diff options
Diffstat (limited to 'keyboards/40percentclub/4pack/config.h')
| -rw-r--r-- | keyboards/40percentclub/4pack/config.h | 87 |
1 files changed, 0 insertions, 87 deletions
diff --git a/keyboards/40percentclub/4pack/config.h b/keyboards/40percentclub/4pack/config.h index 2f89089428..2fc00cdc89 100644 --- a/keyboards/40percentclub/4pack/config.h +++ b/keyboards/40percentclub/4pack/config.h @@ -17,98 +17,15 @@ along with this program. If not, see <http://www.gnu.org/licenses/>. #pragma once -#include "config_common.h" - -/* key matrix size */ -#define MATRIX_ROWS 1 -#define MATRIX_COLS 4 - -/* - * Keyboard Matrix Assignments - * - * Change this to how you wired your keyboard - * COLS: AVR pins used for columns, left to right - * ROWS: AVR pins used for rows, top to bottom - * DIODE_DIRECTION: COL2ROW = COL = Anode (+), ROW = Cathode (-, marked on diode) - * ROW2COL = ROW = Anode (+), COL = Cathode (-, marked on diode) - * - */ -// #define MATRIX_ROW_PINS { B0 } // B0 equivalents the ground pin -// #define MATRIX_COL_PINS { E6, D7, C6, D4 } -#define DIRECT_PINS { \ - { E6, D7, C6, D4 } \ -} - -/* COL2ROW, ROW2COL*/ -#define DIODE_DIRECTION COL2ROW - - -/* - * Split Keyboard specific options, make sure you have 'SPLIT_KEYBOARD = yes' in your rules.mk, and define SOFT_SERIAL_PIN. - */ -// #define SOFT_SERIAL_PIN D0 // or D1, D2, D3, E6 - -// #define BACKLIGHT_PIN B7 -// #define BACKLIGHT_BREATHING -// #define BACKLIGHT_LEVELS 3 #define BACKLIGHT_LED_COUNT 2 #undef BACKLIGHT_PIN #define BACKLIGHT_PINS { F6, F7 } - -// #define RGB_DI_PIN E2 -// #ifdef RGB_DI_PIN -// #define RGBLED_NUM 16 -// #define RGBLIGHT_HUE_STEP 8 -// #define RGBLIGHT_SAT_STEP 8 -// #define RGBLIGHT_VAL_STEP 8 -// #define RGBLIGHT_LIMIT_VAL 255 /* The maximum brightness level */ -// #define RGBLIGHT_SLEEP /* If defined, the RGB lighting will be switched off when the host goes to sleep */ -// /*== customize breathing effect ==*/ -// /*==== (DEFAULT) use fixed table instead of exp() and sin() ====*/ -// #define RGBLIGHT_BREATHE_TABLE_SIZE 256 // 256(default) or 128 or 64 -// /*==== use exp() and sin() ====*/ -// #define RGBLIGHT_EFFECT_BREATHE_CENTER 1.85 // 1 to 2.7 -// #define RGBLIGHT_EFFECT_BREATHE_MAX 255 // 0 to 255 -// #endif - -/* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */ -#define DEBOUNCE 5 - -/* define if matrix has ghost (lacks anti-ghosting diodes) */ -//#define MATRIX_HAS_GHOST - /* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */ #define LOCKING_SUPPORT_ENABLE /* Locking resynchronize hack */ #define LOCKING_RESYNC_ENABLE -/* If defined, GRAVE_ESC will always act as ESC when CTRL is held. - * This is userful for the Windows task manager shortcut (ctrl+shift+esc). - */ -// #define GRAVE_ESC_CTRL_OVERRIDE - -/* - * Force NKRO - * - * Force NKRO (nKey Rollover) to be enabled by default, regardless of the saved - * state in the bootmagic EEPROM settings. (Note that NKRO must be enabled in the - * makefile for this to work.) - * - * If forced on, NKRO can be disabled via magic key (default = LShift+RShift+N) - * until the next keyboard reset. - * - * NKRO may prevent your keystrokes from being detected in the BIOS, but it is - * fully operational during normal computer usage. - * - * For a less heavy-handed approach, enable NKRO via magic key (LShift+RShift+N) - * or via bootmagic (hold SPACE+N while plugging in the keyboard). Once set by - * bootmagic, NKRO mode will always be enabled until it is toggled again during a - * power-up. - * - */ -//#define FORCE_NKRO - /* * Feature disable options * These options are also useful to firmware size reduction. @@ -124,7 +41,3 @@ along with this program. If not, see <http://www.gnu.org/licenses/>. //#define NO_ACTION_LAYER //#define NO_ACTION_TAPPING //#define NO_ACTION_ONESHOT - -/* Bootmagic Lite key configuration */ -// #define BOOTMAGIC_LITE_ROW 0 -// #define BOOTMAGIC_LITE_COLUMN 0 |