diff options
Diffstat (limited to 'drivers/chibios/ws2812.c')
| -rw-r--r-- | drivers/chibios/ws2812.c | 114 |
1 files changed, 0 insertions, 114 deletions
diff --git a/drivers/chibios/ws2812.c b/drivers/chibios/ws2812.c deleted file mode 100644 index 0d12e2fb79..0000000000 --- a/drivers/chibios/ws2812.c +++ /dev/null @@ -1,114 +0,0 @@ -#include "quantum.h" -#include "ws2812.h" -#include <ch.h> -#include <hal.h> - -/* Adapted from https://github.com/bigjosh/SimpleNeoPixelDemo/ */ - -#ifndef NOP_FUDGE -# if defined(STM32F0XX) || defined(STM32F1XX) || defined(STM32F3XX) || defined(STM32F4XX) || defined(STM32L0XX) -# define NOP_FUDGE 0.4 -# else -# error("NOP_FUDGE configuration required") -# define NOP_FUDGE 1 // this just pleases the compile so the above error is easier to spot -# endif -#endif - -// Push Pull or Open Drain Configuration -// Default Push Pull -#ifndef WS2812_EXTERNAL_PULLUP -# define WS2812_OUTPUT_MODE PAL_MODE_OUTPUT_PUSHPULL -#else -# define WS2812_OUTPUT_MODE PAL_MODE_OUTPUT_OPENDRAIN -#endif - -#define NUMBER_NOPS 6 -#define CYCLES_PER_SEC (STM32_SYSCLK / NUMBER_NOPS * NOP_FUDGE) -#define NS_PER_SEC (1000000000L) // Note that this has to be SIGNED since we want to be able to check for negative values of derivatives -#define NS_PER_CYCLE (NS_PER_SEC / CYCLES_PER_SEC) -#define NS_TO_CYCLES(n) ((n) / NS_PER_CYCLE) - -#define wait_ns(x) \ - do { \ - for (int i = 0; i < NS_TO_CYCLES(x); i++) { \ - __asm__ volatile("nop\n\t" \ - "nop\n\t" \ - "nop\n\t" \ - "nop\n\t" \ - "nop\n\t" \ - "nop\n\t"); \ - } \ - } while (0) - -// These are the timing constraints taken mostly from the WS2812 datasheets -// These are chosen to be conservative and avoid problems rather than for maximum throughput - -#define T1H 900 // Width of a 1 bit in ns -#define T1L (1250 - T1H) // Width of a 1 bit in ns - -#define T0H 350 // Width of a 0 bit in ns -#define T0L (1250 - T0H) // Width of a 0 bit in ns - -// The reset gap can be 6000 ns, but depending on the LED strip it may have to be increased -// to values like 600000 ns. If it is too small, the pixels will show nothing most of the time. -#define RES (1000 * WS2812_TRST_US) // Width of the low gap between bits to cause a frame to latch - -void sendByte(uint8_t byte) { - // WS2812 protocol wants most significant bits first - for (unsigned char bit = 0; bit < 8; bit++) { - bool is_one = byte & (1 << (7 - bit)); - // using something like wait_ns(is_one ? T1L : T0L) here throws off timings - if (is_one) { - // 1 - writePinHigh(RGB_DI_PIN); - wait_ns(T1H); - writePinLow(RGB_DI_PIN); - wait_ns(T1L); - } else { - // 0 - writePinHigh(RGB_DI_PIN); - wait_ns(T0H); - writePinLow(RGB_DI_PIN); - wait_ns(T0L); - } - } -} - -void ws2812_init(void) { palSetLineMode(RGB_DI_PIN, WS2812_OUTPUT_MODE); } - -// Setleds for standard RGB -void ws2812_setleds(LED_TYPE *ledarray, uint16_t leds) { - static bool s_init = false; - if (!s_init) { - ws2812_init(); - s_init = true; - } - - // this code is very time dependent, so we need to disable interrupts - chSysLock(); - - for (uint8_t i = 0; i < leds; i++) { - // WS2812 protocol dictates grb order -#if (WS2812_BYTE_ORDER == WS2812_BYTE_ORDER_GRB) - sendByte(ledarray[i].g); - sendByte(ledarray[i].r); - sendByte(ledarray[i].b); -#elif (WS2812_BYTE_ORDER == WS2812_BYTE_ORDER_RGB) - sendByte(ledarray[i].r); - sendByte(ledarray[i].g); - sendByte(ledarray[i].b); -#elif (WS2812_BYTE_ORDER == WS2812_BYTE_ORDER_BGR) - sendByte(ledarray[i].b); - sendByte(ledarray[i].g); - sendByte(ledarray[i].r); -#endif - -#ifdef RGBW - sendByte(ledarray[i].w); -#endif - } - - wait_ns(RES); - - chSysUnlock(); -} |