diff options
Diffstat (limited to 'docs')
| -rw-r--r-- | docs/feature_rgb_matrix.md | 2 | ||||
| -rw-r--r-- | docs/keycodes.md | 3 | ||||
| -rw-r--r-- | docs/one_shot_keys.md | 3 | ||||
| -rw-r--r-- | docs/ws2812_driver.md | 22 |
4 files changed, 30 insertions, 0 deletions
diff --git a/docs/feature_rgb_matrix.md b/docs/feature_rgb_matrix.md index e996cadddd..046b1f17fa 100644 --- a/docs/feature_rgb_matrix.md +++ b/docs/feature_rgb_matrix.md @@ -447,6 +447,8 @@ These are defined in [`rgblight_list.h`](https://github.com/qmk/qmk_firmware/blo #define RGB_MATRIX_STARTUP_VAL RGB_MATRIX_MAXIMUM_BRIGHTNESS // Sets the default brightness value, if none has been set #define RGB_MATRIX_STARTUP_SPD 127 // Sets the default animation speed, if none has been set #define RGB_MATRIX_DISABLE_KEYCODES // disables control of rgb matrix by keycodes (must use code functions to control the feature) +#define RGB_MATRIX_SPLIT { X, Y } // (Optional) For split keyboards, the number of LEDs connected on each half. X = left, Y = Right. + // If RGB_MATRIX_KEYPRESSES or RGB_MATRIX_KEYRELEASES is enabled, you also will want to enable SPLIT_TRANSPORT_MIRROR ``` ## EEPROM storage :id=eeprom-storage diff --git a/docs/keycodes.md b/docs/keycodes.md index 9acf8b6839..f3c519b130 100644 --- a/docs/keycodes.md +++ b/docs/keycodes.md @@ -516,6 +516,9 @@ See also: [One Shot Keys](one_shot_keys.md) |------------|----------------------------------| |`OSM(mod)` |Hold `mod` for one keypress | |`OSL(layer)`|Switch to `layer` for one keypress| +|`OS_ON` |Turns One Shot keys on | +|`OS_OFF` |Turns One Shot keys off | +|`OS_TOGG` |Toggles One Shot keys status | ## Space Cadet :id=space-cadet diff --git a/docs/one_shot_keys.md b/docs/one_shot_keys.md index 9a082d7d6d..9fc5486299 100644 --- a/docs/one_shot_keys.md +++ b/docs/one_shot_keys.md @@ -17,6 +17,9 @@ You can control the behavior of one shot keys by defining these in `config.h`: * `OSM(mod)` - Momentarily hold down *mod*. You must use the `MOD_*` keycodes as shown in [Mod Tap](mod_tap.md), not the `KC_*` codes. * `OSL(layer)` - momentary switch to *layer*. +* `OS_ON` - Turns on One Shot keys. +* `OS_OFF` - Turns off One Shot keys. OSM act as regular mod keys, OSL act like `MO`. +* `ON_TOGG` - Toggles the one shot key status. Sometimes, you want to activate a one-shot key as part of a macro or tap dance routine. diff --git a/docs/ws2812_driver.md b/docs/ws2812_driver.md index cca6827ec8..e69400364c 100644 --- a/docs/ws2812_driver.md +++ b/docs/ws2812_driver.md @@ -77,6 +77,25 @@ Configure the hardware via your config.h: You must also turn on the SPI feature in your halconf.h and mcuconf.h +#### Circular Buffer Mode +Some boards may flicker while in the normal buffer mode. To fix this issue, circular buffer mode may be used to rectify the issue. + +By default, the circular buffer mode is disabled. + +To enable this alternative buffer mode, place this into your `config.h` file: +```c +#define WS2812_SPI_USE_CIRCULAR_BUFFER +``` + +#### Setting baudrate with divisor +To adjust the baudrate at which the SPI peripheral is configured, users will need to derive the target baudrate from the clock tree provided by STM32CubeMX. + +Only divisors of 2, 4, 8, 16, 32, 64, 128 and 256 are supported by hardware. + +|Define |Default|Description | +|--------------------|-------|-------------------------------------| +|`WS2812_SPI_DIVISOR`|`16` |SPI source clock peripheral divisor | + #### Testing Notes While not an exhaustive list, the following table provides the scenarios that have been partially validated: @@ -102,11 +121,14 @@ Configure the hardware via your config.h: #define WS2812_PWM_DRIVER PWMD2 // default: PWMD2 #define WS2812_PWM_CHANNEL 2 // default: 2 #define WS2812_PWM_PAL_MODE 2 // Pin "alternate function", see the respective datasheet for the appropriate values for your MCU. default: 2 +//#define WS2812_PWM_COMPLEMENTARY_OUTPUT // Define for a complementary timer output (TIMx_CHyN); omit for a normal timer output (TIMx_CHy). #define WS2812_DMA_STREAM STM32_DMA1_STREAM2 // DMA Stream for TIMx_UP, see the respective reference manual for the appropriate values for your MCU. #define WS2812_DMA_CHANNEL 2 // DMA Channel for TIMx_UP, see the respective reference manual for the appropriate values for your MCU. #define WS2812_DMAMUX_ID STM32_DMAMUX1_TIM2_UP // DMAMUX configuration for TIMx_UP -- only required if your MCU has a DMAMUX peripheral, see the respective reference manual for the appropriate values for your MCU. ``` +Note that using a complementary timer output (TIMx_CHyN) is possible only for advanced-control timers (TIM1, TIM8, TIM20 on STM32), and the `STM32_PWM_USE_ADVANCED` option in mcuconf.h must be set to `TRUE`. Complementary outputs of general-purpose timers are not supported due to ChibiOS limitations. + You must also turn on the PWM feature in your halconf.h and mcuconf.h #### Testing Notes |