diff options
Diffstat (limited to 'keyboards/dichotemy/rules.mk')
| -rw-r--r-- | keyboards/dichotemy/rules.mk | 75 |
1 files changed, 0 insertions, 75 deletions
diff --git a/keyboards/dichotemy/rules.mk b/keyboards/dichotemy/rules.mk deleted file mode 100644 index 4e9db86875..0000000000 --- a/keyboards/dichotemy/rules.mk +++ /dev/null @@ -1,75 +0,0 @@ - -OPT_DEFS += -DDICHOTEMY_PROMICRO -DICHOTEMY_UPLOAD_COMMAND = while [ ! -r $(USB) ]; do sleep 1; done; \ - avrdude -p $(MCU) -c avr109 -U flash:w:$(TARGET).hex -P $(USB) - -# # project specific files -SRC = matrix.c - - -# MCU name -#MCU = at90usb1287 -MCU = atmega32u4 - -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Bootloader -# This definition is optional, and if your keyboard supports multiple bootloaders of -# different sizes, comment this out, and the correct address will be loaded -# automatically (+60). See bootloader.mk for all options. -BOOTLOADER = caterina - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - -# Build Options -# comment out to disable the options. -# -#BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000) -#MOUSEKEY_ENABLE = yes # Mouse keys(+4700) -POINTING_DEVICE_ENABLE = yes # Generic Pointer, not as big as mouse keys hopefully. -EXTRAKEY_ENABLE = yes # Audio control and System control(+450) -CONSOLE_ENABLE = yes # Console for debug(+400) -COMMAND_ENABLE = yes # Commands for debug and configuration -CUSTOM_MATRIX = yes # Remote matrix from the wireless bridge -# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE -# SLEEP_LED_ENABLE = yes # Breathing sleep LED during USB suspend -NKRO_ENABLE = yes # USB Nkey Rollover - not yet supported in LUFA -# BACKLIGHT_ENABLE = yes # Enable keyboard backlight functionality -# MIDI_ENABLE = YES # MIDI controls -UNICODE_ENABLE = YES # Unicode -# BLUETOOTH_ENABLE = yes # Enable Bluetooth with the Adafruit EZ-Key HID - -USB = /dev/ttyACM0 - -#upload: build -# $(DICHOTEMY_UPLOAD_COMMAND) |