1 files changed, 0 insertions, 55 deletions
diff --git a/keyboards/converter/palm_usb/config.h b/keyboards/converter/palm_usb/config.h
index 4afc654e85..35032835cd 100644
--- a/keyboards/converter/palm_usb/config.h
+++ b/keyboards/converter/palm_usb/config.h
@@ -60,58 +60,3 @@ along with this program.  If not, see <http://www.gnu.org/licenses/>.
     get_mods() == (MOD_BIT(KC_LGUI) | MOD_BIT(KC_RGUI)) || \
     get_mods() == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)) \
 )
-
-
-/* Serial(USART) configuration
- *     asynchronous, negative logic, 9600baud, no flow control
- *     1-start bit, 8-data bit, non parity, 1-stop bit
- */
-#define SERIAL_SOFT_BAUD            9600
-#define SERIAL_SOFT_PARITY_NONE
-#define SERIAL_SOFT_BIT_ORDER_LSB
-#if (HANDSPRING == 0)
-    #define SERIAL_SOFT_LOGIC_NEGATIVE  //RS232 logic
-#endif
-/* RXD Port */
-#define SERIAL_SOFT_RXD_ENABLE
-
-// we are using Pro micro pin 3 / D0 as serial
-#define SERIAL_SOFT_RXD_DDR         DDRD
-#define SERIAL_SOFT_RXD_PORT        PORTD
-#define SERIAL_SOFT_RXD_PIN         PIND
-#define SERIAL_SOFT_RXD_BIT         0
-#define SERIAL_SOFT_RXD_VECT        INT0_vect
-
-/* RXD Interupt */
-#define SERIAL_SOFT_RXD_INIT()      do { \
-    /* pin configuration: input with pull-up */ \
-    SERIAL_SOFT_RXD_DDR &= ~(1<<SERIAL_SOFT_RXD_BIT); \
-    SERIAL_SOFT_RXD_PORT |= (1<<SERIAL_SOFT_RXD_BIT); \
-    /* enable interrupt: INT0(rising edge) */ \
-    EICRA |= ((1<<ISC01)|(1<<ISC00)); \
-    EIMSK |= (1<<INT0); \
-    sei(); \
-} while (0)
-#define SERIAL_SOFT_RXD_INT_ENTER()
-#define SERIAL_SOFT_RXD_INT_EXIT()  do { \
-    /* clear interrupt  flag */ \
-    EIFR = (1<<INTF0); \
-} while (0)
-#define SERIAL_SOFT_RXD_READ()      (SERIAL_SOFT_RXD_PIN&(1<<SERIAL_SOFT_RXD_BIT))
-
-/* TXD Port */
-#define SERIAL_SOFT_TXD_ENABLE
-#define SERIAL_SOFT_TXD_DDR         DDRD
-#define SERIAL_SOFT_TXD_PORT        PORTD
-#define SERIAL_SOFT_TXD_PIN         PIND
-#define SERIAL_SOFT_TXD_BIT         3
-#define SERIAL_SOFT_TXD_HI()        do { SERIAL_SOFT_TXD_PORT |=  (1<<SERIAL_SOFT_TXD_BIT); } while (0)
-#define SERIAL_SOFT_TXD_LO()        do { SERIAL_SOFT_TXD_PORT &= ~(1<<SERIAL_SOFT_TXD_BIT); } while (0)
-#define SERIAL_SOFT_TXD_INIT()      do { \
-    /* pin configuration: output */ \
-    SERIAL_SOFT_TXD_DDR |= (1<<SERIAL_SOFT_TXD_BIT); \
-    /* idle */ \
-    SERIAL_SOFT_TXD_ON(); \
-} while (0)
-
-