diff options
Diffstat (limited to 'keyboards/clueboard/card/rules.mk')
| -rw-r--r-- | keyboards/clueboard/card/rules.mk | 71 |
1 files changed, 11 insertions, 60 deletions
diff --git a/keyboards/clueboard/card/rules.mk b/keyboards/clueboard/card/rules.mk index 2117c81272..37b439e75a 100644 --- a/keyboards/clueboard/card/rules.mk +++ b/keyboards/clueboard/card/rules.mk @@ -1,70 +1,21 @@ - - -# MCU name -#MCU = at90usb1287 MCU = atmega32u4 - -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. F_CPU = 16000000 - - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - -# Boot Section Size in *bytes* -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 OPT_DEFS += -DBOOTLOADER_SIZE=4096 # Build Options -# change yes to no to disable -# BOOTMAGIC_ENABLE = no # Virtual DIP switch configuration(+1000) -MOUSEKEY_ENABLE = yes # Mouse keys(+4700) -EXTRAKEY_ENABLE = yes # Audio control and System control(+450) -CONSOLE_ENABLE = yes # Console for debug(+400) -COMMAND_ENABLE = yes # Commands for debug and configuration -# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE -SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend -# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work -NKRO_ENABLE = no # USB Nkey Rollover -RGBLIGHT_ENABLE = yes # Enable keyboard underlight functionality (+4870) -BACKLIGHT_ENABLE = yes # Enable keyboard backlight functionality by default -MIDI_ENABLE = no # MIDI controls -UNICODE_ENABLE = no # Unicode -BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID -AUDIO_ENABLE = yes # Audio output on port C6 +MOUSEKEY_ENABLE = yes # Mouse keys(+4700) +EXTRAKEY_ENABLE = yes # Audio control and System control(+450) +CONSOLE_ENABLE = yes # Console for debug(+400) +COMMAND_ENABLE = yes # Commands for debug and configuration +NKRO_ENABLE = no # USB Nkey Rollover +RGBLIGHT_ENABLE = yes # Enable keyboard underlight functionality (+4870) +BACKLIGHT_ENABLE = yes # Enable keyboard backlight functionality by default +MIDI_ENABLE = no # MIDI controls +UNICODE_ENABLE = no # Unicode +BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID +AUDIO_ENABLE = yes # Audio output on port C6 |