1 files changed, 0 insertions, 91 deletions
diff --git a/docs/proton_c_conversion.md b/docs/proton_c_conversion.md
deleted file mode 100644
index 1e1b1e806d..0000000000
--- a/docs/proton_c_conversion.md
+++ /dev/null
@@ -1,91 +0,0 @@
-# Converting a board to use the Proton C
-
-Since the Proton C is a drop-in replacement for a Pro Micro we've made it easy to use. This page documents a handy automated process for converting keyboards, as well as documenting the manual process if you'd like to make use of Proton C features that aren't available on Pro Micros.
-
-## Automatic Conversion
-
-If a board currently supported in QMK uses a Pro Micro (or compatible board) and you want to use the Proton C, you can generate the firmware by appending `CONVERT_TO_PROTON_C=yes` (or `CTPC=yes`) to your make argument, like this:
-
-    make 40percentclub/mf68:default CTPC=yes
-
-You can add the same argument to your keymap's `rules.mk`, which will accomplish the same thing.
-
-This exposes the `CONVERT_TO_PROTON_C` flag that you can use in your code with `#ifdef`s, like this:
-
-```c
-#ifdef CONVERT_TO_PROTON_C
-    // Proton C code
-#else
-    // Pro Micro code
-#endif
-```
-
-If you get errors about `PORTB/DDRB`, etc not being defined, so you'll need to convert the keyboard's code to use the [GPIO Controls](gpio_control.md) that will work for both ARM and AVR. This shouldn't affect the AVR builds at all.
-
-The Proton C only has one on-board LED (C13), and by default, the TXLED (D5) is mapped to it. If you want the RXLED (B0) mapped to it instead, add this like to your `config.h`:
-
-    #define CONVERT_TO_PROTON_C_RXLED
-
-## Feature Conversion
-
-These are defaults based on what has been implemented for ARM boards.
-
-| Feature                             | Notes                                                                                                            |
-|-------------------------------------|------------------------------------------------------------------------------------------------------------------|
-| [Audio](feature_audio.md)           | Enabled                                                                                                          |  
-| [RGB Lighting](feature_rgblight.md) | Disabled                                                                                                         |
-| [Backlight](feature_backlight.md)   | Forces [task driven PWM](feature_backlight.md#software-pwm-driver) until ARM can provide automatic configuration |
-| USB Host (e.g. USB-USB converter)   | Not supported (USB host code is AVR specific and is not currently supported on ARM)                              |
-| [Split keyboards](feature_split_keyboard.md) | Partial - heavily dependent on enabled features                                                         |
-
-## Manual Conversion
-
-To use the Proton C natively, without having to specify `CTPC=yes`, you need to change the `MCU` line in `rules.mk`:
-
-```
-MCU = STM32F303
-BOARD = QMK_PROTON_C
-```
-
-Remove these variables if they exist:
-
-* `BOOTLOADER`
-* `EXTRA_FLAGS`
-
-Finally convert all pin assignments in `config.h` to the stm32 equivalents.
-
-| Pro Micro Left | Proton C Left | | Proton C Right | Pro Micro Right |
-|-----------|----------|-|----------|-----------|
-| `D3` | `A9` | | 5v | RAW (5v) |
-| `D2` | `A10` | | GND | GND |
-| GND | GND | | FLASH | RESET |
-| GND | GND | | 3.3v | VCC <sup>1</sup> |
-| `D1` | `B7` | | `A2` | `F4` |
-| `D0` | `B6` | | `A1` | `F5` |
-| `D4` | `B5` | | `A0` | `F6` |
-| `C6` | `B4` | | `B8` | `F7` |
-| `D7` | `B3` | | `B13` | `B1` |
-| `E6` | `B2` | | `B14` | `B3` |
-| `B4` | `B1` | | `B15` | `B2` |
-| `B5` | `B0` | | `B9` | `B6` |
-| `B0` (RX LED) | `C13` <sup>2</sup> | | `C13` <sup>2</sup> | `D5` (TX LED) |
-
-You can also make use of several new pins on the extended portion of the Proton C:
-
-| Left | | Right | 
-|------|-|-------|
-| `A4`<sup>3</sup> | | `B10` |
-| `A5`<sup>4</sup> | | `B11` |
-| `A6` | | `B12` |
-| `A7` | | `A14`<sup>5</sup> (SWCLK) |
-| `A8` | | `A13`<sup>5</sup> (SWDIO) |
-| `A15` | | RESET<sup>6</sup> |
-
-Notes:
-
-1. On a Pro Micro VCC can be 3.3v or 5v.
-2. A Proton C only has one onboard LED, not two like a Pro Micro. The Pro Micro has an RX LED on `D5` and a TX LED on `B0`.
-3. `A4` is shared with the speaker.
-4. `A5` is shared with the speaker.
-5. `A13` and `A14` are used for hardware debugging (SWD). You can also use them for GPIO, but should use them last.
-6. Short RESET to 3.3v (pull high) to reboot the MCU. This does not enter bootloader mode like a Pro Micro, it only resets the MCU.