diff options
Diffstat (limited to 'keyboards/converter/m0110_usb/rules.mk')
| -rw-r--r-- | keyboards/converter/m0110_usb/rules.mk | 73 |
1 files changed, 73 insertions, 0 deletions
diff --git a/keyboards/converter/m0110_usb/rules.mk b/keyboards/converter/m0110_usb/rules.mk new file mode 100644 index 0000000000..3b4ca83b75 --- /dev/null +++ b/keyboards/converter/m0110_usb/rules.mk @@ -0,0 +1,73 @@ +# MCU name +# atmega32u4 Teensy2.0 +# atemga32u4 TMK Converter rev.1 +# atemga32u2 TMK Converter rev.2 +MCU = atmega32u4 + +# Processor frequency. +# This will define a symbol, F_CPU, in all source code files equal to the +# processor frequency in Hz. You can then use this symbol in your source code to +# calculate timings. Do NOT tack on a 'UL' at the end, this will be done +# automatically to create a 32-bit value in your source code. +# +# This will be an integer division of F_USB below, as it is sourced by +# F_USB after it has run through any CPU prescalers. Note that this value +# does not *change* the processor frequency - it should merely be updated to +# reflect the processor speed set externally so that the code can use accurate +# software delays. +# +#F_CPU = 16000000 +F_CPU = 8000000 + +# +# LUFA specific +# +# Target architecture (see library "Board Types" documentation). +ARCH = AVR8 + +# Input clock frequency. +# This will define a symbol, F_USB, in all source code files equal to the +# input clock frequency (before any prescaling is performed) in Hz. This value may +# differ from F_CPU if prescaling is used on the latter, and is required as the +# raw input clock is fed directly to the PLL sections of the AVR for high speed +# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' +# at the end, this will be done automatically to create a 32-bit value in your +# source code. +# +# If no clock division is performed on the input clock inside the AVR (via the +# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. +F_USB = $(F_CPU) + +# Interrupt driven control endpoint task(+60) +OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT + +# Bootloader +# This definition is optional, and if your keyboard supports multiple bootloaders of +# different sizes, comment this out, and the correct address will be loaded +# automatically (+60). See bootloader.mk for all options. +BOOTLOADER = caterina + +# Boot Section Size in *bytes* +# Teensy halfKay 512 +# Teensy++ halfKay 1024 +# Atmel DFU loader 4096 for TMK Converter rev.1/rev.2 +# LUFA bootloader 4096 +# USBaspLoader 2048 + +# Build Options +# comment out to disable the options. +# +BOOTMAGIC_ENABLE = no # Virtual DIP switch configuration(+1000) +MOUSEKEY_ENABLE = no # Mouse keys(+4700) +CONSOLE_ENABLE = yes # Console for debug(+400) +COMMAND_ENABLE = no # Commands for debug and configuration +SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend +NKRO_ENABLE = no # USB Nkey Rollover - not yet supported in LUFA +EXTRAKEY_ENABLE = yes +USB_HID_ENABLE = yes +BACKLIGHT_ENABLE = no +#BLUETOOTH = AdafruitBLE # For Adafruit Feather 32U4 BLE support, uncomment this line + +CUSTOM_MATRIX = yes +SRC = matrix.c \ + m0110.c |