MCU = cortex-m4 + +# ARM version, CORTEX-M0/M1 are 6, CORTEX-M3/M4/M7 are 7 +# I.e. 6 for Teensy LC; 7 for Teensy 3.x +ARMV = 7 + +# Vector table for application +# 0x00000000-0x00001000 area is occupied by bootlaoder.*/ +# The CORTEX_VTOR... is needed only for MCHCK/Infinity KB +OPT_DEFS += -DCORTEX_VTOR_INIT=0x00002000 + +# Build Options +# comment out to disable the options. +# +CUSTOM_MATRIX ?= yes # Custom matrix file +SERIAL_LINK_ENABLE = yes +VISUALIZER_ENABLE ?= no #temporarily disabled to make everything compile +LCD_ENABLE ?= yes +LED_ENABLE ?= yes +LCD_BACKLIGHT_ENABLE ?= yes + +ifndef QUANTUM_DIR + include ../../../Makefile +endif + +ifdef LCD_ENABLE +include $(SUBPROJECT_PATH)/drivers/gdisp/st7565ergodox/driver.mk +endif + +ifdef LED_ENABLE +include $(SUBPROJECT_PATH)/drivers/gdisp/IS31FL3731C/driver.mk +endif diff --git a/keyboards/ergodox/readme.md b/keyboards/ergodox/readme.md index b113ca7dd2..3bbe98fd69 100644 --- a/keyboards/ergodox/readme.md +++ b/keyboards/ergodox/readme.md @@ -72,9 +72,7 @@ Some distributions provide a binary, maybe called `teensy-loader-cli`). To flash the firmware: - - Build the firmware with `make keymap=keymapname`, for example `make - keymap=default` - + - Build the firmware with `make keymapname`, for example `make default` - This will result in a hex file called `ergodox_ez_keymapname.hex`, e.g. `ergodox_ez_default.hex` @@ -92,21 +90,21 @@ To flash the firmware: The Infinity is two completely independent keyboards, and needs to be flashed for the left and right halves seperately. To flash them: - - Build the firmware with `make keymap=keymapname subproject=infinity` + - Build the firmware with `make infinity-keymapname` - Plug in the left hand keyboard only. - Press the program button (back of keyboard, above thumb pad). - - Install the firmware with `sudo make dfu-util keymap=keymapname subproject=infinity` + - Install the firmware with `sudo make infinity-keymapname-dfu-util` - - Build left hand firmware with `make keymap=keymapname subproject=infinity MASTER=right` + - Build left hand firmware with `make infinity-keymapname MASTER=right` - Plug in the right hand keyboard only. - Press the program button (back of keyboard, above thumb pad). - - Install the firmware with `sudo make dfu-util keymap=keymapname subproject=infinity MASTER=right` + - Install the firmware with `sudo make infinity-keymapname-dfu-util MASTER=right` More information on the Infinity firmware is available in the [TMK/chibios for Input Club Infinity Ergodox](https://github.com/fredizzimo/infinity_ergodox/blob/master/README.md) diff --git a/keyboards/ergodox/rules.mk b/keyboards/ergodox/rules.mk new file mode 100644 index 0000000000..ac63d4eff2 --- /dev/null +++ b/keyboards/ergodox/rules.mk @@ -0,0 +1,28 @@ +#---------------------------------------------------------------------------- +# On command line: +# +# make = Make software. +# +# make clean = Clean out built project files. +# +# That's pretty much all you need. To compile, always go make clean, +# followed by make. +# +# For advanced users only: +# make teensy = Download the hex file to the device, using teensy_loader_cli. +# (must have teensy_loader_cli installed). +# +#---------------------------------------------------------------------------- +# Build Options +# comment out to disable the options. +# +BOOTMAGIC_ENABLE ?= no # Virtual DIP switch configuration(+1000) +MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700) +EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) +CONSOLE_ENABLE ?= no # Console for debug(+400) +COMMAND_ENABLE ?= yes # Commands for debug and configuration +CUSTOM_MATRIX ?= yes # Custom matrix file for the ErgoDox EZ +SLEEP_LED_ENABLE ?= yes # Breathing sleep LED during USB suspend +NKRO_ENABLE ?= yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work +MIDI_ENABLE ?= no # MIDI controls +UNICODE_ENABLE ?= yes # Unicode |