19 files changed, 1586 insertions, 0 deletions
diff --git a/drivers/painter/comms/qp_comms_spi.c b/drivers/painter/comms/qp_comms_spi.c
new file mode 100644
index 0000000000..e644ba9f84
--- /dev/null
+++ b/drivers/painter/comms/qp_comms_spi.c
@@ -0,0 +1,137 @@
+// Copyright 2021 Nick Brassel (@tzarc)
+// SPDX-License-Identifier: GPL-2.0-or-later
+
+#ifdef QUANTUM_PAINTER_SPI_ENABLE
+
+#    include "spi_master.h"
+#    include "qp_comms_spi.h"
+
+////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
+// Base SPI support
+
+bool qp_comms_spi_init(painter_device_t device) {
+    struct painter_driver_t *     driver       = (struct painter_driver_t *)device;
+    struct qp_comms_spi_config_t *comms_config = (struct qp_comms_spi_config_t *)driver->comms_config;
+
+    // Initialize the SPI peripheral
+    spi_init();
+
+    // Set up CS as output high
+    setPinOutput(comms_config->chip_select_pin);
+    writePinHigh(comms_config->chip_select_pin);
+
+    return true;
+}
+
+bool qp_comms_spi_start(painter_device_t device) {
+    struct painter_driver_t *     driver       = (struct painter_driver_t *)device;
+    struct qp_comms_spi_config_t *comms_config = (struct qp_comms_spi_config_t *)driver->comms_config;
+
+    return spi_start(comms_config->chip_select_pin, comms_config->lsb_first, comms_config->mode, comms_config->divisor);
+}
+
+uint32_t qp_comms_spi_send_data(painter_device_t device, const void *data, uint32_t byte_count) {
+    uint32_t       bytes_remaining = byte_count;
+    const uint8_t *p               = (const uint8_t *)data;
+    while (bytes_remaining > 0) {
+        uint32_t bytes_this_loop = bytes_remaining < 1024 ? bytes_remaining : 1024;
+        spi_transmit(p, bytes_this_loop);
+        p += bytes_this_loop;
+        bytes_remaining -= bytes_this_loop;
+    }
+
+    return byte_count - bytes_remaining;
+}
+
+void qp_comms_spi_stop(painter_device_t device) {
+    struct painter_driver_t *     driver       = (struct painter_driver_t *)device;
+    struct qp_comms_spi_config_t *comms_config = (struct qp_comms_spi_config_t *)driver->comms_config;
+    spi_stop();
+    writePinHigh(comms_config->chip_select_pin);
+}
+
+const struct painter_comms_vtable_t spi_comms_vtable = {
+    .comms_init  = qp_comms_spi_init,
+    .comms_start = qp_comms_spi_start,
+    .comms_send  = qp_comms_spi_send_data,
+    .comms_stop  = qp_comms_spi_stop,
+};
+
+////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
+// SPI with D/C and RST pins
+
+#    ifdef QUANTUM_PAINTER_SPI_DC_RESET_ENABLE
+
+bool qp_comms_spi_dc_reset_init(painter_device_t device) {
+    if (!qp_comms_spi_init(device)) {
+        return false;
+    }
+
+    struct painter_driver_t *              driver       = (struct painter_driver_t *)device;
+    struct qp_comms_spi_dc_reset_config_t *comms_config = (struct qp_comms_spi_dc_reset_config_t *)driver->comms_config;
+
+    // Set up D/C as output low, if specified
+    if (comms_config->dc_pin != NO_PIN) {
+        setPinOutput(comms_config->dc_pin);
+        writePinLow(comms_config->dc_pin);
+    }
+
+    // Set up RST as output, if specified, performing a reset in the process
+    if (comms_config->reset_pin != NO_PIN) {
+        setPinOutput(comms_config->reset_pin);
+        writePinLow(comms_config->reset_pin);
+        wait_ms(20);
+        writePinHigh(comms_config->reset_pin);
+        wait_ms(20);
+    }
+
+    return true;
+}
+
+uint32_t qp_comms_spi_dc_reset_send_data(painter_device_t device, const void *data, uint32_t byte_count) {
+    struct painter_driver_t *              driver       = (struct painter_driver_t *)device;
+    struct qp_comms_spi_dc_reset_config_t *comms_config = (struct qp_comms_spi_dc_reset_config_t *)driver->comms_config;
+    writePinHigh(comms_config->dc_pin);
+    return qp_comms_spi_send_data(device, data, byte_count);
+}
+
+void qp_comms_spi_dc_reset_send_command(painter_device_t device, uint8_t cmd) {
+    struct painter_driver_t *              driver       = (struct painter_driver_t *)device;
+    struct qp_comms_spi_dc_reset_config_t *comms_config = (struct qp_comms_spi_dc_reset_config_t *)driver->comms_config;
+    writePinLow(comms_config->dc_pin);
+    spi_write(cmd);
+}
+
+void qp_comms_spi_dc_reset_bulk_command_sequence(painter_device_t device, const uint8_t *sequence, size_t sequence_len) {
+    for (size_t i = 0; i < sequence_len;) {
+        uint8_t command   = sequence[i];
+        uint8_t delay     = sequence[i + 1];
+        uint8_t num_bytes = sequence[i + 2];
+        qp_comms_spi_dc_reset_send_command(device, command);
+        if (num_bytes > 0) {
+            qp_comms_spi_dc_reset_send_data(device, &sequence[i + 3], num_bytes);
+        }
+        if (delay > 0) {
+            wait_ms(delay);
+        }
+        i += (3 + num_bytes);
+    }
+}
+
+const struct painter_comms_with_command_vtable_t spi_comms_with_dc_vtable = {
+    .base =
+        {
+            .comms_init  = qp_comms_spi_dc_reset_init,
+            .comms_start = qp_comms_spi_start,
+            .comms_send  = qp_comms_spi_dc_reset_send_data,
+            .comms_stop  = qp_comms_spi_stop,
+        },
+    .send_command          = qp_comms_spi_dc_reset_send_command,
+    .bulk_command_sequence = qp_comms_spi_dc_reset_bulk_command_sequence,
+};
+
+#    endif // QUANTUM_PAINTER_SPI_DC_RESET_ENABLE
+
+////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
+
+#endif // QUANTUM_PAINTER_SPI_ENABLE
diff --git a/drivers/painter/comms/qp_comms_spi.h b/drivers/painter/comms/qp_comms_spi.h
new file mode 100644
index 0000000000..9989987327
--- /dev/null
+++ b/drivers/painter/comms/qp_comms_spi.h
@@ -0,0 +1,51 @@
+// Copyright 2021 Nick Brassel (@tzarc)
+// SPDX-License-Identifier: GPL-2.0-or-later
+
+#pragma once
+
+#ifdef QUANTUM_PAINTER_SPI_ENABLE
+
+#    include <stdint.h>
+
+#    include "gpio.h"
+#    include "qp_internal.h"
+
+////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
+// Base SPI support
+
+struct qp_comms_spi_config_t {
+    pin_t    chip_select_pin;
+    uint16_t divisor;
+    bool     lsb_first;
+    int8_t   mode;
+};
+
+bool     qp_comms_spi_init(painter_device_t device);
+bool     qp_comms_spi_start(painter_device_t device);
+uint32_t qp_comms_spi_send_data(painter_device_t device, const void* data, uint32_t byte_count);
+void     qp_comms_spi_stop(painter_device_t device);
+
+extern const struct painter_comms_vtable_t spi_comms_vtable;
+
+////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
+// SPI with D/C and RST pins
+
+#    ifdef QUANTUM_PAINTER_SPI_DC_RESET_ENABLE
+
+struct qp_comms_spi_dc_reset_config_t {
+    struct qp_comms_spi_config_t spi_config;
+    pin_t                        dc_pin;
+    pin_t                        reset_pin;
+};
+
+void     qp_comms_spi_dc_reset_send_command(painter_device_t device, uint8_t cmd);
+uint32_t qp_comms_spi_dc_reset_send_data(painter_device_t device, const void* data, uint32_t byte_count);
+void     qp_comms_spi_dc_reset_bulk_command_sequence(painter_device_t device, const uint8_t* sequence, size_t sequence_len);
+
+extern const struct painter_comms_with_command_vtable_t spi_comms_with_dc_vtable;
+
+#    endif // QUANTUM_PAINTER_SPI_DC_RESET_ENABLE
+
+////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
+
+#endif // QUANTUM_PAINTER_SPI_ENABLE
diff --git a/drivers/painter/gc9a01/qp_gc9a01.c b/drivers/painter/gc9a01/qp_gc9a01.c
new file mode 100644
index 0000000000..ad76d58b07
--- /dev/null
+++ b/drivers/painter/gc9a01/qp_gc9a01.c
@@ -0,0 +1,150 @@
+// Copyright 2021 Paul Cotter (@gr1mr3aver)
+// SPDX-License-Identifier: GPL-2.0-or-later
+
+#include <wait.h>
+#include "qp_internal.h"
+#include "qp_comms.h"
+#include "qp_gc9a01.h"
+#include "qp_gc9a01_opcodes.h"
+#include "qp_tft_panel.h"
+
+////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
+// Driver storage
+////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
+
+tft_panel_dc_reset_painter_device_t gc9a01_drivers[GC9A01_NUM_DEVICES] = {0};
+
+////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
+// Initialization
+////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
+bool qp_gc9a01_init(painter_device_t device, painter_rotation_t rotation) {
+    // A lot of these "unknown" opcodes are sourced from other OSS projects and are seemingly required for this display to function.
+    // clang-format off
+    const uint8_t gc9a01_init_sequence[] = {
+        // Command,                 Delay,  N, Data[N]
+        GC9A01_SET_INTER_REG_ENABLE2,   0,  0,
+        0xEB,                           0,  1, 0x14,
+        GC9A01_SET_INTER_REG_ENABLE1,   0,  0,
+        GC9A01_SET_INTER_REG_ENABLE2,   0,  0,
+        0xEB,                           0,  1, 0x14,
+        0x84,                           0,  1, 0x40,
+        0x85,                           0,  1, 0xFF,
+        0x86,                           0,  1, 0xFF,
+        0x87,                           0,  1, 0xFF,
+        0x88,                           0,  1, 0x0A,
+        0x89,                           0,  1, 0x21,
+        0x8a,                           0,  1, 0x00,
+        0x8b,                           0,  1, 0x80,
+        0x8c,                           0,  1, 0x01,
+        0x8d,                           0,  1, 0x01,
+        0x8e,                           0,  1, 0xFF,
+        0x8f,                           0,  1, 0xFF,
+        GC9A01_SET_FUNCTION_CTL,        0,  2, 0x00, 0x20,
+        GC9A01_SET_PIX_FMT,             0,  1, 0x55,
+        0x90,                           0,  4, 0x08, 0x08, 0x08, 0x08,
+        0xBD,                           0,  1, 0x06,
+        0xBC,                           0,  1, 0x00,
+        0xFF,                           0,  3, 0x60, 0x01, 0x04,
+        GC9A01_SET_POWER_CTL_2,         0,  1, 0x13,
+        GC9A01_SET_POWER_CTL_3,         0,  1, 0x13,
+        GC9A01_SET_POWER_CTL_4,         0,  1, 0x22,
+        0xBE,                           0,  1, 0x11,
+        0xE1,                           0,  2, 0x10, 0x0E,
+        0xDF,                           0,  3, 0x21, 0x0C, 0x02,
+        GC9A01_SET_GAMMA1,              0,  6, 0x45, 0x09, 0x08, 0x08, 0x26, 0x2A,
+        GC9A01_SET_GAMMA2,              0,  6, 0x43, 0x70, 0x72, 0x36, 0x37, 0x6F,
+        GC9A01_SET_GAMMA3,              0,  6, 0x45, 0x09, 0x08, 0x08, 0x26, 0x2A,
+        GC9A01_SET_GAMMA4,              0,  6, 0x43, 0x70, 0x72, 0x36, 0x37, 0x6F,
+        0xED,                           0,  2, 0x1B, 0x0B,
+        0xAE,                           0,  1, 0x77,
+        0xCD,                           0,  1, 0x63,
+        0x70,                           0,  9, 0x07, 0x07, 0x04, 0x0E, 0x0F, 0x09, 0x07, 0x08, 0x03,
+        GC9A01_SET_FRAME_RATE,          0,  1, 0x34,
+        0x62,                           0, 12, 0x18, 0x0D, 0x71, 0xED, 0x70, 0x70, 0x18, 0x0F, 0x71, 0xEF, 0x70, 0x70,
+        0x63,                           0, 12, 0x18, 0x11, 0x71, 0xF1, 0x70, 0x70, 0x18, 0x13, 0x71, 0xF3, 0x70, 0x70,
+        0x64,                           0,  7, 0x28, 0x29, 0xF1, 0x01, 0xF1, 0x00, 0x07,
+        0x66,                           0, 10, 0x3C, 0x00, 0xCD, 0x67, 0x45, 0x45, 0x10, 0x00, 0x00, 0x00,
+        0x67,                           0, 10, 0x00, 0x3C, 0x00, 0x00, 0x00, 0x01, 0x54, 0x10, 0x32, 0x98,
+        0x74,                           0,  7, 0x10, 0x85, 0x80, 0x00, 0x00, 0x4E, 0x00,
+        0x98,                           0,  2, 0x3E, 0x07,
+        GC9A01_CMD_TEARING_OFF,         0,  0,
+        GC9A01_CMD_INVERT_OFF,          0,  0,
+        GC9A01_CMD_SLEEP_OFF,         120,  0,
+        GC9A01_CMD_DISPLAY_ON,         20,  0
+    };
+    // clang-format on
+
+    // clang-format on
+    qp_comms_bulk_command_sequence(device, gc9a01_init_sequence, sizeof(gc9a01_init_sequence));
+
+    // Configure the rotation (i.e. the ordering and direction of memory writes in GRAM)
+    const uint8_t madctl[] = {
+        [QP_ROTATION_0]   = GC9A01_MADCTL_BGR,
+        [QP_ROTATION_90]  = GC9A01_MADCTL_BGR | GC9A01_MADCTL_MX | GC9A01_MADCTL_MV,
+        [QP_ROTATION_180] = GC9A01_MADCTL_BGR | GC9A01_MADCTL_MX | GC9A01_MADCTL_MY,
+        [QP_ROTATION_270] = GC9A01_MADCTL_BGR | GC9A01_MADCTL_MV | GC9A01_MADCTL_MY,
+    };
+    qp_comms_command_databyte(device, GC9A01_SET_MEM_ACS_CTL, madctl[rotation]);
+
+    return true;
+}
+
+////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
+// Driver vtable
+////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
+
+const struct tft_panel_dc_reset_painter_driver_vtable_t gc9a01_driver_vtable = {
+    .base =
+        {
+            .init            = qp_gc9a01_init,
+            .power           = qp_tft_panel_power,
+            .clear           = qp_tft_panel_clear,
+            .flush           = qp_tft_panel_flush,
+            .pixdata         = qp_tft_panel_pixdata,
+            .viewport        = qp_tft_panel_viewport,
+            .palette_convert = qp_tft_panel_palette_convert,
+            .append_pixels   = qp_tft_panel_append_pixels,
+        },
+    .rgb888_to_native16bit = qp_rgb888_to_rgb565_swapped,
+    .num_window_bytes      = 2,
+    .swap_window_coords    = false,
+    .opcodes =
+        {
+            .display_on         = GC9A01_CMD_DISPLAY_ON,
+            .display_off        = GC9A01_CMD_DISPLAY_OFF,
+            .set_column_address = GC9A01_SET_COL_ADDR,
+            .set_row_address    = GC9A01_SET_PAGE_ADDR,
+            .enable_writes      = GC9A01_SET_MEM,
+        },
+};
+
+#ifdef QUANTUM_PAINTER_GC9A01_SPI_ENABLE
+// Factory function for creating a handle to the ILI9341 device
+painter_device_t qp_gc9a01_make_spi_device(uint16_t panel_width, uint16_t panel_height, pin_t chip_select_pin, pin_t dc_pin, pin_t reset_pin, uint16_t spi_divisor, int spi_mode) {
+    for (uint32_t i = 0; i < GC9A01_NUM_DEVICES; ++i) {
+        tft_panel_dc_reset_painter_device_t *driver = &gc9a01_drivers[i];
+        if (!driver->base.driver_vtable) {
+            driver->base.driver_vtable         = (const struct painter_driver_vtable_t *)&gc9a01_driver_vtable;
+            driver->base.comms_vtable          = (const struct painter_comms_vtable_t *)&spi_comms_with_dc_vtable;
+            driver->base.native_bits_per_pixel = 16; // RGB565
+            driver->base.panel_width           = panel_width;
+            driver->base.panel_height          = panel_height;
+            driver->base.rotation              = QP_ROTATION_0;
+            driver->base.offset_x              = 0;
+            driver->base.offset_y              = 0;
+
+            // SPI and other pin configuration
+            driver->base.comms_config                              = &driver->spi_dc_reset_config;
+            driver->spi_dc_reset_config.spi_config.chip_select_pin = chip_select_pin;
+            driver->spi_dc_reset_config.spi_config.divisor         = spi_divisor;
+            driver->spi_dc_reset_config.spi_config.lsb_first       = false;
+            driver->spi_dc_reset_config.spi_config.mode            = spi_mode;
+            driver->spi_dc_reset_config.dc_pin                     = dc_pin;
+            driver->spi_dc_reset_config.reset_pin                  = reset_pin;
+            return (painter_device_t)driver;
+        }
+    }
+    return NULL;
+}
+
+#endif // QUANTUM_PAINTER_GC9A01_SPI_ENABLE
diff --git a/drivers/painter/gc9a01/qp_gc9a01.h b/drivers/painter/gc9a01/qp_gc9a01.h
new file mode 100644
index 0000000000..e2b1939564
--- /dev/null
+++ b/drivers/painter/gc9a01/qp_gc9a01.h
@@ -0,0 +1,37 @@
+// Copyright 2021 Paul Cotter (@gr1mr3aver)
+// SPDX-License-Identifier: GPL-2.0-or-later
+
+#pragma once
+
+#include "gpio.h"
+#include "qp_internal.h"
+
+////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
+// Quantum Painter GC9A01 configurables (add to your keyboard's config.h)
+
+#ifndef GC9A01_NUM_DEVICES
+/**
+ * @def This controls the maximum number of GC9A01 devices that Quantum Painter can communicate with at any one time.
+ *      Increasing this number allows for multiple displays to be used.
+ */
+#    define GC9A01_NUM_DEVICES 1
+#endif
+
+////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
+// Quantum Painter GC9A01 device factories
+
+#ifdef QUANTUM_PAINTER_GC9A01_SPI_ENABLE
+/**
+ * Factory method for an GC9A01 SPI LCD device.
+ *
+ * @param panel_width[in] the width of the display panel
+ * @param panel_height[in] the height of the display panel
+ * @param chip_select_pin[in] the GPIO pin used for SPI chip select
+ * @param dc_pin[in] the GPIO pin used for D/C control
+ * @param reset_pin[in] the GPIO pin used for RST
+ * @param spi_divisor[in] the SPI divisor to use when communicating with the display
+ * @param spi_mode[in] the SPI mode to use when communicating with the display
+ * @return the device handle used with all drawing routines in Quantum Painter
+ */
+painter_device_t qp_gc9a01_make_spi_device(uint16_t panel_width, uint16_t panel_height, pin_t chip_select_pin, pin_t dc_pin, pin_t reset_pin, uint16_t spi_divisor, int spi_mode);
+#endif // QUANTUM_PAINTER_GC9A01_SPI_ENABLE
diff --git a/drivers/painter/gc9a01/qp_gc9a01_opcodes.h b/drivers/painter/gc9a01/qp_gc9a01_opcodes.h
new file mode 100644
index 0000000000..6ff4efe7a8
--- /dev/null
+++ b/drivers/painter/gc9a01/qp_gc9a01_opcodes.h
@@ -0,0 +1,78 @@
+// Copyright 2021 Paul Cotter (@gr1mr3aver)
+// SPDX-License-Identifier: GPL-2.0-or-later
+
+#pragma once
+
+////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
+// Quantum Painter GC9A01 command opcodes
+////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
+
+////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
+// Level 1 command opcodes
+
+#define GC9A01_GET_ID_INFO 0x04       // Get ID information
+#define GC9A01_GET_STATUS 0x09        // Get status
+#define GC9A01_CMD_SLEEP_ON 0x10      // Enter sleep mode
+#define GC9A01_CMD_SLEEP_OFF 0x11     // Exit sleep mode
+#define GC9A01_CMD_PARTIAL_ON 0x12    // Enter partial mode
+#define GC9A01_CMD_PARTIAL_OFF 0x13   // Exit partial mode
+#define GC9A01_CMD_INVERT_ON 0x20     // Enter inverted mode
+#define GC9A01_CMD_INVERT_OFF 0x21    // Exit inverted mode
+#define GC9A01_CMD_DISPLAY_OFF 0x28   // Disable display
+#define GC9A01_CMD_DISPLAY_ON 0x29    // Enable display
+#define GC9A01_SET_COL_ADDR 0x2A      // Set column address
+#define GC9A01_SET_PAGE_ADDR 0x2B     // Set page address
+#define GC9A01_SET_MEM 0x2C           // Set memory
+#define GC9A01_SET_PARTIAL_AREA 0x30  // Set partial area
+#define GC9A01_SET_VSCROLL 0x33       // Set vertical scroll def
+#define GC9A01_CMD_TEARING_ON 0x34    // Tearing line enabled
+#define GC9A01_CMD_TEARING_OFF 0x35   // Tearing line disabled
+#define GC9A01_SET_MEM_ACS_CTL 0x36   // Set mem access ctl
+#define GC9A01_SET_VSCROLL_ADDR 0x37  // Set vscroll start addr
+#define GC9A01_CMD_IDLE_OFF 0x38      // Exit idle mode
+#define GC9A01_CMD_IDLE_ON 0x39       // Enter idle mode
+#define GC9A01_SET_PIX_FMT 0x3A       // Set pixel format
+#define GC9A01_SET_MEM_CONT 0x3C      // Set memory continue
+#define GC9A01_SET_TEAR_SCANLINE 0x44 // Set tearing scanline
+#define GC9A01_GET_TEAR_SCANLINE 0x45 // Get tearing scanline
+#define GC9A01_SET_BRIGHTNESS 0x51    // Set brightness
+#define GC9A01_SET_DISPLAY_CTL 0x53   // Set display ctl
+#define GC9A01_GET_ID1 0xDA           // Get ID1
+#define GC9A01_GET_ID2 0xDB           // Get ID2
+#define GC9A01_GET_ID3 0xDC           // Get ID3
+
+////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
+// Level 2 command opcodes
+
+#define GC9A01_SET_RGB_IF_SIG_CTL 0xB0     // RGB IF signal ctl
+#define GC9A01_SET_BLANKING_PORCH_CTL 0xB5 // Set blanking porch ctl
+#define GC9A01_SET_FUNCTION_CTL 0xB6       // Set function ctl
+#define GC9A01_SET_TEARING_EFFECT 0xBA     // Set backlight ctl 3
+#define GC9A01_SET_IF_CTL 0xF6             // Set interface control
+
+////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
+// Level 3 command opcodes
+
+#define GC9A01_SET_FRAME_RATE 0xE8        // Set frame rate
+#define GC9A01_SET_SPI_2DATA 0xE9         // Set frame rate
+#define GC9A01_SET_POWER_CTL_1 0xC1       // Set power ctl 1
+#define GC9A01_SET_POWER_CTL_2 0xC3       // Set power ctl 2
+#define GC9A01_SET_POWER_CTL_3 0xC4       // Set power ctl 3
+#define GC9A01_SET_POWER_CTL_4 0xC9       // Set power ctl 4
+#define GC9A01_SET_POWER_CTL_7 0xA7       // Set power ctl 7
+#define GC9A01_SET_INTER_REG_ENABLE1 0xFE // Enable Inter Register 1
+#define GC9A01_SET_INTER_REG_ENABLE2 0xEF // Enable Inter Register 2
+#define GC9A01_SET_GAMMA1 0xF0            //
+#define GC9A01_SET_GAMMA2 0xF1
+#define GC9A01_SET_GAMMA3 0xF2
+#define GC9A01_SET_GAMMA4 0xF3
+
+////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
+// MADCTL Flags
+#define GC9A01_MADCTL_MY 0b10000000
+#define GC9A01_MADCTL_MX 0b01000000
+#define GC9A01_MADCTL_MV 0b00100000
+#define GC9A01_MADCTL_ML 0b00010000
+#define GC9A01_MADCTL_RGB 0b00000000
+#define GC9A01_MADCTL_BGR 0b00001000
+#define GC9A01_MADCTL_MH 0b00000100
diff --git a/drivers/painter/ili9xxx/qp_ili9163.c b/drivers/painter/ili9xxx/qp_ili9163.c
new file mode 100644
index 0000000000..beaac0fbb5
--- /dev/null
+++ b/drivers/painter/ili9xxx/qp_ili9163.c
@@ -0,0 +1,121 @@
+// Copyright 2021 Nick Brassel (@tzarc)
+// SPDX-License-Identifier: GPL-2.0-or-later
+
+#include "qp_internal.h"
+#include "qp_comms.h"
+#include "qp_ili9163.h"
+#include "qp_ili9xxx_opcodes.h"
+#include "qp_tft_panel.h"
+
+#ifdef QUANTUM_PAINTER_ILI9163_SPI_ENABLE
+#    include "qp_comms_spi.h"
+#endif // QUANTUM_PAINTER_ILI9163_SPI_ENABLE
+
+////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
+// Common
+
+// Driver storage
+tft_panel_dc_reset_painter_device_t ili9163_drivers[ILI9163_NUM_DEVICES] = {0};
+
+////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
+// Initialization
+
+bool qp_ili9163_init(painter_device_t device, painter_rotation_t rotation) {
+    // clang-format off
+    const uint8_t ili9163_init_sequence[] = {
+        // Command,                 Delay,  N, Data[N]
+        ILI9XXX_CMD_RESET,            120,  0,
+        ILI9XXX_CMD_SLEEP_OFF,          5,  0,
+        ILI9XXX_SET_PIX_FMT,            0,  1, 0x55,
+        ILI9XXX_SET_GAMMA,              0,  1, 0x04,
+        ILI9XXX_ENABLE_3_GAMMA,         0,  1, 0x01,
+        ILI9XXX_SET_FUNCTION_CTL,       0,  2, 0xFF, 0x06,
+        ILI9XXX_SET_PGAMMA,             0, 15, 0x36, 0x29, 0x12, 0x22, 0x1C, 0x15, 0x42, 0xB7, 0x2F, 0x13, 0x12, 0x0A, 0x11, 0x0B, 0x06,
+        ILI9XXX_SET_NGAMMA,             0, 15, 0x09, 0x16, 0x2D, 0x0D, 0x13, 0x15, 0x40, 0x48, 0x53, 0x0C, 0x1D, 0x25, 0x2E, 0x34, 0x39,
+        ILI9XXX_SET_FRAME_CTL_NORMAL,   0,  2, 0x08, 0x02,
+        ILI9XXX_SET_POWER_CTL_1,        0,  2, 0x0A, 0x02,
+        ILI9XXX_SET_POWER_CTL_2,        0,  1, 0x02,
+        ILI9XXX_SET_VCOM_CTL_1,         0,  2, 0x50, 0x63,
+        ILI9XXX_SET_VCOM_CTL_2,         0,  1, 0x00,
+        ILI9XXX_CMD_PARTIAL_OFF,        0,  0,
+        ILI9XXX_CMD_DISPLAY_ON,        20,  0
+    };
+    // clang-format on
+    qp_comms_bulk_command_sequence(device, ili9163_init_sequence, sizeof(ili9163_init_sequence));
+
+    // Configure the rotation (i.e. the ordering and direction of memory writes in GRAM)
+    const uint8_t madctl[] = {
+        [QP_ROTATION_0]   = ILI9XXX_MADCTL_BGR,
+        [QP_ROTATION_90]  = ILI9XXX_MADCTL_BGR | ILI9XXX_MADCTL_MX | ILI9XXX_MADCTL_MV,
+        [QP_ROTATION_180] = ILI9XXX_MADCTL_BGR | ILI9XXX_MADCTL_MX | ILI9XXX_MADCTL_MY,
+        [QP_ROTATION_270] = ILI9XXX_MADCTL_BGR | ILI9XXX_MADCTL_MV | ILI9XXX_MADCTL_MY,
+    };
+    qp_comms_command_databyte(device, ILI9XXX_SET_MEM_ACS_CTL, madctl[rotation]);
+
+    return true;
+}
+
+////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
+// Driver vtable
+
+const struct tft_panel_dc_reset_painter_driver_vtable_t ili9163_driver_vtable = {
+    .base =
+        {
+            .init            = qp_ili9163_init,
+            .power           = qp_tft_panel_power,
+            .clear           = qp_tft_panel_clear,
+            .flush           = qp_tft_panel_flush,
+            .pixdata         = qp_tft_panel_pixdata,
+            .viewport        = qp_tft_panel_viewport,
+            .palette_convert = qp_tft_panel_palette_convert,
+            .append_pixels   = qp_tft_panel_append_pixels,
+        },
+    .rgb888_to_native16bit = qp_rgb888_to_rgb565_swapped,
+    .num_window_bytes      = 2,
+    .swap_window_coords    = false,
+    .opcodes =
+        {
+            .display_on         = ILI9XXX_CMD_DISPLAY_ON,
+            .display_off        = ILI9XXX_CMD_DISPLAY_OFF,
+            .set_column_address = ILI9XXX_SET_COL_ADDR,
+            .set_row_address    = ILI9XXX_SET_PAGE_ADDR,
+            .enable_writes      = ILI9XXX_SET_MEM,
+        },
+};
+
+////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
+// SPI
+
+#ifdef QUANTUM_PAINTER_ILI9163_SPI_ENABLE
+
+// Factory function for creating a handle to the ILI9163 device
+painter_device_t qp_ili9163_make_spi_device(uint16_t panel_width, uint16_t panel_height, pin_t chip_select_pin, pin_t dc_pin, pin_t reset_pin, uint16_t spi_divisor, int spi_mode) {
+    for (uint32_t i = 0; i < ILI9163_NUM_DEVICES; ++i) {
+        tft_panel_dc_reset_painter_device_t *driver = &ili9163_drivers[i];
+        if (!driver->base.driver_vtable) {
+            driver->base.driver_vtable         = (const struct painter_driver_vtable_t *)&ili9163_driver_vtable;
+            driver->base.comms_vtable          = (const struct painter_comms_vtable_t *)&spi_comms_with_dc_vtable;
+            driver->base.panel_width           = panel_width;
+            driver->base.panel_height          = panel_height;
+            driver->base.rotation              = QP_ROTATION_0;
+            driver->base.offset_x              = 0;
+            driver->base.offset_y              = 0;
+            driver->base.native_bits_per_pixel = 16; // RGB565
+
+            // SPI and other pin configuration
+            driver->base.comms_config                              = &driver->spi_dc_reset_config;
+            driver->spi_dc_reset_config.spi_config.chip_select_pin = chip_select_pin;
+            driver->spi_dc_reset_config.spi_config.divisor         = spi_divisor;
+            driver->spi_dc_reset_config.spi_config.lsb_first       = false;
+            driver->spi_dc_reset_config.spi_config.mode            = spi_mode;
+            driver->spi_dc_reset_config.dc_pin                     = dc_pin;
+            driver->spi_dc_reset_config.reset_pin                  = reset_pin;
+            return (painter_device_t)driver;
+        }
+    }
+    return NULL;
+}
+
+#endif // QUANTUM_PAINTER_ILI9163_SPI_ENABLE
+
+////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
diff --git a/drivers/painter/ili9xxx/qp_ili9163.h b/drivers/painter/ili9xxx/qp_ili9163.h
new file mode 100644
index 0000000000..88d23629a9
--- /dev/null
+++ b/drivers/painter/ili9xxx/qp_ili9163.h
@@ -0,0 +1,37 @@
+// Copyright 2021 Nick Brassel (@tzarc)
+// SPDX-License-Identifier: GPL-2.0-or-later
+
+#pragma once
+
+#include "gpio.h"
+#include "qp_internal.h"
+
+////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
+// Quantum Painter ILI9163 configurables (add to your keyboard's config.h)
+
+#ifndef ILI9163_NUM_DEVICES
+/**
+ * @def This controls the maximum number of ILI9163 devices that Quantum Painter can communicate with at any one time.
+ *      Increasing this number allows for multiple displays to be used.
+ */
+#    define ILI9163_NUM_DEVICES 1
+#endif
+
+////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
+// Quantum Painter ILI9163 device factories
+
+#ifdef QUANTUM_PAINTER_ILI9163_SPI_ENABLE
+/**
+ * Factory method for an ILI9163 SPI LCD device.
+ *
+ * @param panel_width[in] the width of the display panel
+ * @param panel_height[in] the height of the display panel
+ * @param chip_select_pin[in] the GPIO pin used for SPI chip select
+ * @param dc_pin[in] the GPIO pin used for D/C control
+ * @param reset_pin[in] the GPIO pin used for RST
+ * @param spi_divisor[in] the SPI divisor to use when communicating with the display
+ * @param spi_mode[in] the SPI mode to use when communicating with the display
+ * @return the device handle used with all drawing routines in Quantum Painter
+ */
+painter_device_t qp_ili9163_make_spi_device(uint16_t panel_width, uint16_t panel_height, pin_t chip_select_pin, pin_t dc_pin, pin_t reset_pin, uint16_t spi_divisor, int spi_mode);
+#endif // QUANTUM_PAINTER_ILI9163_SPI_ENABLE
diff --git a/drivers/painter/ili9xxx/qp_ili9341.c b/drivers/painter/ili9xxx/qp_ili9341.c
new file mode 100644
index 0000000000..1f41dcfc0b
--- /dev/null
+++ b/drivers/painter/ili9xxx/qp_ili9341.c
@@ -0,0 +1,128 @@
+// Copyright 2021 Nick Brassel (@tzarc)
+// SPDX-License-Identifier: GPL-2.0-or-later
+
+#include "qp_internal.h"
+#include "qp_comms.h"
+#include "qp_ili9341.h"
+#include "qp_ili9xxx_opcodes.h"
+#include "qp_tft_panel.h"
+
+#ifdef QUANTUM_PAINTER_ILI9341_SPI_ENABLE
+#    include <qp_comms_spi.h>
+#endif // QUANTUM_PAINTER_ILI9341_SPI_ENABLE
+
+////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
+// Common
+
+// Driver storage
+tft_panel_dc_reset_painter_device_t ili9341_drivers[ILI9341_NUM_DEVICES] = {0};
+
+////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
+// Initialization
+
+bool qp_ili9341_init(painter_device_t device, painter_rotation_t rotation) {
+    // clang-format off
+    const uint8_t ili9341_init_sequence[] = {
+        // Command,                 Delay,  N, Data[N]
+        ILI9XXX_CMD_RESET,            120,  0,
+        ILI9XXX_CMD_SLEEP_OFF,          5,  0,
+        ILI9XXX_POWER_CTL_A,            0,  5, 0x39, 0x2C, 0x00, 0x34, 0x02,
+        ILI9XXX_POWER_CTL_B,            0,  3, 0x00, 0xD9, 0x30,
+        ILI9XXX_POWER_ON_SEQ_CTL,       0,  4, 0x64, 0x03, 0x12, 0x81,
+        ILI9XXX_SET_PUMP_RATIO_CTL,     0,  1, 0x20,
+        ILI9XXX_SET_POWER_CTL_1,        0,  1, 0x26,
+        ILI9XXX_SET_POWER_CTL_2,        0,  1, 0x11,
+        ILI9XXX_SET_VCOM_CTL_1,         0,  2, 0x35, 0x3E,
+        ILI9XXX_SET_VCOM_CTL_2,         0,  1, 0xBE,
+        ILI9XXX_DRV_TIMING_CTL_A,       0,  3, 0x85, 0x10, 0x7A,
+        ILI9XXX_DRV_TIMING_CTL_B,       0,  2, 0x00, 0x00,
+        ILI9XXX_SET_BRIGHTNESS,         0,  1, 0xFF,
+        ILI9XXX_ENABLE_3_GAMMA,         0,  1, 0x00,
+        ILI9XXX_SET_GAMMA,              0,  1, 0x01,
+        ILI9XXX_SET_PGAMMA,             0, 15, 0x0F, 0x29, 0x24, 0x0C, 0x0E, 0x09, 0x4E, 0x78, 0x3C, 0x09, 0x13, 0x05, 0x17, 0x11, 0x00,
+        ILI9XXX_SET_NGAMMA,             0, 15, 0x00, 0x16, 0x1B, 0x04, 0x11, 0x07, 0x31, 0x33, 0x42, 0x05, 0x0C, 0x0A, 0x28, 0x2F, 0x0F,
+        ILI9XXX_SET_PIX_FMT,            0,  1, 0x05,
+        ILI9XXX_SET_FRAME_CTL_NORMAL,   0,  2, 0x00, 0x1B,
+        ILI9XXX_SET_FUNCTION_CTL,       0,  2, 0x0A, 0xA2,
+        ILI9XXX_CMD_PARTIAL_OFF,        0,  0,
+        ILI9XXX_CMD_DISPLAY_ON,        20,  0
+    };
+    // clang-format on
+    qp_comms_bulk_command_sequence(device, ili9341_init_sequence, sizeof(ili9341_init_sequence));
+
+    // Configure the rotation (i.e. the ordering and direction of memory writes in GRAM)
+    const uint8_t madctl[] = {
+        [QP_ROTATION_0]   = ILI9XXX_MADCTL_BGR,
+        [QP_ROTATION_90]  = ILI9XXX_MADCTL_BGR | ILI9XXX_MADCTL_MX | ILI9XXX_MADCTL_MV,
+        [QP_ROTATION_180] = ILI9XXX_MADCTL_BGR | ILI9XXX_MADCTL_MX | ILI9XXX_MADCTL_MY,
+        [QP_ROTATION_270] = ILI9XXX_MADCTL_BGR | ILI9XXX_MADCTL_MV | ILI9XXX_MADCTL_MY,
+    };
+    qp_comms_command_databyte(device, ILI9XXX_SET_MEM_ACS_CTL, madctl[rotation]);
+
+    return true;
+}
+
+////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
+// Driver vtable
+
+const struct tft_panel_dc_reset_painter_driver_vtable_t ili9341_driver_vtable = {
+    .base =
+        {
+            .init            = qp_ili9341_init,
+            .power           = qp_tft_panel_power,
+            .clear           = qp_tft_panel_clear,
+            .flush           = qp_tft_panel_flush,
+            .pixdata         = qp_tft_panel_pixdata,
+            .viewport        = qp_tft_panel_viewport,
+            .palette_convert = qp_tft_panel_palette_convert,
+