summaryrefslogtreecommitdiffstats
path: root/docs/feature_rgb_matrix.md
diff options
context:
space:
mode:
Diffstat (limited to 'docs/feature_rgb_matrix.md')
-rw-r--r--docs/feature_rgb_matrix.md73
1 files changed, 54 insertions, 19 deletions
diff --git a/docs/feature_rgb_matrix.md b/docs/feature_rgb_matrix.md
index 2dbd32fbdb..6370c637a2 100644
--- a/docs/feature_rgb_matrix.md
+++ b/docs/feature_rgb_matrix.md
@@ -10,7 +10,7 @@ If you want to use single color LED's you should use the [LED Matrix Subsystem](
There is basic support for addressable RGB matrix lighting with the I2C IS31FL3731 RGB controller. To enable it, add this to your `rules.mk`:
-```makefile
+```make
RGB_MATRIX_ENABLE = yes
RGB_MATRIX_DRIVER = IS31FL3731
```
@@ -21,6 +21,7 @@ You can use between 1 and 4 IS31FL3731 IC's. Do not specify `DRIVER_ADDR_<N>` de
|----------|-------------|---------|
| `ISSI_TIMEOUT` | (Optional) How long to wait for i2c messages, in milliseconds | 100 |
| `ISSI_PERSISTENCE` | (Optional) Retry failed messages this many times | 0 |
+| `ISSI_3731_DEGHOST` | (Optional) Set this define to enable de-ghosting by halving Vcc during blanking time | |
| `DRIVER_COUNT` | (Required) How many RGB driver IC's are present | |
| `DRIVER_LED_TOTAL` | (Required) How many RGB lights are present across all drivers | |
| `DRIVER_ADDR_1` | (Required) Address for the first RGB driver | |
@@ -49,6 +50,8 @@ Here is an example using 2 drivers.
!> Note the parentheses, this is so when `DRIVER_LED_TOTAL` is used in code and expanded, the values are added together before any additional math is applied to them. As an example, `rand() % (DRIVER_1_LED_TOTAL + DRIVER_2_LED_TOTAL)` will give very different results than `rand() % DRIVER_1_LED_TOTAL + DRIVER_2_LED_TOTAL`.
+For split keyboards using `RGB_MATRIX_SPLIT` with an LED driver, you can either have the same driver address or different driver addresses. If using different addresses, use `DRIVER_ADDR_1` for one and `DRIVER_ADDR_2` for the other one. Then, in `g_is31_leds`, fill out the correct driver index (0 or 1). If using one address, use `DRIVER_ADDR_1` for both, and use index 0 for `g_is31_leds`.
+
Define these arrays listing all the LEDs in your `<keyboard>.c`:
```c
@@ -71,7 +74,7 @@ Where `Cx_y` is the location of the LED in the matrix defined by [the datasheet]
There is basic support for addressable RGB matrix lighting with the I2C IS31FL3733 RGB controller. To enable it, add this to your `rules.mk`:
-```makefile
+```make
RGB_MATRIX_ENABLE = yes
RGB_MATRIX_DRIVER = IS31FL3733
```
@@ -82,6 +85,9 @@ You can use between 1 and 4 IS31FL3733 IC's. Do not specify `DRIVER_ADDR_<N>` de
|----------|-------------|---------|
| `ISSI_TIMEOUT` | (Optional) How long to wait for i2c messages, in milliseconds | 100 |
| `ISSI_PERSISTENCE` | (Optional) Retry failed messages this many times | 0 |
+| `ISSI_PWM_FREQUENCY` | (Optional) PWM Frequency Setting - IS31FL3733B only | 0 |
+| `ISSI_SWPULLUP` | (Optional) Set the value of the SWx lines on-chip de-ghosting resistors | PUR_0R (Disabled) |
+| `ISSI_CSPULLUP` | (Optional) Set the value of the CSx lines on-chip de-ghosting resistors | PUR_0R (Disabled) |
| `DRIVER_COUNT` | (Required) How many RGB driver IC's are present | |
| `DRIVER_LED_TOTAL` | (Required) How many RGB lights are present across all drivers | |
| `DRIVER_ADDR_1` | (Required) Address for the first RGB driver | |
@@ -93,6 +99,18 @@ You can use between 1 and 4 IS31FL3733 IC's. Do not specify `DRIVER_ADDR_<N>` de
| `DRIVER_SYNC_3` | (Optional) Sync configuration for the third RGB driver | 0 |
| `DRIVER_SYNC_4` | (Optional) Sync configuration for the fourth RGB driver | 0 |
+The IS31FL3733 IC's have on-chip resistors that can be enabled to allow for de-ghosting of the RGB matrix. By default these resistors are not enabled (`ISSI_SWPULLUP`/`ISSI_CSPULLUP` are given the value of`PUR_0R`), the values that can be set to enable de-ghosting are as follows:
+
+| `ISSI_SWPULLUP/ISSI_CSPULLUP` | Description |
+|----------------------|-------------|
+| `PUR_0R` | (default) Do not use the on-chip resistors/enable de-ghosting |
+| `PUR_05KR` | The 0.5k Ohm resistor used during blanking period (t_NOL) |
+| `PUR_3KR` | The 3k Ohm resistor used at all times |
+| `PUR_4KR` | The 4k Ohm resistor used at all times |
+| `PUR_8KR` | The 8k Ohm resistor used at all times |
+| `PUR_16KR` | The 16k Ohm resistor used at all times |
+| `PUR_32KR` | The 32k Ohm resistor used during blanking period (t_NOL) |
+
Here is an example using 2 drivers.
```c
@@ -141,7 +159,7 @@ Where `X_Y` is the location of the LED in the matrix defined by [the datasheet](
There is basic support for addressable RGB matrix lighting with the I2C IS31FL3737 RGB controller. To enable it, add this to your `rules.mk`:
-```makefile
+```make
RGB_MATRIX_ENABLE = yes
RGB_MATRIX_DRIVER = IS31FL3737
```
@@ -153,11 +171,25 @@ Configure the hardware via your `config.h`:
|----------|-------------|---------|
| `ISSI_TIMEOUT` | (Optional) How long to wait for i2c messages, in milliseconds | 100 |
| `ISSI_PERSISTENCE` | (Optional) Retry failed messages this many times | 0 |
+| `ISSI_SWPULLUP` | (Optional) Set the value of the SWx lines on-chip de-ghosting resistors | PUR_0R (Disabled) |
+| `ISSI_CSPULLUP` | (Optional) Set the value of the CSx lines on-chip de-ghosting resistors | PUR_0R (Disabled) |
| `DRIVER_COUNT` | (Required) How many RGB driver IC's are present | |
| `DRIVER_LED_TOTAL` | (Required) How many RGB lights are present across all drivers | |
| `DRIVER_ADDR_1` | (Required) Address for the first RGB driver | |
| `DRIVER_ADDR_2` | (Optional) Address for the second RGB driver | |
+The IS31FL3737 IC's have on-chip resistors that can be enabled to allow for de-ghosting of the RGB matrix. By default these resistors are not enabled (`ISSI_SWPULLUP`/`ISSI_CSPULLUP` are given the value of`PUR_0R`), the values that can be set to enable de-ghosting are as follows:
+
+| `ISSI_SWPULLUP/ISSI_CSPULLUP` | Description |
+|----------------------|-------------|
+| `PUR_0R` | (default) Do not use the on-chip resistors/enable de-ghosting |
+| `PUR_05KR` | The 0.5k Ohm resistor used during blanking period (t_NOL) |
+| `PUR_1KR` | The 1k Ohm resistor used during blanking period (t_NOL) |
+| `PUR_2KR` | The 2k Ohm resistor used during blanking period (t_NOL) |
+| `PUR_4KR` | The 4k Ohm resistor used during blanking period (t_NOL) |
+| `PUR_8KR` | The 8k Ohm resistor during blanking period (t_NOL) |
+| `PUR_16KR` | The 16k Ohm resistor during blanking period (t_NOL) |
+| `PUR_32KR` | The 32k Ohm resistor used during blanking period (t_NOL) |
Here is an example using 2 drivers.
@@ -181,7 +213,7 @@ Here is an example using 2 drivers.
```
!> Note the parentheses, this is so when `DRIVER_LED_TOTAL` is used in code and expanded, the values are added together before any additional math is applied to them. As an example, `rand() % (DRIVER_1_LED_TOTAL + DRIVER_2_LED_TOTAL)` will give very different results than `rand() % DRIVER_1_LED_TOTAL + DRIVER_2_LED_TOTAL`.
-Currently only 2 drivers are supported, but it would be trivial to support all 4 combinations.
+Currently only 2 drivers are supported, but it would be trivial to support all 4 combinations.
Define these arrays listing all the LEDs in your `<keyboard>.c`:
@@ -206,7 +238,7 @@ Where `X_Y` is the location of the LED in the matrix defined by [the datasheet](
There is basic support for addressable RGB matrix lighting with a WS2811/WS2812{a,b,c} addressable LED strand. To enable it, add this to your `rules.mk`:
-```makefile
+```make
RGB_MATRIX_ENABLE = yes
RGB_MATRIX_DRIVER = WS2812
```
@@ -226,7 +258,7 @@ Configure the hardware via your `config.h`:
There is basic support for APA102 based addressable LED strands. To enable it, add this to your `rules.mk`:
-```makefile
+```make
RGB_MATRIX_ENABLE = yes
RGB_MATRIX_DRIVER = APA102
```
@@ -246,7 +278,7 @@ Configure the hardware via your `config.h`:
### AW20216 :id=aw20216
There is basic support for addressable RGB matrix lighting with the SPI AW20216 RGB controller. To enable it, add this to your `rules.mk`:
-```makefile
+```make
RGB_MATRIX_ENABLE = yes
RGB_MATRIX_DRIVER = AW20216
```
@@ -340,7 +372,7 @@ x = 224 / (NUMBER_OF_COLS - 1) * COL_POSITION
y = 64 / (NUMBER_OF_ROWS - 1) * ROW_POSITION
```
-Where NUMBER_OF_COLS, NUMBER_OF_ROWS, COL_POSITION, & ROW_POSITION are all based on the physical layout of your keyboard, not the electrical layout.
+Where NUMBER_OF_COLS, NUMBER_OF_ROWS, COL_POSITION, & ROW_POSITION are all based on the physical layout of your keyboard, not the electrical layout.
As mentioned earlier, the center of the keyboard by default is expected to be `{ 112, 32 }`, but this can be changed if you want to more accurately calculate the LED's physical `{ x, y }` positions. Keyboard designers can implement `#define RGB_MATRIX_CENTER { 112, 32 }` in their config.h file with the new center point of the keyboard, or where they want it to be allowing more possibilities for the `{ x, y }` values. Do note that the maximum value for x or y is 255, and the recommended maximum is 224 as this gives animations runoff room before they reset.
@@ -383,7 +415,7 @@ All RGB keycodes are currently shared with the RGBLIGHT system:
* `RGB_MODE_*` keycodes will generally work, but not all of the modes are currently mapped to the correct effects for the RGB Matrix system.
-`RGB_MODE_PLAIN`, `RGB_MODE_BREATHE`, `RGB_MODE_RAINBOW`, and `RGB_MATRIX_SWIRL` are the only ones that are mapped properly. The rest don't have a direct equivalent, and are not mapped.
+`RGB_MODE_PLAIN`, `RGB_MODE_BREATHE`, `RGB_MODE_RAINBOW`, and `RGB_MATRIX_SWIRL` are the only ones that are mapped properly. The rest don't have a direct equivalent, and are not mapped.
!> By default, if you have both the [RGB Light](feature_rgblight.md) and the RGB Matrix feature enabled, these keycodes will work for both features, at the same time. You can disable the keycode functionality by defining the `*_DISABLE_KEYCODES` option for the specific feature.
@@ -420,7 +452,9 @@ enum rgb_matrix_effects {
RGB_MATRIX_JELLYBEAN_RAINDROPS, // Randomly changes a single key's hue and saturation
RGB_MATRIX_HUE_BREATHING, // Hue shifts up a slight ammount at the same time, then shifts back
RGB_MATRIX_HUE_PENDULUM, // Hue shifts up a slight ammount in a wave to the right, then back to the left
- RGB_MATRIX_HUE_WAVE, // Hue shifts up a slight ammount and then back down in a wave to the right
+ RGB_MATRIX_HUE_WAVE, // Hue shifts up a slight ammount and then back down in a wave to the right
+ RGB_MATRIX_FRACTAL, // Single hue fractal filled keys pulsing horizontally out to edges
+ RGB_MATRIX_PIXEL_RAIN, // Randomly light keys with random hues
#if define(RGB_MATRIX_FRAMEBUFFER_EFFECTS)
RGB_MATRIX_TYPING_HEATMAP, // How hot is your WPM!
RGB_MATRIX_DIGITAL_RAIN, // That famous computer simulation
@@ -473,7 +507,9 @@ You can disable a single effect by defining `DISABLE_[EFFECT_NAME]` in your `con
|`#define DISABLE_RGB_MATRIX_JELLYBEAN_RAINDROPS` |Disables `RGB_MATRIX_JELLYBEAN_RAINDROPS` |
|`#define DISABLE_RGB_MATRIX_HUE_BREATHING` |Disables `RGB_MATRIX_HUE_BREATHING` |
|`#define DISABLE_RGB_MATRIX_HUE_PENDULUM` |Disables `RGB_MATRIX_HUE_PENDULUM` |
-|`#define DISABLE_RGB_MATRIX_HUE_WAVE ` |Disables `RGB_MATRIX_HUE_WAVE ` |
+|`#define DISABLE_RGB_MATRIX_HUE_WAVE` |Disables `RGB_MATRIX_HUE_WAVE` |
+|`#define DISABLE_RGB_MATRIX_FRACTAL` |Disables `RGB_MATRIX_FRACTAL` |
+|`#define DISABLE_RGB_MATRIX_PIXEL_RAIN ` |Disables `RGB_MATRIX_PIXEL_RAIN ` |
|`#define DISABLE_RGB_MATRIX_TYPING_HEATMAP` |Disables `RGB_MATRIX_TYPING_HEATMAP` |
|`#define DISABLE_RGB_MATRIX_DIGITAL_RAIN` |Disables `RGB_MATRIX_DIGITAL_RAIN` |
|`#define DISABLE_RGB_MATRIX_SOLID_REACTIVE_SIMPLE` |Disables `RGB_MATRIX_SOLID_REACTIVE_SIMPLE` |
@@ -537,7 +573,7 @@ static bool my_cool_effect(effect_params_t* params) {
for (uint8_t i = led_min; i < led_max; i++) {
rgb_matrix_set_color(i, 0xff, 0xff, 0x00);
}
- return led_max < DRIVER_LED_TOTAL;
+ return rgb_matrix_check_finished_leds(led_max);
}
// e.g: A more complex effect, relying on external methods and state, with
@@ -551,8 +587,7 @@ static bool my_cool_effect2_complex_run(effect_params_t* params) {
for (uint8_t i = led_min; i < led_max; i++) {
rgb_matrix_set_color(i, 0xff, some_global_state++, 0xff);
}
-
- return led_max < DRIVER_LED_TOTAL;
+ return rgb_matrix_check_finished_leds(led_max);
}
static bool my_cool_effect2(effect_params_t* params) {
if (params->init) my_cool_effect2_complex_init(params);
@@ -694,7 +729,7 @@ Where `28` is an unused index from `eeconfig.h`.
### Indicators :id=indicators
-If you want to set custom indicators, such as an LED for Caps Lock, or layer indication, you can use the `rgb_matrix_indicators_kb` or `rgb_matrix_indicators_user` function for that:
+If you want to set custom indicators, such as an LED for Caps Lock, or layer indication, you can use the `rgb_matrix_indicators_kb` or `rgb_matrix_indicators_user` function for that:
```c
void rgb_matrix_indicators_kb(void) {
rgb_matrix_set_color(index, red, green, blue);
@@ -749,18 +784,18 @@ This example sets the modifiers to be a specific color based on the layer state.
```c
void rgb_matrix_indicators_advanced_user(uint8_t led_min, uint8_t led_max) {
HSV hsv = {0, 255, 255};
-
+
if (layer_state_is(layer_state, 2)) {
hsv = {130, 255, 255};
} else {
hsv = {30, 255, 255};
}
-
+
if (hsv.v > rgb_matrix_get_val()) {
hsv.v = rgb_matrix_get_val();
}
RGB rgb = hsv_to_rgb(hsv);
-
+
for (uint8_t i = led_min; i <= led_max; i++) {
if (HAS_FLAGS(g_led_config.flags[i], 0x01)) { // 0x01 == LED_FLAG_MODIFIER
rgb_matrix_set_color(i, rgb.r, rgb.g, rgb.b);
@@ -769,7 +804,7 @@ void rgb_matrix_indicators_advanced_user(uint8_t led_min, uint8_t led_max) {
}
```
-If you want to indicate a Host LED status (caps lock, num lock, etc), you can use something like this to light up the caps lock key:
+If you want to indicate a Host LED status (caps lock, num lock, etc), you can use something like this to light up the caps lock key:
```c
void rgb_matrix_indicators_advanced_user(uint8_t led_min, uint8_t led_max) {