diff options
Diffstat (limited to 'drivers/sensors')
| -rw-r--r-- | drivers/sensors/adns9800.c | 10 | ||||
| -rw-r--r-- | drivers/sensors/pimoroni_trackball.c | 22 | ||||
| -rw-r--r-- | drivers/sensors/pimoroni_trackball.h | 9 | ||||
| -rw-r--r-- | drivers/sensors/pmw3360.c | 279 | ||||
| -rw-r--r-- | drivers/sensors/pmw3360.h | 35 | ||||
| -rw-r--r-- | drivers/sensors/pmw3389.c | 296 | ||||
| -rw-r--r-- | drivers/sensors/pmw3389.h | 76 | ||||
| -rw-r--r-- | drivers/sensors/pmw3389_firmware.h | 558 |
8 files changed, 830 insertions, 455 deletions
diff --git a/drivers/sensors/adns9800.c b/drivers/sensors/adns9800.c index c52f991804..425cf9912f 100644 --- a/drivers/sensors/adns9800.c +++ b/drivers/sensors/adns9800.c @@ -154,8 +154,8 @@ void adns9800_init() { } config_adns9800_t adns9800_get_config(void) { - uint8_t config_1 = adns9800_read(REG_Configuration_I); - return (config_adns9800_t){(config_1 & 0xFF) * CPI_STEP}; + uint8_t cpival = adns9800_read(REG_Configuration_I); + return (config_adns9800_t){(cpival & 0xFF) * CPI_STEP}; } void adns9800_set_config(config_adns9800_t config) { @@ -164,8 +164,8 @@ void adns9800_set_config(config_adns9800_t config) { } uint16_t adns9800_get_cpi(void) { - uint8_t config_1 = adns9800_read(REG_Configuration_I); - return (uint16_t){(config_1 & 0xFF) * CPI_STEP}; + uint8_t cpival = adns9800_read(REG_Configuration_I); + return (uint16_t)(cpival & 0xFF) * CPI_STEP; } void adns9800_set_cpi(uint16_t cpi) { @@ -184,7 +184,7 @@ static int16_t convertDeltaToInt(uint8_t high, uint8_t low) { } report_adns9800_t adns9800_get_report(void) { - report_adns9800_t report = {0, 0}; + report_adns9800_t report = {0}; adns9800_spi_start(); diff --git a/drivers/sensors/pimoroni_trackball.c b/drivers/sensors/pimoroni_trackball.c index 7d390056ea..2867e763bc 100644 --- a/drivers/sensors/pimoroni_trackball.c +++ b/drivers/sensors/pimoroni_trackball.c @@ -33,8 +33,24 @@ static uint16_t precision = 128; -float pimoroni_trackball_get_precision(void) { return ((float)precision / 128); } -void pimoroni_trackball_set_precision(float floatprecision) { precision = (floatprecision * 128); } +uint16_t pimoroni_trackball_get_cpi(void) { return (precision * 125); } +/** + * @brief Sets the scaling value for pimoroni trackball + * + * Sets a scaling value for pimoroni trackball to allow runtime adjustment. This isn't used by the sensor and is an + * approximation so the functions are consistent across drivers. + * + * NOTE: This rounds down to the nearest number divisable by 125 that's a positive integer, values below 125 are clamped to 125. + * + * @param cpi uint16_t + */ +void pimoroni_trackball_set_cpi(uint16_t cpi) { + if (cpi < 249) { + precision = 1; + } else { + precision = (cpi - (cpi % 125)) / 125; + } +} void pimoroni_trackball_set_rgbw(uint8_t r, uint8_t g, uint8_t b, uint8_t w) { uint8_t data[4] = {r, g, b, w}; @@ -60,7 +76,7 @@ i2c_status_t read_pimoroni_trackball(pimoroni_data_t* data) { return status; } -__attribute__((weak)) void pimironi_trackball_device_init(void) { +__attribute__((weak)) void pimoroni_trackball_device_init(void) { i2c_init(); pimoroni_trackball_set_rgbw(0x00, 0x00, 0x00, 0x00); } diff --git a/drivers/sensors/pimoroni_trackball.h b/drivers/sensors/pimoroni_trackball.h index 59ee8724ba..e20ee748a7 100644 --- a/drivers/sensors/pimoroni_trackball.h +++ b/drivers/sensors/pimoroni_trackball.h @@ -23,9 +23,6 @@ #ifndef PIMORONI_TRACKBALL_ADDRESS # define PIMORONI_TRACKBALL_ADDRESS 0x0A #endif -#ifndef PIMORONI_TRACKBALL_INTERVAL_MS -# define PIMORONI_TRACKBALL_INTERVAL_MS 8 -#endif #ifndef PIMORONI_TRACKBALL_SCALE # define PIMORONI_TRACKBALL_SCALE 5 #endif @@ -52,10 +49,10 @@ typedef struct { uint8_t click; } pimoroni_data_t; -void pimironi_trackball_device_init(void); +void pimoroni_trackball_device_init(void); void pimoroni_trackball_set_rgbw(uint8_t red, uint8_t green, uint8_t blue, uint8_t white); int16_t pimoroni_trackball_get_offsets(uint8_t negative_dir, uint8_t positive_dir, uint8_t scale); void pimoroni_trackball_adapt_values(int8_t* mouse, int16_t* offset); -float pimoroni_trackball_get_precision(void); -void pimoroni_trackball_set_precision(float precision); +uint16_t pimoroni_trackball_get_cpi(void); +void pimoroni_trackball_set_cpi(uint16_t cpi); i2c_status_t read_pimoroni_trackball(pimoroni_data_t* data); diff --git a/drivers/sensors/pmw3360.c b/drivers/sensors/pmw3360.c index 50d1c35801..0dac600cc2 100644 --- a/drivers/sensors/pmw3360.c +++ b/drivers/sensors/pmw3360.c @@ -16,67 +16,71 @@ * along with this program. If not, see <http://www.gnu.org/licenses/>. */ +#include "spi_master.h" #include "pmw3360.h" #include "wait.h" #include "debug.h" #include "print.h" -#include PMW3360_FIRMWARE_H +#include "pmw3360_firmware.h" // Registers // clang-format off -#define REG_Product_ID 0x00 -#define REG_Revision_ID 0x01 -#define REG_Motion 0x02 -#define REG_Delta_X_L 0x03 -#define REG_Delta_X_H 0x04 -#define REG_Delta_Y_L 0x05 -#define REG_Delta_Y_H 0x06 -#define REG_SQUAL 0x07 -#define REG_Raw_Data_Sum 0x08 -#define REG_Maximum_Raw_data 0x09 -#define REG_Minimum_Raw_data 0x0A -#define REG_Shutter_Lower 0x0B -#define REG_Shutter_Upper 0x0C -#define REG_Control 0x0D -#define REG_Config1 0x0F -#define REG_Config2 0x10 -#define REG_Angle_Tune 0x11 -#define REG_Frame_Capture 0x12 -#define REG_SROM_Enable 0x13 -#define REG_Run_Downshift 0x14 -#define REG_Rest1_Rate_Lower 0x15 -#define REG_Rest1_Rate_Upper 0x16 -#define REG_Rest1_Downshift 0x17 -#define REG_Rest2_Rate_Lower 0x18 -#define REG_Rest2_Rate_Upper 0x19 -#define REG_Rest2_Downshift 0x1A -#define REG_Rest3_Rate_Lower 0x1B -#define REG_Rest3_Rate_Upper 0x1C -#define REG_Observation 0x24 -#define REG_Data_Out_Lower 0x25 -#define REG_Data_Out_Upper 0x26 -#define REG_Raw_Data_Dump 0x29 -#define REG_SROM_ID 0x2A -#define REG_Min_SQ_Run 0x2B -#define REG_Raw_Data_Threshold 0x2C -#define REG_Config5 0x2F -#define REG_Power_Up_Reset 0x3A -#define REG_Shutdown 0x3B -#define REG_Inverse_Product_ID 0x3F -#define REG_LiftCutoff_Tune3 0x41 -#define REG_Angle_Snap 0x42 -#define REG_LiftCutoff_Tune1 0x4A -#define REG_Motion_Burst 0x50 -#define REG_LiftCutoff_Tune_Timeout 0x58 -#define REG_LiftCutoff_Tune_Min_Length 0x5A -#define REG_SROM_Load_Burst 0x62 -#define REG_Lift_Config 0x63 -#define REG_Raw_Data_Burst 0x64 -#define REG_LiftCutoff_Tune2 0x65 +#define REG_Product_ID 0x00 +#define REG_Revision_ID 0x01 +#define REG_Motion 0x02 +#define REG_Delta_X_L 0x03 +#define REG_Delta_X_H 0x04 +#define REG_Delta_Y_L 0x05 +#define REG_Delta_Y_H 0x06 +#define REG_SQUAL 0x07 +#define REG_Raw_Data_Sum 0x08 +#define REG_Maximum_Raw_data 0x09 +#define REG_Minimum_Raw_data 0x0a +#define REG_Shutter_Lower 0x0b +#define REG_Shutter_Upper 0x0c +#define REG_Control 0x0d +#define REG_Config1 0x0f +#define REG_Config2 0x10 +#define REG_Angle_Tune 0x11 +#define REG_Frame_Capture 0x12 +#define REG_SROM_Enable 0x13 +#define REG_Run_Downshift 0x14 +#define REG_Rest1_Rate_Lower 0x15 +#define REG_Rest1_Rate_Upper 0x16 +#define REG_Rest1_Downshift 0x17 +#define REG_Rest2_Rate_Lower 0x18 +#define REG_Rest2_Rate_Upper 0x19 +#define REG_Rest2_Downshift 0x1a +#define REG_Rest3_Rate_Lower 0x1b +#define REG_Rest3_Rate_Upper 0x1c +#define REG_Observation 0x24 +#define REG_Data_Out_Lower 0x25 +#define REG_Data_Out_Upper 0x26 +#define REG_Raw_Data_Dump 0x29 +#define REG_SROM_ID 0x2a +#define REG_Min_SQ_Run 0x2b +#define REG_Raw_Data_Threshold 0x2c +#define REG_Config5 0x2f +#define REG_Power_Up_Reset 0x3a +#define REG_Shutdown 0x3b +#define REG_Inverse_Product_ID 0x3f +#define REG_LiftCutoff_Tune3 0x41 +#define REG_Angle_Snap 0x42 +#define REG_LiftCutoff_Tune1 0x4a +#define REG_Motion_Burst 0x50 +#define REG_LiftCutoff_Tune_Timeout 0x58 +#define REG_LiftCutoff_Tune_Min_Length 0x5a +#define REG_SROM_Load_Burst 0x62 +#define REG_Lift_Config 0x63 +#define REG_Raw_Data_Burst 0x64 +#define REG_LiftCutoff_Tune2 0x65 + +#define CPI_STEP 100 // clang-format on +// limits to 0--119, resulting in a CPI range of 100 -- 12000 (as only steps of 100 are possible). #ifndef MAX_CPI -# define MAX_CPI 0x77 // limits to 0--119, should be max cpi/100 +# define MAX_CPI 0x77 #endif bool _inBurst = false; @@ -86,66 +90,50 @@ void print_byte(uint8_t byte) { dprintf("%c%c%c%c%c%c%c%c|", (byte & 0x80 ? '1' #endif #define constrain(amt, low, high) ((amt) < (low) ? (low) : ((amt) > (high) ? (high) : (amt))) -bool spi_start_adv(void) { +bool pmw3360_spi_start(void) { bool status = spi_start(PMW3360_CS_PIN, PMW3360_SPI_LSBFIRST, PMW3360_SPI_MODE, PMW3360_SPI_DIVISOR); + // tNCS-SCLK, 120ns wait_us(1); return status; } -void spi_stop_adv(void) { - wait_us(1); - spi_stop(); -} +spi_status_t pmw3360_write(uint8_t reg_addr, uint8_t data) { + pmw3360_spi_start(); -spi_status_t spi_write_adv(uint8_t reg_addr, uint8_t data) { if (reg_addr != REG_Motion_Burst) { _inBurst = false; } - spi_start_adv(); // send address of the register, with MSBit = 1 to indicate it's a write spi_status_t status = spi_write(reg_addr | 0x80); status = spi_write(data); - // tSCLK-NCS for write operation - wait_us(20); - - // tSWW/tSWR (=120us) minus tSCLK-NCS. Could be shortened, but is looks like a safe lower bound - wait_us(100); + // tSCLK-NCS for write operation is 35us + wait_us(35); spi_stop(); + + // tSWW/tSWR (=180us) minus tSCLK-NCS. Could be shortened, but is looks like a safe lower bound + wait_us(145); return status; } -uint8_t spi_read_adv(uint8_t reg_addr) { - spi_start_adv(); +uint8_t pmw3360_read(uint8_t reg_addr) { + pmw3360_spi_start(); // send adress of the register, with MSBit = 0 to indicate it's a read spi_write(reg_addr & 0x7f); - + // tSRAD (=160us) + wait_us(160); uint8_t data = spi_read(); // tSCLK-NCS for read operation is 120ns wait_us(1); + spi_stop(); // tSRW/tSRR (=20us) minus tSCLK-NCS wait_us(19); - - spi_stop(); return data; } -void pmw3360_set_cpi(uint16_t cpi) { - uint8_t cpival = constrain((cpi / 100) - 1, 0, MAX_CPI); - - spi_start_adv(); - spi_write_adv(REG_Config1, cpival); - spi_stop(); -} - -uint16_t pmw3360_get_cpi(void) { - uint8_t cpival = spi_read_adv(REG_Config1); - return (uint16_t)((cpival + 1) & 0xFF) * 100; -} - bool pmw3360_init(void) { setPinOutput(PMW3360_CS_PIN); @@ -153,42 +141,51 @@ bool pmw3360_init(void) { _inBurst = false; spi_stop(); - spi_start_adv(); + pmw3360_spi_start(); spi_stop(); - spi_write_adv(REG_Shutdown, 0xb6); // Shutdown first + pmw3360_write(REG_Shutdown, 0xb6); // Shutdown first wait_ms(300); - spi_start_adv(); + pmw3360_spi_start(); wait_us(40); - spi_stop_adv(); + spi_stop(); wait_us(40); - spi_write_adv(REG_Power_Up_Reset, 0x5a); + // power up, need to first drive NCS high then low, see above. + pmw3360_write(REG_Power_Up_Reset, 0x5a); wait_ms(50); - spi_read_adv(REG_Motion); - spi_read_adv(REG_Delta_X_L); - spi_read_adv(REG_Delta_X_H); - spi_read_adv(REG_Delta_Y_L); - spi_read_adv(REG_Delta_Y_H); + // read registers and discard + pmw3360_read(REG_Motion); + pmw3360_read(REG_Delta_X_L); + pmw3360_read(REG_Delta_X_H); + pmw3360_read(REG_Delta_Y_L); + pmw3360_read(REG_Delta_Y_H); pmw3360_upload_firmware(); - spi_stop_adv(); + spi_stop(); wait_ms(10); pmw3360_set_cpi(PMW3360_CPI); wait_ms(1); - spi_write_adv(REG_Config2, 0x00); + pmw3360_write(REG_Config2, 0x00); - spi_write_adv(REG_Angle_Tune, constrain(ROTATIONAL_TRANSFORM_ANGLE, -30, 30)); + pmw3360_write(REG_Angle_Tune, constrain(ROTATIONAL_TRANSFORM_ANGLE, -127, 127)); - spi_write_adv(REG_Lift_Config, PMW3360_LIFTOFF_DISTANCE); + pmw3360_write(REG_Lift_Config, PMW3360_LIFTOFF_DISTANCE); bool init_success = pmw3360_check_signature(); +#ifdef CONSOLE_ENABLE + if (init_success) { + dprintf("pmw3360 signature verified"); + } else { + dprintf("pmw3360 signature verification failed!"); + } +#endif writePinLow(PMW3360_CS_PIN); @@ -196,86 +193,98 @@ bool pmw3360_init(void) { } void pmw3360_upload_firmware(void) { - spi_write_adv(REG_SROM_Enable, 0x1d); + // Datasheet claims we need to disable REST mode first, but during startup + // it's already disabled and we're not turning it on ... + // pmw3360_write(REG_Config2, 0x00); // disable REST mode + pmw3360_write(REG_SROM_Enable, 0x1d); wait_ms(10); - spi_write_adv(REG_SROM_Enable, 0x18); + pmw3360_write(REG_SROM_Enable, 0x18); - spi_start_adv(); + pmw3360_spi_start(); spi_write(REG_SROM_Load_Burst | 0x80); wait_us(15); +#ifdef PMW3360_LEGACY_FIRMWARE_UPLOAD unsigned char c; for (int i = 0; i < FIRMWARE_LENGTH; i++) { c = (unsigned char)pgm_read_byte(firmware_data + i); spi_write(c); wait_us(15); } +#else + spi_transmit(firmware_data, sizeof(firmware_data)); +#endif wait_us(200); - spi_read_adv(REG_SROM_ID); - - spi_write_adv(REG_Config2, 0x00); - - spi_stop(); - wait_ms(10); + pmw3360_read(REG_SROM_ID); + pmw3360_write(REG_Config2, 0x00); } bool pmw3360_check_signature(void) { - uint8_t pid = spi_read_adv(REG_Product_ID); - uint8_t iv_pid = spi_read_adv(REG_Inverse_Product_ID); - uint8_t SROM_ver = spi_read_adv(REG_SROM_ID); + uint8_t pid = pmw3360_read(REG_Product_ID); + uint8_t iv_pid = pmw3360_read(REG_Inverse_Product_ID); + uint8_t SROM_ver = pmw3360_read(REG_SROM_ID); return (pid == firmware_signature[0] && iv_pid == firmware_signature[1] && SROM_ver == firmware_signature[2]); // signature for SROM 0x04 } +uint16_t pmw3360_get_cpi(void) { + uint8_t cpival = pmw3360_read(REG_Config1); + return (uint16_t)((cpival + 1) & 0xFF) * CPI_STEP; +} + +void pmw3360_set_cpi(uint16_t cpi) { + uint8_t cpival = constrain((cpi / CPI_STEP) - 1, 0, MAX_CPI); + pmw3360_write(REG_Config1, cpival); +} + report_pmw3360_t pmw3360_read_burst(void) { + report_pmw3360_t report = {0}; + if (!_inBurst) { #ifdef CONSOLE_ENABLE dprintf("burst on"); #endif - spi_write_adv(REG_Motion_Burst, 0x00); + pmw3360_write(REG_Motion_Burst, 0x00); _inBurst = true; } - spi_start_adv(); + pmw3360_spi_start(); spi_write(REG_Motion_Burst); - wait_us(35); // waits for tSRAD + wait_us(35); // waits for tSRAD_MOTBR - report_pmw3360_t data = {0}; + report.motion = spi_read(); + spi_read(); // skip Observation + // delta registers + report.dx = spi_read(); + report.mdx = spi_read(); + report.dy = spi_read(); + report.mdy = spi_read(); - data.motion = spi_read(); - spi_write(0x00); // skip Observation - data.dx = spi_read(); - data.mdx = spi_read(); - data.dy = spi_read(); - data.mdy = spi_read(); + if (report.motion & 0b111) { // panic recovery, sometimes burst mode works weird. + _inBurst = false; + } spi_stop(); #ifdef CONSOLE_ENABLE if (debug_mouse) { - print_byte(data.motion); - print_byte(data.dx); - print_byte(data.mdx); - print_byte(data.dy); - print_byte(data.mdy); + print_byte(report.motion); + print_byte(report.dx); + print_byte(report.mdx); + print_byte(report.dy); + print_byte(report.mdy); dprintf("\n"); } #endif - data.isMotion = (data.motion & 0x80) != 0; - data.isOnSurface = (data.motion & 0x08) == 0; - data.dx |= (data.mdx << 8); - data.dx = data.dx * -1; - data.dy |= (data.mdy << 8); - data.dy = data.dy * -1; - - spi_stop(); + report.isMotion = (report.motion & 0x80) != 0; + report.isOnSurface = (report.motion & 0x08) == 0; + report.dx |= (report.mdx << 8); + report.dx = report.dx * -1; + report.dy |= (report.mdy << 8); + report.dy = report.dy * -1; - if (data.motion & 0b111) { // panic recovery, sometimes burst mode works weird. - _inBurst = false; - } - - return data; + return report; } diff --git a/drivers/sensors/pmw3360.h b/drivers/sensors/pmw3360.h index 9aa8e13f8e..4e17aa0c46 100644 --- a/drivers/sensors/pmw3360.h +++ b/drivers/sensors/pmw3360.h @@ -19,8 +19,6 @@ #pragma once #include <stdint.h> -#include "report.h" -#include "spi_master.h" #ifndef PMW3360_CPI # define PMW3360_CPI 1600 @@ -58,21 +56,6 @@ # error "No chip select pin defined -- missing PMW3360_CS_PIN" #endif -/* -The pmw33660 and pmw3389 use the same registers and timing and such. -The only differences between the two is the firmware used, and the -range for the DPI. So add a semi-secret hack to allow use of the -pmw3389's firmware blob. Also, can set the max cpi range too. -This should work for the 3390 and 3391 too, in theory. -*/ -#ifndef PMW3360_FIRMWARE_H -# define PMW3360_FIRMWARE_H "pmw3360_firmware.h" -#endif - -#ifdef CONSOLE_ENABLE -void print_byte(uint8_t byte); -#endif - typedef struct { int8_t motion; bool isMotion; // True if a motion is detected. @@ -83,16 +66,10 @@ typedef struct { int8_t mdy; } report_pmw3360_t; -bool spi_start_adv(void); -void spi_stop_adv(void); -spi_status_t spi_write_adv(uint8_t reg_addr, uint8_t data); -uint8_t spi_read_adv(uint8_t reg_addr); -bool pmw3360_init(void); -void pmw3360_set_cpi(uint16_t cpi); -uint16_t pmw3360_get_cpi(void); -void pmw3360_upload_firmware(void); -bool pmw3360_check_signature(void); +bool pmw3360_init(void); +void pmw3360_upload_firmware(void); +bool pmw3360_check_signature(void); +uint16_t pmw3360_get_cpi(void); +void pmw3360_set_cpi(uint16_t cpi); +/* Reads and clears the current delta values on the sensor */ report_pmw3360_t pmw3360_read_burst(void); - -#define degToRad(angleInDegrees) ((angleInDegrees)*M_PI / 180.0) -#define radToDeg(angleInRadians) ((angleInRadians)*180.0 / M_PI) diff --git a/drivers/sensors/pmw3389.c b/drivers/sensors/pmw3389.c new file mode 100644 index 0000000000..11056bb89e --- /dev/null +++ b/drivers/sensors/pmw3389.c @@ -0,0 +1,296 @@ +/* Copyright 2020 Christopher Courtney, aka Drashna Jael're (@drashna) <drashna@live.com> + * Copyright 2019 Sunjun Kim + * Copyright 2020 Ploopy Corporation + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ + +#include "spi_master.h" +#include "pmw3389.h" +#include "wait.h" +#include "debug.h" +#include "print.h" +#include "pmw3389_firmware.h" + +// Registers +// clang-format off +#define REG_Product_ID 0x00 +#define REG_Revision_ID 0x01 +#define REG_Motion 0x02 +#define REG_Delta_X_L 0x03 +#define REG_Delta_X_H 0x04 +#define REG_Delta_Y_L 0x05 +#define REG_Delta_Y_H 0x06 +#define REG_SQUAL 0x07 +#define REG_RawData_Sum 0x08 +#define REG_Maximum_RawData 0x09 +#define REG_Minimum_RawData 0x0a +#define REG_Shutter_Lower 0x0b +#define REG_Shutter_Upper 0x0c +#define REG_Ripple_Control 0x0d +#define REG_Resolution_L 0x0e +#define REG_Resolution_H 0x0f +#define REG_Config2 0x10 +#define REG_Angle_Tune 0x11 +#define REG_Frame_Capture 0x12 +#define REG_SROM_Enable 0x13 +#define REG_Run_Downshift 0x14 +#define REG_Rest1_Rate_Lower 0x15 +#define REG_Rest1_Rate_Upper 0x16 +#define REG_Rest1_Downshift 0x17 +#define REG_Rest2_Rate_Lower 0x18 +#define REG_Rest2_Rate_Upper 0x19 +#define REG_Rest2_Downshift 0x1a +#define REG_Rest3_Rate_Lower 0x1b +#define REG_Rest3_Rate_Upper 0x1c +#define REG_Observation 0x24 +#define REG_Data_Out_Lower 0x25 +#define REG_Data_Out_Upper 0x26 +#define REG_SROM_ID 0x2a +#define REG_Min_SQ_Run 0x2b +#define REG_RawData_Threshold 0x2c +#define REG_Control2 0x2d +#define REG_Config5_L 0x2e +#define REG_Config5_H 0x2f +#define REG_Power_Up_Reset 0X3a +#define REG_Shutdown 0x3b +#define REG_Inverse_Product_ID 0x3f +#define REG_LiftCutoff_Cal3 0x41 +#define REG_Angle_Snap 0x42 +#define REG_LiftCutoff_Cal1 0x4a +#define REG_Motion_Burst 0x50 +#define REG_SROM_Load_Burst 0x62 +#define REG_Lift_Config 0x63 +#define REG_RawData_Burst 0x64 +#define REG_LiftCutoff_Cal2 0x65 +#define REG_LiftCutoff_Cal_Timeout 0x71 +#define REG_LiftCutoff_Cal_Min_Length 0x72 +#define REG_PWM_Period_Cnt 0x73 +#define REG_PWM_Width_Cnt 0x74 + +#define CPI_STEP 50 +// clang-format on + +// limits to 0--319, resulting in a CPI range of 50 -- 16000 (as only steps of 50 are possible). +#ifndef MAX_CPI +# define MAX_CPI 0x013f +#endif + +bool _inBurst = false; + +#ifdef CONSOLE_ENABLE +void print_byte(uint8_t byte) { dprintf("%c%c%c%c%c%c%c%c|", (byte & 0x80 ? '1' : '0'), (byte & 0x40 ? '1' : '0'), (byte & 0x20 ? '1' : '0'), (byte & 0x10 ? '1' : '0'), (byte & 0x08 ? '1' : '0'), (byte & 0x04 ? '1' : '0'), (byte & 0x02 ? '1' : '0'), (byte & 0x01 ? '1' : '0')); } +#endif +#define constrain(amt, low, high) ((amt) < (low) ? (low) : ((amt) > (high) ? (high) : (amt))) + +bool pmw3389_spi_start(void) { + bool status = spi_start(PMW3389_CS_PIN, PMW3389_SPI_LSBFIRST, PMW3389_SPI_MODE, PMW3389_SPI_DIVISOR); + // tNCS-SCLK, 120ns + wait_us(1); + return status; +} + +spi_status_t pmw3389_write(uint8_t reg_addr, uint8_t data) { + pmw3389_spi_start(); + + if (reg_addr != REG_Motion_Burst) { + _inBurst = false; + } + + // send address of the register, with MSBit = 1 to indicate it's a write + spi_status_t status = spi_write(reg_addr | 0x80); + status = spi_write(data); + + // tSCLK-NCS for write operation is 35 us + wait_us(35); + spi_stop(); + + // tSWW/tSWR (=180us) minus tSCLK-NCS. Could be shortened, but is looks like a safe lower bound + wait_us(145); + return status; +} + +uint8_t pmw3389_read(uint8_t reg_addr) { + pmw3389_spi_start(); + // send adress of the register, with MSBit = 0 to indicate it's a read + spi_write(reg_addr & 0x7f); + // tSRAD (=160us) + wait_us(160); + uint8_t data = spi_read(); + + // tSCLK-NCS, 120ns + wait_us(1); + spi_stop(); + + // tSRW/tSRR (=20us) minus tSCLK-NCS + wait_us(19); + return data; +} + +bool pmw3389_init(void) { + setPinOutput(PMW3389_CS_PIN); + + spi_init(); + _inBurst = false; + + spi_stop(); + pmw3389_spi_start(); + spi_stop(); + + pmw3389_write(REG_Shutdown, 0xb6); // Shutdown first + wait_ms(300); + + pmw3389_spi_start(); + wait_us(40); + spi_stop(); + wait_us(40); + + // power up, need to first drive NCS high then low, see above. + pmw3389_write(REG_Power_Up_Reset, 0x5a); + wait_ms(50); + + // read registers and discard + pmw3389_read(REG_Motion); + pmw3389_read(REG_Delta_X_L); + pmw3389_read(REG_Delta_X_H); + pmw3389_read(REG_Delta_Y_L); + pmw3389_read(REG_Delta_Y_H); + + pmw3389_upload_firmware(); + + spi_stop(); + + wait_ms(10); + pmw3389_set_cpi(PMW3389_CPI); + + wait_ms(1); + + pmw3389_write(REG_Config2, 0x00); + + pmw3389_write(REG_Angle_Tune, constrain(ROTATIONAL_TRANSFORM_ANGLE, -127, 127)); + + pmw3389_write(REG_Lift_Config, PMW3389_LIFTOFF_DISTANCE); + + bool init_success = pmw3389_check_signature(); +#ifdef CONSOLE_ENABLE + if (init_success) { + dprintf("pmw3389 signature verified"); + } else { + dprintf("pmw3389 signature verification failed!"); + } +#endif + + writePinLow(PMW3389_CS_PIN); + + return init_success; +} + +void pmw3389_upload_firmware(void) { + // Datasheet claims we need to disable REST mode first, but during startup + // it's already disabled and we're not turning it on ... + // pmw3389_write(REG_Config2, 0x00); // disable REST mode + pmw3389_write(REG_SROM_Enable, 0x1d); + + wait_ms(10); + + pmw3389_write(REG_SROM_Enable, 0x18); + + pmw3389_spi_start(); + spi_write(REG_SROM_Load_Burst | 0x80); + wait_us(15); + +#ifdef PMW3389_LEGACY_FIRMWARE_UPLOAD + unsigned char c; + for (int i = 0; i < FIRMWARE_LENGTH; i++) { + c = (unsigned char)pgm_read_byte(firmware_data + i); + spi_write(c); + wait_us(15); + } +#else + spi_transmit(firmware_data, sizeof(firmware_data)); +#endif + wait_us(200); + + pmw3389_read(REG_SROM_ID); + pmw3389_write(REG_Config2, 0x00); +} + +bool pmw3389_check_signature(void) { + uint8_t pid = pmw3389_read(REG_Product_ID); + uint8_t iv_pid = pmw3389_read(REG_Inverse_Product_ID); + uint8_t SROM_ver = pmw3389_read(REG_SROM_ID); + return (pid == firmware_signature[0] && iv_pid == firmware_signature[1] && SROM_ver == firmware_signature[2]); // signature for SROM 0x04 +} + +uint16_t pmw3389_get_cpi(void) { + uint16_t cpival = (pmw3389_read(REG_Resolution_H) << 8) | pmw3389_read(REG_Resolution_L); + return (uint16_t)((cpival + 1) & 0xffff) * CPI_STEP; +} + +void pmw3389_set_cpi(uint16_t cpi) { + uint16_t cpival = constrain((cpi / CPI_STEP) - 1, 0, MAX_CPI); + // Sets upper byte first for more consistent setting of cpi + pmw3389_write(REG_Resolution_H, (cpival >> 8) & 0xff); + pmw3389_write(REG_Resolution_L, cpival & 0xff); +} + +report_pmw3389_t pmw3389_read_burst(void) { + report_pmw3389_t report = {0}; + + if (!_inBurst) { +#ifdef CONSOLE_ENABLE + dprintf("burst on"); +#endif + pmw3389_write(REG_Motion_Burst, 0x00); + _inBurst = true; + } + + pmw3389_spi_start(); + spi_write(REG_Motion_Burst); + wait_us(35); // waits for tSRAD_MOTBR + + report.motion = spi_read(); + spi_read(); // skip Observation + // delta registers + report.dx = spi_read(); + report.mdx = spi_read(); + report.dy = spi_read(); + report.mdy = spi_read(); + + if (report.motion & 0b111) { // panic recovery, sometimes burst mode works weird. + _inBurst = false; + } + + spi_stop(); + +#ifdef CONSOLE_ENABLE + if (debug_mouse) { + print_byte(report.motion); + print_byte(report.dx); + print_byte(report.mdx); + print_byte(report.dy); + print_byte(report.mdy); + dprintf("\n"); + } +#endif + + report.isMotion = (report.motion & 0x80) != 0; + report.isOnSurface = (report.motion & 0x08) == 0; + report.dx |= (report.mdx << 8); + report.dx = report.dx * -1; + report.dy |= (report.mdy << 8); + report.dy = report.dy * -1; + + return report; +} diff --git a/drivers/sensors/pmw3389.h b/drivers/sensors/pmw3389.h new file mode 100644 index 0000000000..a7c95e6076 --- /dev/null +++ b/drivers/sensors/pmw3389.h @@ -0,0 +1,76 @@ +/* Copyright 2021 Alabastard (@Alabastard-64) + * Copyright 2020 Christopher Courtney, aka Drashna Jael're (@drashna) <drashna@live.com> + * Copyright 2019 Sunjun Kim + * Copyright 2020 Ploopy Corporation + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ + +#pragma once + +#include <stdint.h> + +#ifndef PMW3389_CPI +# define PMW3389_CPI 2000 +#endif + +#ifndef PMW3389_CLOCK_SPEED +# define PMW3389_CLOCK_SPEED 2000000 +#endif + +#ifndef PMW3389_SPI_LSBFIRST +# define PMW3389_SPI_LSBFIRST false +#endif + +#ifndef PMW3389_SPI_MODE +# define PMW3389_SPI_MODE 3 +#endif + +#ifndef PMW3389_SPI_DIVISOR +# ifdef __AVR__ +# define PMW3389_SPI_DIVISOR (F_CPU / PMW3389_CLOCK_SPEED) +# else +# define PMW3389_SPI_DIVISOR 64 +# endif +#endif + +#ifndef PMW3389_LIFTOFF_DISTANCE +# define PMW3389_LIFTOFF_DISTANCE 0x02 +#endif + +#ifndef ROTATIONAL_TRANSFORM_ANGLE +# define ROTATIONAL_TRANSFORM_ANGLE 0x00 +#endif + +#ifndef PMW3389_CS_PIN +# error "No chip select pin defined -- missing PMW3389_CS_PIN" +#endif + +typedef struct { + int8_t motion; + bool isMotion; // True if a motion is detected. + bool isOnSurface; // True when a chip is on a surface + int16_t dx; // displacement on x directions. Unit: Count. (CPI * Count = Inch value) + int8_t mdx; + int16_t dy; // displacement on y directions. + int8_t mdy; +} report_pmw3389_t; + +bool pmw3389_init(void); +void pmw3389_upload_firmware(void); +bool pmw3389_check_signature(void); +uint16_t pmw3389_get_cpi(void); +void pmw3389_set_cpi(uint16_t cpi); +/* Reads and clears the current delta values on the sensor */ +report_pmw3389_t pmw3389_read_burst(void); diff --git a/drivers/sensors/pmw3389_firmware.h b/drivers/sensors/pmw3389_firmware.h index 0564dab73a..cd9638b605 100644 --- a/drivers/sensors/pmw3389_firmware.h +++ b/drivers/sensors/pmw3389_firmware.h @@ -18,286 +18,290 @@ #pragma once +#include "progmem.h" + // PID, Inverse PID, SROM version const uint8_t firmware_signature[] PROGMEM = {0x42, 0xBD, 0x04}; +#define FIRMWARE_LENGTH 4094 + +// Firmware Blob for PMW3389 + // clang-format off -// Firmware Blob foor PMW3389 -const uint16_t firmware_length = 4094; -// clang-format off -const uint8_t firmware_data[] PROGMEM = { // SROM 0x04 -0x01, 0xe8, 0xba, 0x26, 0x0b, 0xb2, 0xbe, 0xfe, 0x7e, 0x5f, 0x3c, 0xdb, 0x15, 0xa8, 0xb3, -0xe4, 0x2b, 0xb5, 0xe8, 0x53, 0x07, 0x6d, 0x3b, 0xd1, 0x20, 0xc2, 0x06, 0x6f, 0x3d, 0xd9, -0x11, 0xa0, 0xc2, 0xe7, 0x2d, 0xb9, 0xd1, 0x20, 0xa3, 0xa5, 0xc8, 0xf3, 0x64, 0x4a, 0xf7, -0x4d, 0x18, 0x93, 0xa4, 0xca, 0xf7, 0x6c, 0x5a, 0x36, 0xee, 0x5e, 0x3e, 0xfe, 0x7e, 0x7e, -0x5f, 0x1d, 0x99, 0xb0, 0xc3, 0xe5, 0x29, 0xd3, 0x03, 0x65, 0x48, 0x12, 0x87, 0x6d, 0x58, -0x32, 0xe6, 0x2f, 0xdc, 0x3a, 0xf2, 0x4f, 0xfd, 0x59, 0x11, 0x81, 0x61, 0x21, 0xc0, 0x02, -0x86, 0x8e, 0x7f, 0x5d, 0x38, 0xf2, 0x47, 0x0c, 0x7b, 0x55, 0x28, 0xb3, 0xe4, 0x4a, 0x16, -0xab, 0xbf, 0xdd, 0x38, 0xf2, 0x66, 0x4e, 0xff, 0x5d, 0x19, 0x91, 0xa0, 0xa3, 0xa5, 0xc8, -0x12, 0xa6, 0xaf, 0xdc, 0x3a, 0xd1, 0x41, 0x60, 0x75, 0x58, 0x24, 0x92, 0xd4, 0x72, 0x6c, -0xe0, 0x2f, 0xfd, 0x23, 0x8d, 0x1c, 0x5b, 0xb2, 0x97, 0x36, 0x3d, 0x0b, 0xa2, 0x49, 0xb1, -0x58, 0xf2, 0x1f, 0xc0, 0xcb, 0xf8, 0x41, 0x4f, 0xcd, 0x1e, 0x6b, 0x39, 0xa7, 0x2b, 0xe9, -0x30, 0x16, 0x83, 0xd2, 0x0e, 0x47, 0x8f, 0xe3, 0xb1, 0xdf, 0xa2, 0x15, 0xdb, 0x5d, 0x30, -0xc5, 0x1a, 0xab, 0x31, 0x99, 0xf3, 0xfa, 0xb2, 0x86, 0x69, 0xad, 0x7a, 0xe8, 0xa7, 0x18, -0x6a, 0xcc, 0xc8, 0x65, 0x23, 0x87, 0xa8, 0x5f, 0xf5, 0 |