diff options
Diffstat (limited to 'keyboard')
33 files changed, 10562 insertions, 1654 deletions
diff --git a/keyboard/arrow_pad/Makefile b/keyboard/arrow_pad/Makefile new file mode 100644 index 0000000000..2c4ee0cae5 --- /dev/null +++ b/keyboard/arrow_pad/Makefile @@ -0,0 +1,158 @@ +#---------------------------------------------------------------------------- +# On command line: +# +# make all = Make software. +# +# make clean = Clean out built project files. +# +# make coff = Convert ELF to AVR COFF. +# +# make extcoff = Convert ELF to AVR Extended COFF. +# +# make program = Download the hex file to the device. +# Please customize your programmer settings(PROGRAM_CMD) +# +# make teensy = Download the hex file to the device, using teensy_loader_cli. +# (must have teensy_loader_cli installed). +# +# make dfu = Download the hex file to the device, using dfu-programmer (must +# have dfu-programmer installed). +# +# make flip = Download the hex file to the device, using Atmel FLIP (must +# have Atmel FLIP installed). +# +# make dfu-ee = Download the eeprom file to the device, using dfu-programmer +# (must have dfu-programmer installed). +# +# make flip-ee = Download the eeprom file to the device, using Atmel FLIP +# (must have Atmel FLIP installed). +# +# make debug = Start either simulavr or avarice as specified for debugging, +# with avr-gdb or avr-insight as the front end for debugging. +# +# make filename.s = Just compile filename.c into the assembler code only. +# +# make filename.i = Create a preprocessed source file for use in submitting +# bug reports to the GCC project. +# +# To rebuild project do "make clean" then "make all". +#---------------------------------------------------------------------------- + +# Target file name (without extension). +TARGET = arrow_pad + + +# Directory common source filess exist +TOP_DIR = ../.. +TMK_DIR = ../../tmk_core + +# Directory keyboard dependent files exist +TARGET_DIR = . + +# # project specific files +SRC = arrow_pad.c + +ifdef KEYMAP + SRC := keymaps/$(KEYMAP).c $(SRC) +else + SRC := keymaps/default.c $(SRC) +endif + +CONFIG_H = config.h + +# MCU name +#MCU = at90usb1287 +MCU = atmega32u4 + +# Processor frequency. +# This will define a symbol, F_CPU, in all source code files equal to the +# processor frequency in Hz. You can then use this symbol in your source code to +# calculate timings. Do NOT tack on a 'UL' at the end, this will be done +# automatically to create a 32-bit value in your source code. +# +# This will be an integer division of F_USB below, as it is sourced by +# F_USB after it has run through any CPU prescalers. Note that this value +# does not *change* the processor frequency - it should merely be updated to +# reflect the processor speed set externally so that the code can use accurate +# software delays. +F_CPU = 16000000 + + +# +# LUFA specific +# +# Target architecture (see library "Board Types" documentation). +ARCH = AVR8 + +# Input clock frequency. +# This will define a symbol, F_USB, in all source code files equal to the +# input clock frequency (before any prescaling is performed) in Hz. This value may +# differ from F_CPU if prescaling is used on the latter, and is required as the +# raw input clock is fed directly to the PLL sections of the AVR for high speed +# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' +# at the end, this will be done automatically to create a 32-bit value in your +# source code. +# +# If no clock division is performed on the input clock inside the AVR (via the +# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. +F_USB = $(F_CPU) + +# Interrupt driven control endpoint task(+60) +OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT + + +# Boot Section Size in *bytes* +# Teensy halfKay 512 +# Teensy++ halfKay 1024 +# Atmel DFU loader 4096 +# LUFA bootloader 4096 +# USBaspLoader 2048 +OPT_DEFS += -DBOOTLOADER_SIZE=512 + + +# Build Options +# change yes to no to disable +# +BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000) +MOUSEKEY_ENABLE = yes # Mouse keys(+4700) +EXTRAKEY_ENABLE = yes # Audio control and System control(+450) +CONSOLE_ENABLE = yes # Console for debug(+400) +COMMAND_ENABLE = yes # Commands for debug and configuration +KEYBOARD_LOCK_ENABLE = yes # Allow locking of keyboard via magic key +# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE +SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend +# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work +NKRO_ENABLE = yes # USB Nkey Rollover +BACKLIGHT_ENABLE = yes # Enable keyboard backlight functionality +MIDI_ENABLE = no # MIDI controls +UNICODE_ENABLE = no # Unicode +BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID +AUDIO_ENABLE = no # Audio output on port C6 + + +ifdef KEYMAP + +ifeq ("$(wildcard keymaps/$(KEYMAP).c)","") +ifneq ("$(wildcard keymaps/$(KEYMAP)/makefile.mk)","") + include keymaps/$(KEYMAP)/makefile.mk +endif +endif + +else + +ifneq ("$(wildcard keymaps/default/makefile.mk)","") + include keymaps/default/makefile.mk +endif + +endif + +# Optimize size but this may cause error "relocation truncated to fit" +#EXTRALDFLAGS = -Wl,--relax + +# Search Path +VPATH += $(TARGET_DIR) +VPATH += $(TOP_DIR) +VPATH += $(TMK_DIR) + +include $(TOP_DIR)/quantum/quantum.mk + diff --git a/keyboard/arrow_pad/README.md b/keyboard/arrow_pad/README.md new file mode 100644 index 0000000000..f669ad6a12 --- /dev/null +++ b/keyboard/arrow_pad/README.md @@ -0,0 +1,24 @@ +arrow_pad keyboard firmware +====================== + +## Quantum MK Firmware + +For the full Quantum feature list, see [the parent README.md](/README.md). + +## Building + +Download or clone the whole firmware and navigate to the keyboard/arrow_pad folder. Once your dev env is setup, you'll be able to type `make` to generate your .hex - you can then use the Teensy Loader to program your .hex file. + +Depending on which keymap you would like to use, you will have to compile slightly differently. + +### Default +To build with the default keymap, simply run `make`. + +### Other Keymaps +Several version of keymap are available in advance but you are recommended to define your favorite layout yourself. To define your own keymap create file named `<name>.c` in the keymaps folder, and see keymap document (you can find in top README.md) and existent keymap files. + +To build the firmware binary hex file with a keymap just do `make` with `KEYMAP` option like: +``` +$ make KEYMAP=[default|jack|<name>] +``` +Keymaps follow the format **__\<name\>.c__** and are stored in the `keymaps` folder.
\ No newline at end of file diff --git a/keyboard/arrow_pad/arrow_pad.c b/keyboard/arrow_pad/arrow_pad.c new file mode 100644 index 0000000000..f29c2c53fe --- /dev/null +++ b/keyboard/arrow_pad/arrow_pad.c @@ -0,0 +1,114 @@ +#include "arrow_pad.h" + +__attribute__ ((weak)) +void matrix_init_user(void) { + // leave this function blank - it can be defined in a keymap file +}; + +__attribute__ ((weak)) +void matrix_scan_user(void) { + // leave this function blank - it can be defined in a keymap file +} + +__attribute__ ((weak)) +bool process_action_user(keyrecord_t *record) { + // leave this function blank - it can be defined in a keymap file + return true; +} + +__attribute__ ((weak)) +void led_set_user(uint8_t usb_led) { + // leave this function blank - it can be defined in a keymap file +} + +void matrix_init_kb(void) { + // put your keyboard start-up code here + // runs once when the firmware starts up + +#ifdef BACKLIGHT_ENABLE + backlight_init_ports(); +#endif + + matrix_init_user(); +} + +void matrix_scan_kb(void) { + // put your looping keyboard code here + // runs every cycle (a lot) + + matrix_scan_user(); +} + +bool process_action_kb(keyrecord_t *record) { + // put your per-action keyboard code here + // runs for every action, just before processing by the firmware + + return process_action_user(record); +} + +void led_set_kb(uint8_t usb_led) { + // put your keyboard LED indicator (ex: Caps Lock LED) toggling code here + + led_set_user(usb_led); +} + +#ifdef BACKLIGHT_ENABLE +#define CHANNEL OCR1C + +void backlight_init_ports() +{ + + // Setup PB7 as output and output low. + DDRB |= (1<<7); + PORTB &= ~(1<<7); + + // Use full 16-bit resolution. + ICR1 = 0xFFFF; + + // I could write a wall of text here to explain... but TL;DW + // Go read the ATmega32u4 datasheet. + // And this: http://blog.saikoled.com/post/43165849837/secret-konami-cheat-code-to-high-resolution-pwm-on + + // Pin PB7 = OCR1C (Timer 1, Channel C) + // Compare Output Mode = Clear on compare match, Channel C = COM1C1=1 COM1C0=0 + // (i.e. start high, go low when counter matches.) + // WGM Mode 14 (Fast PWM) = WGM13=1 WGM12=1 WGM11=1 WGM10=0 + // Clock Select = clk/1 (no prescaling) = CS12=0 CS11=0 CS10=1 + + TCCR1A = _BV(COM1C1) | _BV(WGM11); // = 0b00001010; + TCCR1B = _BV(WGM13) | _BV(WGM12) | _BV(CS10); // = 0b00011001; + + backlight_init(); +} + +void backlight_set(uint8_t level) +{ + if ( level == 0 ) + { + // Turn off PWM control on PB7, revert to output low. + TCCR1A &= ~(_BV(COM1C1)); + CHANNEL = 0x0; + // Prevent backlight blink on lowest level + PORTB &= ~(_BV(PORTB7)); + } + else if ( level == BACKLIGHT_LEVELS ) + { + // Prevent backlight blink on lowest level + PORTB &= ~(_BV(PORTB7)); + // Turn on PWM control of PB7 + TCCR1A |= _BV(COM1C1); + // Set the brightness + CHANNEL = 0xFFFF; + } + else + { + // Prevent backlight blink on lowest level + PORTB &= ~(_BV(PORTB7)); + // Turn on PWM control of PB7 + TCCR1A |= _BV(COM1C1); + // Set the brightness + CHANNEL = 0xFFFF >> ((BACKLIGHT_LEVELS - level) * ((BACKLIGHT_LEVELS + 1) / 2)); + } +} + +#endif
\ No newline at end of file diff --git a/keyboard/arrow_pad/arrow_pad.h b/keyboard/arrow_pad/arrow_pad.h new file mode 100644 index 0000000000..2026b52d1d --- /dev/null +++ b/keyboard/arrow_pad/arrow_pad.h @@ -0,0 +1,18 @@ +#ifndef ARROW_PAD_H +#define ARROW_PAD_H + +#include "matrix.h" +#include "keymap_common.h" +#ifdef BACKLIGHT_ENABLE + #include "backlight.h" +#endif +#include <avr/io.h> +#include <stddef.h> + +void matrix_init_user(void); +void matrix_scan_user(void); +bool process_action_user(keyrecord_t *record); +void led_set_user(uint8_t usb_led); +void backlight_init_ports(void); + +#endif diff --git a/keyboard/arrow_pad/config.h b/keyboard/arrow_pad/config.h new file mode 100644 index 0000000000..9e85f3ccf6 --- /dev/null +++ b/keyboard/arrow_pad/config.h @@ -0,0 +1,158 @@ +/* +Copyright 2012 Jun Wako <wakojun@gmail.com> + +This program is free software: you can redistribute it and/or modify +it under the terms of the GNU General Public License as published by +the Free Software Foundation, either version 2 of the License, or +(at your option) any later version. + +This program is distributed in the hope that it will be useful, +but WITHOUT ANY WARRANTY; without even the implied warranty of +MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +GNU General Public License for more details. + +You should have received a copy of the GNU General Public License +along with this program. If not, see <http://www.gnu.org/licenses/>. +*/ + +#ifndef CONFIG_H +#define CONFIG_H + +#include "config_common.h" + +/* USB Device descriptor parameter */ +#define VENDOR_ID 0xFEED +#define PRODUCT_ID 0x4096 +#define DEVICE_VER 0x0001 +#define MANUFACTURER Nobody +#define PRODUCT GoldPad +#define DESCRIPTION A custom keyboard + +/* key matrix size */ +#define MATRIX_ROWS 6 +#define MATRIX_COLS 4 + +/* + * Keyboard Matrix Assignments + * + * Change this to how you wired your keyboard + * COLS: AVR pins used for columns, left to right + * ROWS: AVR pins used for rows, top to bottom + * DIODE_DIRECTION: COL2ROW = COL = Anode (+), ROW = Cathode (-, marked on diode) + * ROW2COL = ROW = Anode (+), COL = Cathode (-, marked on diode) + * +*/ +#define MATRIX_ROW_PINS { F0, F1, F4, F5, F6, F7 } +#define MATRIX_COL_PINS { B0, B1, B2, B3 } +#define UNUSED_PINS + +/* COL2ROW or ROW2COL */ +#define DIODE_DIRECTION ROW2COL + +/* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */ +#define DEBOUNCING_DELAY 5 + +/* define if matrix has ghost (lacks anti-ghosting diodes) */ +//#define MATRIX_HAS_GHOST + +/* number of backlight levels */ +#define BACKLIGHT_LEVELS 3 + +/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */ +//#define LOCKING_SUPPORT_ENABLE +/* Locking resynchronize hack */ +//#define LOCKING_RESYNC_ENABLE + +/* + * Force NKRO + * + * Force NKRO (nKey Rollover) to be enabled by default, regardless of the saved + * state in the bootmagic EEPROM settings. (Note that NKRO must be enabled in the + * makefile for this to work.) + * + * If forced on, NKRO can be disabled via magic key (default = LShift+RShift+N) + * until the next keyboard reset. + * + * NKRO may prevent your keystrokes from being detected in the BIOS, but it is + * fully operational during normal computer usage. + * + * For a less heavy-handed approach, enable NKRO via magic key (LShift+RShift+N) + * or via bootmagic (hold SPACE+N while plugging in the keyboard). Once set by + * bootmagic, NKRO mode will always be enabled until it is toggled again during a + * power-up. + * + */ +#define FORCE_NKRO + +/* + * Magic Key Options + * + * Magic keys are hotkey commands that allow control over firmware functions of + * the keyboard. They are best used in combination with the HID Listen program, + * found here: https://www.pjrc.com/teensy/hid_listen.html + * + * The options below allow the magic key functionality to be changed. This is + * useful if your keyboard/keypad is missing keys and you want magic key support. + * + */ + +/* key combination for magic key command */ +#define IS_COMMAND() ( \ + keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)) \ +) + +/* control how magic key switches layers */ +//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS true +//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS true +//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM false + +/* override magic key keymap */ +//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS +//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS +//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM +//#define MAGIC_KEY_HELP1 H +//#define MAGIC_KEY_HELP2 SLASH +//#define MAGIC_KEY_DEBUG D +//#define MAGIC_KEY_DEBUG_MATRIX X +//#define MAGIC_KEY_DEBUG_KBD K +//#define MAGIC_KEY_DEBUG_MOUSE M +//#define MAGIC_KEY_VERSION V +//#define MAGIC_KEY_STATUS S +//#define MAGIC_KEY_CONSOLE C +//#define MAGIC_KEY_LAYER0_ALT1 ESC +//#define MAGIC_KEY_LAYER0_ALT2 GRAVE +//#define MAGIC_KEY_LAYER0 0 +//#define MAGIC_KEY_LAYER1 1 +//#define MAGIC_KEY_LAYER2 2 +//#define MAGIC_KEY_LAYER3 3 +//#define MAGIC_KEY_LAYER4 4 +//#define MAGIC_KEY_LAYER5 5 +//#define MAGIC_KEY_LAYER6 6 +//#define MAGIC_KEY_LAYER7 7 +//#define MAGIC_KEY_LAYER8 8 +//#define MAGIC_KEY_LAYER9 9 +//#define MAGIC_KEY_BOOTLOADER PAUSE +//#define MAGIC_KEY_LOCK CAPS +//#define MAGIC_KEY_EEPROM E +//#define MAGIC_KEY_NKRO N +//#define MAGIC_KEY_SLEEP_LED Z + +/* + * Feature disable options + * These options are also useful to firmware size reduction. + */ + +/* disable debug print */ +//#define NO_DEBUG + +/* disable print */ +//#define NO_PRINT + +/* disable action features */ +//#define NO_ACTION_LAYER +//#define NO_ACTION_TAPPING +//#define NO_ACTION_ONESHOT +//#define NO_ACTION_MACRO +//#define NO_ACTION_FUNCTION + +#endif diff --git a/keyboard/arrow_pad/keymaps/default.c b/keyboard/arrow_pad/keymaps/default.c new file mode 100644 index 0000000000..5647f75afe --- /dev/null +++ b/keyboard/arrow_pad/keymaps/default.c @@ -0,0 +1,163 @@ +// This is the canonical layout file for the Quantum project. If you want to add another keyboard, +// this is the style you want to emulate. + +#include "arrow_pad.h" +#include "led.h" + +// This is the 21-key keypad to 2x11 element matrix mapping +#define KEYMAP( \ + KM_ESC, KM_TAB, KM_BSL, KM_ARR, \ + KM_NUM, KM_FSL, KM_AST, KM_MIN, \ + KM___7, KM___8, KM___9, KM_EQU, \ + KM___4, KM___5, KM___6, KM_PLS, \ + KM___1, KM___2, KM___3, ___ENT, \ + KM___0, _____0, KM_DOT, KM_ENT \ +) { \ + { KM_ESC, KM_TAB, KM_BSL, KM_ARR }, \ + { KM_NUM, KM_FSL, KM_AST, KM_MIN }, \ + { KM___7, KM___8, KM___9, KM_EQU }, \ + { KM___4, KM___5, KM___6, KM_PLS }, \ + { KM___1, KM___2, KM___3, KC_NO }, \ + { KM___0, KC_NO, KM_DOT, KM_ENT } \ +} + +#define LAYER_BASE 0 +#define LAYER_EDIT 1 +#define LAYER_FUNCTION 2 + +#define MACRO_COPY_CUT 0 +#define MACRO_SHIFT_CONTROL 1 +#define MACRO_CONTROL_ALT 2 + +#define M_COPY KC_FN5 +#define M_SHFCT KC_FN6 +#define M_CTALT KC_FN7 + +#define SC_UNDO LCTL(KC_Z) +#define SC_REDO LCTL(KC_Y) +#define SC_CUT LCTL(KC_X) +#define SC_COPY LCTL(KC_C) +#define SC_PSTE LCTL(KC_V) +#define SC_SELA LCTL(KC_A) +#define SC_SAVE LCTL(KC_S) +#define SC_OPEN LCTL(KC_O) +#define SC_ACLS LALT(KC_F4) +#define SC_CCLS LCTL(KC_F4) + +#define _______ KC_TRNS +#define XXXXXXX KC_NO + +const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { + +[LAYER_BASE] = KEYMAP( \ + KC_ESC, KC_TAB, KC_BSLS, KC_FN0, \ + KC_NLCK, KC_PSLS, KC_PAST, KC_PMNS, \ + KC_P7, KC_P8, KC_P9, KC_PEQL, \ + KC_P4, KC_P5, KC_P6, KC_PPLS, \ + KC_P1, KC_P2, KC_P3, XXXXXXX, \ + KC_P0, KC_PCMM, KC_PDOT, KC_PENT ), + +[LAYER_EDIT] = KEYMAP( \ + KC_ESC, KC_TAB, KC_SPC, _______, \ + KC_FN1, SC_PSTE, SC_REDO, SC_UNDO, \ + KC_HOME, KC_UP, KC_PGUP, KC_LALT, \ + KC_LEFT, M_COPY, KC_RGHT, KC_LCTL, \ + KC_END, KC_DOWN, KC_PGDN, XXXXXXX, \ + KC_BSPC, KC_PENT, KC_DEL, M_SHFCT), + +[LAYER_FUNCTION] = KEYMAP( \ + KC_FN2, KC_FN3, KC_FN4, _______, \ + KC_FN1, _______, _______, _______, \ + _______, _______, _______, _______, \ + _______, _______, _______, _______, \ + _______, _______, _______, XXXXXXX, \ + RESET, _______, _______, _______ ), + +}; + + +const uint16_t PROGMEM fn_actions[] = { + [0] = ACTION_LAYER_MOMENTARY(LAYER_FUNCTION), + [1] = ACTION_LAYER_TOGGLE(LAYER_EDIT), + [2] = ACTION_BACKLIGHT_TOGGLE(), + [3] = ACTION_BACKLIGHT_INCREASE(), + [4] = ACTION_BACKLIGHT_DECREASE(), + [5] = ACTION_MACRO_TAP(MACRO_COPY_CUT), + [6] = ACTION_MACRO_TAP(MACRO_SHIFT_CONTROL), + [7] = ACTION_MACRO_TAP(MACRO_CONTROL_ALT), + +}; + + +void action_function(keyrecord_t *record, uint8_t id, uint8_t opt) +{ +} + + +const macro_t *action_get_macro(keyrecord_t *record, uint8_t id, uint8_t opt) +{ + // MACRODOWN only works in this function + switch (id) { + + case MACRO_COPY_CUT: + if (record->event.pressed) { + register_code(KC_LCTL); + if (record->tap.count == 1) { + register_code(KC_C); + unregister_code(KC_C); + } + else if (record->tap.count == 2) { + register_code(KC_X); + unregister_code(KC_X); + } + unregister_code(KC_LCTL); + } + break; + + case MACRO_SHIFT_CONTROL: + if (record->event.pressed) { + if (record->tap.count <= 2) register_mods(MOD_BIT(KC_LSFT)); + if (record->tap.count == 2) register_mods(MOD_BIT(KC_LCTL)); + if (record->tap.count == 3) register_code(KC_PENT);; + } + else { + unregister_mods(MOD_BIT(KC_LSFT) | MOD_BIT(KC_LCTL)); + unregister_code(KC_PENT); + } + break; + + case MACRO_CONTROL_ALT: + if (record->event.pressed) { + if (record->tap.count < 2) register_mods(MOD_BIT(KC_LCTL)); + if (record->tap.count >= 2) register_mods(MOD_BIT(KC_LALT)); + } + else { + unregister_mods(MOD_BIT(KC_LCTL) | MOD_BIT(KC_LALT)); + } + break; + } + + return MACRO_NONE; +} + +void led_set_user(uint8_t usb_led) +{ + if (usb_led & (1<<USB_LED_CAPS_LOCK)) { + // output high + DDRD |= (1<<6); + PORTD |= (1<<6); + } else { + // Hi-Z + DDRD &= ~(1<<6); + PORTD &= ~(1<<6); + } + if (usb_led & (1<<USB_LED_NUM_LOCK)) { + // output low + DDRC |= (1<<7); + PORTC |= ~(1<<7); + } else { + // Hi-Z + DDRC &= ~(1<<7); + PORTC &= ~(1<<7); + } +}
\ No newline at end of file diff --git a/keyboard/arrow_pad/keymaps/pad_21/config.h b/keyboard/arrow_pad/keymaps/pad_21/config.h new file mode 100644 index 0000000000..a095e87374 --- /dev/null +++ b/keyboard/arrow_pad/keymaps/pad_21/config.h @@ -0,0 +1,158 @@ +/* +Copyright 2012 Jun Wako <wakojun@gmail.com> + +This program is free software: you can redistribute it and/or modify +it under the terms of the GNU General Public License as published by +the Free Software Foundation, either version 2 of the License, or +(at your option) any later version. + +This program is distributed in the hope that it will be useful, +but WITHOUT ANY WARRANTY; without even the implied warranty of +MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +GNU General Public License for more details. + +You should have received a copy of the GNU General Public License +along with this program. If not, see <http://www.gnu.org/licenses/>. +*/ + +#ifndef CONFIG_H +#define CONFIG_H + +#include "config_common.h" + +/* USB Device descriptor parameter */ +#define VENDOR_ID 0xFEED +#define PRODUCT_ID 0x4097 +#define DEVICE_VER 0x0001 +#define MANUFACTURER Nobody +#define PRODUCT Arrow Pad 21 +#define DESCRIPTION 21-Key QMK Assistant + +/* key matrix size */ +#define MATRIX_ROWS 2 +#define MATRIX_COLS 11 + +/* + * Keyboard Matrix Assignments + * + * Change this to how you wired your keyboard + * COLS: AVR pins used for columns, left to right + * ROWS: AVR pins used for rows, top to bottom + * DIODE_DIRECTION: COL2ROW = COL = Anode (+), ROW = Cathode (-, marked on diode) + * ROW2COL = ROW = Anode (+), COL = Cathode (-, marked on diode) + * +*/ +#define MATRIX_ROW_PINS { D3, D5 } +#define MATRIX_COL_PINS { F0, F1, F4, F5, F6, F7, B6, B5, B4, D7, D4 } +#define UNUSED_PINS + +/* COL2ROW or ROW2COL */ +#define DIODE_DIRECTION ROW2COL + +/* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */ +#define DEBOUNCING_DELAY 5 + +/* define if matrix has ghost (lacks anti-ghosting diodes) */ +//#define MATRIX_HAS_GHOST + +/* number of backlight levels */ +#define BACKLIGHT_LEVELS 3 + +/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */ +//#define LOCKING_SUPPORT_ENABLE +/* Locking resynchronize hack */ +//#define LOCKING_RESYNC_ENABLE + +/* + * Force NKRO + * + * Force NKRO (nKey Rollover) to be enabled by default, regardless of the saved + * state in the bootmagic EEPROM settings. (Note that NKRO must be enabled in the + * makefile for this to work.) + * + * If forced on, NKRO can be disabled via magic key (default = LShift+RShift+N) + * until the next keyboard reset. + * + * NKRO may prevent your keystrokes from being detected in the BIOS, but it is + * fully operational during normal computer usage. + * + * For a less heavy-handed approach, enable NKRO via magic key (LShift+RShift+N) + * or via bootmagic (hold SPACE+N while plugging in the keyboard). Once set by + * bootmagic, NKRO mode will always be enabled until it is toggled again during a + * power-up. + * + */ +#define FORCE_NKRO + +/* + * Magic Key Options + * + * Magic keys are hotkey commands that allow control over firmware functions of + * the keyboard. They are best used in combination with the HID Listen program, + * found here: https://www.pjrc.com/teensy/hid_listen.html + * + * The options below allow the magic key functionality to be changed. This is + * useful if your keyboard/keypad is missing keys and you want magic key support. + * + */ + +/* key combination for magic key command */ +#define IS_COMMAND() ( \ + keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)) \ +) + +/* control how magic key switches layers */ +//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS true +//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS true +//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM false + +/* override magic key keymap */ +//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS +//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS +//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM +//#define MAGIC_KEY_HELP1 H +//#define MAGIC_KEY_HELP2 SLASH +//#define MAGIC_KEY_DEBUG D +//#define MAGIC_KEY_DEBUG_MATRIX X +//#define MAGIC_KEY_DEBUG_KBD K +//#define MAGIC_KEY_DEBUG_MOUSE M +//#define MAGIC_KEY_VERSION V +//#define MAGIC_KEY_STATUS S +//#define MAGIC_KEY_CONSOLE C +//#define MAGIC_KEY_LAYER0_ALT1 ESC +//#define MAGIC_KEY_LAYER0_ALT2 GRAVE +//#define MAGIC_KEY_LAYER0 0 +//#define MAGIC_KEY_LAYER1 1 +//#define MAGIC_KEY_LAYER2 2 +//#define MAGIC_KEY_LAYER3 3 +//#define MAGIC_KEY_LAYER4 |