diff options
Diffstat (limited to 'docs')
| -rw-r--r-- | docs/faq_build.md | 123 |
1 files changed, 43 insertions, 80 deletions
diff --git a/docs/faq_build.md b/docs/faq_build.md index e2d0f9b27a..990ebe3aff 100644 --- a/docs/faq_build.md +++ b/docs/faq_build.md @@ -13,63 +13,66 @@ An example of using `sudo`, when your controller is ATMega32u4: or just: - $ sudo make <keyboard>:<keymap>:dfu + $ sudo make <keyboard>:<keymap>:flash Note that running `make` with `sudo` is generally ***not*** a good idea, and you should use one of the former methods, if possible. ### Linux `udev` Rules -On Linux, you'll need proper privileges to access the MCU. You can either use -`sudo` when flashing firmware, or place these files in `/etc/udev/rules.d/`. Once added run the following: -```console -sudo udevadm control --reload-rules -sudo udevadm trigger -``` -**/etc/udev/rules.d/50-atmel-dfu.rules:** -``` -# Atmel ATMega32U4 -SUBSYSTEMS=="usb", ATTRS{idVendor}=="03eb", ATTRS{idProduct}=="2ff4", TAG+="uaccess", RUN{builtin}+="uaccess" -# Atmel USBKEY AT90USB1287 -SUBSYSTEMS=="usb", ATTRS{idVendor}=="03eb", ATTRS{idProduct}=="2ffb", TAG+="uaccess", RUN{builtin}+="uaccess" -# Atmel ATMega32U2 -SUBSYSTEMS=="usb", ATTRS{idVendor}=="03eb", ATTRS{idProduct}=="2ff0", TAG+="uaccess", RUN{builtin}+="uaccess" +On Linux, you'll need proper privileges to communicate with the bootloader device. You can either use `sudo` when flashing firmware, or place this file in `/etc/udev/rules.d/`: + +**/etc/udev/rules.d/50-qmk.rules:** ``` +# Atmel DFU +# ATmega16U2 +SUBSYSTEMS=="usb", ATTRS{idVendor}=="03EB", ATTRS{idProduct}=="2FEF", TAG+="uaccess", RUN{builtin}+="uaccess" +# ATmega32U2 +SUBSYSTEMS=="usb", ATTRS{idVendor}=="03EB", ATTRS{idProduct}=="2FF0", TAG+="uaccess", RUN{builtin}+="uaccess" +# ATmega16U4 +SUBSYSTEMS=="usb", ATTRS{idVendor}=="03EB", ATTRS{idProduct}=="2FF3", TAG+="uaccess", RUN{builtin}+="uaccess" +# ATmega32U4 +SUBSYSTEMS=="usb", ATTRS{idVendor}=="03EB", ATTRS{idProduct}=="2FF4", TAG+="uaccess", RUN{builtin}+="uaccess" +# AT90USB128 +SUBSYSTEMS=="usb", ATTRS{idVendor}=="03EB", ATTRS{idProduct}=="2FF9", TAG+="uaccess", RUN{builtin}+="uaccess" +# AT90USB128 +SUBSYSTEMS=="usb", ATTRS{idVendor}=="03EB", ATTRS{idProduct}=="2FFB", TAG+="uaccess", RUN{builtin}+="uaccess" -**/etc/udev/rules.d/54-input-club-keyboard.rules:** +# Input Club +SUBSYSTEMS=="usb", ATTRS{idVendor}=="1C11", ATTRS{idProduct}=="B007", TAG+="uaccess", RUN{builtin}+="uaccess" -``` -# Input Club keyboard bootloader -SUBSYSTEMS=="usb", ATTRS{idVendor}=="1c11", ATTRS{idProduct}=="b007", TAG+="uaccess", RUN{builtin}+="uaccess" -``` +# STM32duino +SUBSYSTEMS=="usb", ATTRS{idVendor}=="1EAF", ATTRS{idProduct}=="0003", TAG+="uaccess", RUN{builtin}+="uaccess" +# STM32 DFU +SUBSYSTEMS=="usb", ATTRS{idVendor}=="0483", ATTRS{idProduct}=="DF11", TAG+="uaccess", RUN{builtin}+="uaccess" + +# BootloadHID +SUBSYSTEMS=="usb", ATTRS{idVendor}=="16C0", ATTRS{idProduct}=="05DF", TAG+="uaccess", RUN{builtin}+="uaccess" + +# USBAspLoader +SUBSYSTEMS=="usb", ATTRS{idVendor}=="16C0", ATTRS{idProduct}=="05DC", TAG+="uaccess", RUN{builtin}+="uaccess" -**/etc/udev/rules.d/55-caterina.rules:** -``` # ModemManager should ignore the following devices -SUBSYSTEMS=="usb", ATTRS{idVendor}=="2a03", ATTRS{idProduct}=="0036", TAG+="uaccess", RUN{builtin}+="uaccess", ENV{ID_MM_DEVICE_IGNORE}="1" -SUBSYSTEMS=="usb", ATTRS{idVendor}=="2341", ATTRS{idProduct}=="0036", TAG+="uaccess", RUN{builtin}+="uaccess", ENV{ID_MM_DEVICE_IGNORE}="1" -SUBSYSTEMS=="usb", ATTRS{idVendor}=="1b4f", ATTRS{idProduct}=="9205", TAG+="uaccess", RUN{builtin}+="uaccess", ENV{ID_MM_DEVICE_IGNORE}="1" -SUBSYSTEMS=="usb", ATTRS{idVendor}=="1b4f", ATTRS{idProduct}=="9203", TAG+="uaccess", RUN{builtin}+="uaccess", ENV{ID_MM_DEVICE_IGNORE}="1" +# Atmel SAM-BA (Massdrop) +SUBSYSTEMS=="usb", ATTRS{idVendor}=="03EB" ATTRS{idProduct}=="6124" TAG+="uaccess", RUN{builtin}+="uaccess", ENV{ID_MM_DEVICE_IGNORE}="1" +# Caterina +SUBSYSTEMS=="usb", ATTRS{idVendor}=="2A03" TAG+="uaccess", RUN{builtin}+="uaccess", ENV{ID_MM_DEVICE_IGNORE}="1" +SUBSYSTEMS=="usb", ATTRS{idVendor}=="2341" TAG+="uaccess", RUN{builtin}+="uaccess", ENV{ID_MM_DEVICE_IGNORE}="1" +SUBSYSTEMS=="usb", ATTRS{idVendor}=="1B4F" TAG+="uaccess", RUN{builtin}+="uaccess", ENV{ID_MM_DEVICE_IGNORE}="1" ``` -**Note:** With older (before 1.12) ModemManager, filtering only works when not in strict mode, the following commands can update that settings: -```console -printf '[Service]\nExecStart=\nExecStart=/usr/sbin/ModemManager --filter-policy=default' | sudo tee /etc/systemd/system/ModemManager.service.d/policy.conf -sudo systemctl daemon-reload -sudo systemctl restart ModemManager -``` +Once added, run the following: -**/etc/udev/rules.d/56-dfu-util.rules:** ``` -# stm32duino -SUBSYSTEMS=="usb", ATTRS{idVendor}=="1eaf", ATTRS{idProduct}=="0003", TAG+="uaccess", RUN{builtin}+="uaccess" -# Generic stm32 -SUBSYSTEMS=="usb", ATTRS{idVendor}=="0483", ATTRS{idProduct}=="df11", TAG+="uaccess", RUN{builtin}+="uaccess" +sudo udevadm control --reload-rules +sudo udevadm trigger ``` -**/etc/udev/rules.d/57-bootloadhid.rules:** +**Note:** With older versions of ModemManager (< 1.12), filtering only works when not in strict mode. The following commands can update that setting: + ``` -# bootloadHID -SUBSYSTEMS=="usb", ATTRS{idVendor}=="16c0", ATTRS{idProduct}=="05df", TAG+="uaccess", RUN{builtin}+="uaccess" +printf '[Service]\nExecStart=\nExecStart=/usr/sbin/ModemManager --filter-policy=default' | sudo tee /etc/systemd/system/ModemManager.service.d/policy.conf +sudo systemctl daemon-reload +sudo systemctl restart ModemManager ``` ### Serial device is not detected in bootloader mode on Linux @@ -96,46 +99,6 @@ You can buy a really unique VID:PID here. I don't think you need this for person - http://www.obdev.at/products/vusb/license.html - http://www.mcselec.com/index.php?page=shop.product_details&flypage=shop.flypage&product_id=92&option=com_phpshop&Itemid=1 -## BOOTLOADER_SIZE for AVR -Note that Teensy2.0++ bootloader size is 2048byte. Some Makefiles may have wrong comment. - -``` -# Boot Section Size in *bytes* -# Teensy halfKay 512 -# Teensy++ halfKay 2048 -# Atmel DFU loader 4096 (TMK Alt Controller) -# LUFA bootloader 4096 -# USBaspLoader 2048 -OPT_DEFS += -DBOOTLOADER_SIZE=2048 -``` - -## `avr-gcc: internal compiler error: Abort trap: 6 (program cc1)` on MacOS - -This is an issue with updating on brew, causing symlinks that avr-gcc depend on getting mangled. - -The solution is to remove and reinstall all affected modules. - -``` -brew rm avr-gcc avr-gcc@8 dfu-programmer dfu-util gcc-arm-none-eabi arm-gcc-bin@8 avrdude qmk -brew install qmk/qmk/qmk -brew link --force avr-gcc@8 -brew link --force arm-gcc-bin@8 -``` - -### `avr-gcc` and LUFA - -If you updated your `avr-gcc` and you see errors involving LUFA, for example: - -`lib/lufa/LUFA/Drivers/USB/Class/Device/AudioClassDevice.h:380:5: error: 'const' attribute on function returning 'void'` - -For now, you need to rollback `avr-gcc` to 8 in Homebrew. - -``` -brew uninstall --force avr-gcc -brew install avr-gcc@8 -brew link --force avr-gcc@8 -``` - ### I just flashed my keyboard and it does nothing/keypresses don't register - it's also ARM (rev6 planck, clueboard 60, hs60v2, etc...) (Feb 2019) Due to how EEPROM works on ARM based chips, saved settings may no longer be valid. This affects the default layers, and *may*, under certain circumstances we are still figuring out, make the keyboard unusable. Resetting the EEPROM will correct this. |