diff options
Diffstat (limited to 'keyboards/clueboard/2x1800/rules.mk')
| -rw-r--r-- | keyboards/clueboard/2x1800/rules.mk | 60 |
1 files changed, 8 insertions, 52 deletions
diff --git a/keyboards/clueboard/2x1800/rules.mk b/keyboards/clueboard/2x1800/rules.mk index 516a536f6b..eb679b9fb7 100644 --- a/keyboards/clueboard/2x1800/rules.mk +++ b/keyboards/clueboard/2x1800/rules.mk @@ -1,64 +1,20 @@ -# MCU name +# MCU details MCU = at90usb1286 - -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. F_CPU = 16000000 - - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - -# Boot Section Size in *bytes* -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 OPT_DEFS += -DBOOTLOADER_SIZE=1024 # Build Options -# change yes to no to disable -# -BOOTMAGIC_ENABLE = no # Virtual DIP switch configuration(+1000) -MOUSEKEY_ENABLE = no # Mouse keys(+4700) -EXTRAKEY_ENABLE = no # Audio control and System control(+450) +BOOTMAGIC_ENABLE = no # Virtual DIP switch configuration(+1000) +MOUSEKEY_ENABLE = yes # Mouse keys(+4700) +EXTRAKEY_ENABLE = yes # Audio control and System control(+450) CONSOLE_ENABLE = yes # Console for debug(+400) -COMMAND_ENABLE = yes # Commands for debug and configuration -# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work -NKRO_ENABLE = yes # USB Nkey Rollover +COMMAND_ENABLE = no # Commands for debug and configuration +NKRO_ENABLE = yes # USB Nkey Rollover MIDI_ENABLE = no # MIDI support (+2400 to 4200, depending on config) UNICODE_ENABLE = no # Unicode -RGBLIGHT_ENABLE = no # RGB on port C6 -AUDIO_ENABLE = no # Audio output on port C4 and B7 -FAUXCLICKY_ENABLE = no # Use buzzer to emulate clicky switches +RGBLIGHT_ENABLE = yes # RGB on port C6 +AUDIO_ENABLE = yes # Audio output on port C4 and B7 |