summaryrefslogtreecommitdiffstats
path: root/keyboards/amj60
diff options
context:
space:
mode:
Diffstat (limited to 'keyboards/amj60')
-rw-r--r--keyboards/amj60/Makefile71
-rw-r--r--keyboards/amj60/rules.mk66
2 files changed, 68 insertions, 69 deletions
diff --git a/keyboards/amj60/Makefile b/keyboards/amj60/Makefile
index 1f695aa4d8..4e2a6f00fd 100644
--- a/keyboards/amj60/Makefile
+++ b/keyboards/amj60/Makefile
@@ -1,70 +1,3 @@
-
-# MCU name
-#MCU = at90usb1287
-MCU = atmega32u4
-
-# Processor frequency.
-# This will define a symbol, F_CPU, in all source code files equal to the
-# processor frequency in Hz. You can then use this symbol in your source code to
-# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-# automatically to create a 32-bit value in your source code.
-#
-# This will be an integer division of F_USB below, as it is sourced by
-# F_USB after it has run through any CPU prescalers. Note that this value
-# does not *change* the processor frequency - it should merely be updated to
-# reflect the processor speed set externally so that the code can use accurate
-# software delays.
-F_CPU = 16000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-# This will define a symbol, F_USB, in all source code files equal to the
-# input clock frequency (before any prescaling is performed) in Hz. This value may
-# differ from F_CPU if prescaling is used on the latter, and is required as the
-# raw input clock is fed directly to the PLL sections of the AVR for high speed
-# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-# at the end, this will be done automatically to create a 32-bit value in your
-# source code.
-#
-# If no clock division is performed on the input clock inside the AVR (via the
-# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
-# Boot Section Size in *bytes*
-# Teensy halfKay 512
-# Teensy++ halfKay 1024
-# Atmel DFU loader 4096
-# LUFA bootloader 4096
-# USBaspLoader 2048
-OPT_DEFS += -DBOOTLOADER_SIZE=4096
-
-
-# Build Options
-# comment out to disable the options.
-#
-BOOTMAGIC_ENABLE ?= no # Virtual DIP switch configuration(+1000)
-MOUSEKEY_ENABLE ?= no # Mouse keys(+4700)
-EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450)
-CONSOLE_ENABLE ?= yes # Console for debug(+400)
-COMMAND_ENABLE ?= yes # Commands for debug and configuration
-NKRO_ENABLE ?= yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
-RGBLIGHT_ENABLE ?= yes # Enable keyboard underlight functionality (+4870)
-BACKLIGHT_ENABLE ?= yes # Enable keyboard backlight functionality (+1150)
-MIDI_ENABLE ?= no # MIDI controls
-AUDIO_ENABLE ?= no
-UNICODE_ENABLE ?= no # Unicode
-BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID
-
-ifndef QUANTUM_DIR
+ifndef MAKEFILE_INCLUDED
include ../../Makefile
-endif
+endif \ No newline at end of file
diff --git a/keyboards/amj60/rules.mk b/keyboards/amj60/rules.mk
new file mode 100644
index 0000000000..18403ac328
--- /dev/null
+++ b/keyboards/amj60/rules.mk
@@ -0,0 +1,66 @@
+
+# MCU name
+#MCU = at90usb1287
+MCU = atmega32u4
+
+# Processor frequency.
+# This will define a symbol, F_CPU, in all source code files equal to the
+# processor frequency in Hz. You can then use this symbol in your source code to
+# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
+# automatically to create a 32-bit value in your source code.
+#
+# This will be an integer division of F_USB below, as it is sourced by
+# F_USB after it has run through any CPU prescalers. Note that this value
+# does not *change* the processor frequency - it should merely be updated to
+# reflect the processor speed set externally so that the code can use accurate
+# software delays.
+F_CPU = 16000000
+
+
+#
+# LUFA specific
+#
+# Target architecture (see library "Board Types" documentation).
+ARCH = AVR8
+
+# Input clock frequency.
+# This will define a symbol, F_USB, in all source code files equal to the
+# input clock frequency (before any prescaling is performed) in Hz. This value may
+# differ from F_CPU if prescaling is used on the latter, and is required as the
+# raw input clock is fed directly to the PLL sections of the AVR for high speed
+# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
+# at the end, this will be done automatically to create a 32-bit value in your
+# source code.
+#
+# If no clock division is performed on the input clock inside the AVR (via the
+# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
+F_USB = $(F_CPU)
+
+# Interrupt driven control endpoint task(+60)
+OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
+
+
+# Boot Section Size in *bytes*
+# Teensy halfKay 512
+# Teensy++ halfKay 1024
+# Atmel DFU loader 4096
+# LUFA bootloader 4096
+# USBaspLoader 2048
+OPT_DEFS += -DBOOTLOADER_SIZE=4096
+
+
+# Build Options
+# comment out to disable the options.
+#
+BOOTMAGIC_ENABLE ?= no # Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE ?= no # Mouse keys(+4700)
+EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450)
+CONSOLE_ENABLE ?= yes # Console for debug(+400)
+COMMAND_ENABLE ?= yes # Commands for debug and configuration
+NKRO_ENABLE ?= yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
+RGBLIGHT_ENABLE ?= yes # Enable keyboard underlight functionality (+4870)
+BACKLIGHT_ENABLE ?= yes # Enable keyboard backlight functionality (+1150)
+MIDI_ENABLE ?= no # MIDI controls
+AUDIO_ENABLE ?= no
+UNICODE_ENABLE ?= no # Unicode
+BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID