diff options
Diffstat (limited to 'keyboard')
103 files changed, 6908 insertions, 1774 deletions
diff --git a/keyboard/hhkb/Makefile.nodebug b/keyboard/atomic/Makefile index 578ba70c45..c4e0cb45d7 100644 --- a/keyboard/hhkb/Makefile.nodebug +++ b/keyboard/atomic/Makefile @@ -39,7 +39,7 @@ #---------------------------------------------------------------------------- # Target file name (without extension). -TARGET = hhkb_lufa +TARGET = atomic_lufa # Directory common source filess exist TOP_DIR = ../.. @@ -47,25 +47,22 @@ TOP_DIR = ../.. # Directory keyboard dependent files exist TARGET_DIR = . - -# List C source files here. (C dependencies are automatically generated.) -SRC += keymap_common.c \ +# project specific files +SRC = keymap_common.c \ matrix.c \ led.c ifdef KEYMAP SRC := keymap_$(KEYMAP).c $(SRC) else - SRC := keymap_hasu.c $(SRC) + SRC := keymap_vlad.c $(SRC) endif CONFIG_H = config.h # MCU name -# PJRC Teensy++ 2.0 -#MCU = at90usb1286 -# TMK Alt Controller or PJRC Teensy 2.0 +#MCU = at90usb1287 MCU = atmega32u4 # Processor frequency. @@ -101,14 +98,14 @@ ARCH = AVR8 # CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. F_USB = $(F_CPU) -# Interrupt driven control endpoint task -#OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT +# Interrupt driven control endpoint task(+60) +OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT # Boot Section Size in *bytes* # Teensy halfKay 512 # Teensy++ halfKay 1024 -# Atmel DFU loader 4096 (TMK Alt Controller) +# Atmel DFU loader 4096 # LUFA bootloader 4096 # USBaspLoader 2048 OPT_DEFS += -DBOOTLOADER_SIZE=4096 @@ -117,14 +114,17 @@ OPT_DEFS += -DBOOTLOADER_SIZE=4096 # Build Options # comment out to disable the options. # -BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration -MOUSEKEY_ENABLE = yes # Mouse keys -EXTRAKEY_ENABLE = yes # Audio control and System control -#CONSOLE_ENABLE = yes # Console for debug -COMMAND_ENABLE = yes # Commands for debug and configuration -NKRO_ENABLE = yes # USB Nkey Rollover -KEYMAP_SECTION_ENABLE = yes # fixed address keymap for keymap editor +BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000) +MOUSEKEY_ENABLE = yes # Mouse keys(+4700) +EXTRAKEY_ENABLE = yes # Audio control and System control(+450) +CONSOLE_ENABLE = yes # Console for debug(+400) +COMMAND_ENABLE = yes # Commands for debug and configuration +#SLEEP_LED_ENABLE = yes # Breathing sleep LED during USB suspend +NKRO_ENABLE = yes # USB Nkey Rollover - not yet supported in LUFA + +# Optimize size but this may cause error "relocation truncated to fit" +#EXTRALDFLAGS = -Wl,--relax # Search Path VPATH += $(TARGET_DIR) @@ -133,9 +133,3 @@ VPATH += $(TOP_DIR) include $(TOP_DIR)/protocol/lufa.mk include $(TOP_DIR)/common.mk include $(TOP_DIR)/rules.mk - -debug-on: EXTRAFLAGS += -DDEBUG -DDEBUG_ACTION -debug-on: all - -debug-off: EXTRAFLAGS += -DNO_DEBUG -DNO_PRINT -debug-off: all diff --git a/keyboard/atomic/Makefile.pjrc b/keyboard/atomic/Makefile.pjrc new file mode 100644 index 0000000000..9655ff65a9 --- /dev/null +++ b/keyboard/atomic/Makefile.pjrc @@ -0,0 +1,116 @@ +#---------------------------------------------------------------------------- +# On command line: +# +# make all = Make software. +# +# make clean = Clean out built project files. +# +# make coff = Convert ELF to AVR COFF. +# +# make extcoff = Convert ELF to AVR Extended COFF. +# +# make program = Download the hex file to the device. +# Please customize your programmer settings(PROGRAM_CMD) +# +# make teensy = Download the hex file to the device, using teensy_loader_cli. +# (must have teensy_loader_cli installed). +# +# make dfu = Download the hex file to the device, using dfu-programmer (must +# have dfu-programmer installed). +# +# make flip = Download the hex file to the device, using Atmel FLIP (must +# have Atmel FLIP installed). +# +# make dfu-ee = Download the eeprom file to the device, using dfu-programmer +# (must have dfu-programmer installed). +# +# make flip-ee = Download the eeprom file to the device, using Atmel FLIP +# (must have Atmel FLIP installed). +# +# make debug = Start either simulavr or avarice as specified for debugging, +# with avr-gdb or avr-insight as the front end for debugging. +# +# make filename.s = Just compile filename.c into the assembler code only. +# +# make filename.i = Create a preprocessed source file for use in submitting +# bug reports to the GCC project. +# +# To rebuild project do "make clean" then "make all". +#---------------------------------------------------------------------------- + +# Target file name (without extension). +TARGET = gh60_pjrc + +# Directory common source filess exist +TOP_DIR = ../.. + +# Directory keyboard dependent files exist +TARGET_DIR = . + +# project specific files +SRC = keymap_common.c \ + matrix.c \ + led.c + +ifdef KEYMAP + SRC := keymap_$(KEYMAP).c $(SRC) +else + SRC := keymap_poker.c $(SRC) +endif + +CONFIG_H = config.h + + +# MCU name, you MUST set this to match the board you are using +# type "make clean" after changing this, so all files will be rebuilt +MCU = atmega32u4 +#MCU = at90usb1286 + + +# Processor frequency. +# Normally the first thing your program should do is set the clock prescaler, +# so your program will run at the correct speed. You should also set this +# variable to same clock speed. The _delay_ms() macro uses this, and many +# examples use this variable to calculate timings. Do not add a "UL" here. +F_CPU = 16000000 + + +# Boot Section Size in *bytes* +# Teensy halfKay 512 +# Atmel DFU loader 4096 +# LUFA bootloader 4096 +OPT_DEFS += -DBOOTLOADER_SIZE=4096 + + +# Build Options +# comment out to disable the options. +# +BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000) +MOUSEKEY_ENABLE = yes # Mouse keys(+5000) +EXTRAKEY_ENABLE = yes # Audio control and System control(+600) +CONSOLE_ENABLE = yes # Console for debug +COMMAND_ENABLE = yes # Commands for debug and configuration +SLEEP_LED_ENABLE = yes # Breathing sleep LED during USB suspend +NKRO_ENABLE = yes # USB Nkey Rollover(+500) +#PS2_MOUSE_ENABLE = yes # PS/2 mouse(TrackPoint) support + + +# Search Path +VPATH += $(TARGET_DIR) +VPATH += $(TOP_DIR) + |