diff options
Diffstat (limited to 'docs/feature_pointing_device.md')
| -rw-r--r-- | docs/feature_pointing_device.md | 57 |
1 files changed, 40 insertions, 17 deletions
diff --git a/docs/feature_pointing_device.md b/docs/feature_pointing_device.md index 02c1e64a31..70129dfc9a 100644 --- a/docs/feature_pointing_device.md +++ b/docs/feature_pointing_device.md @@ -72,7 +72,6 @@ The Analog Joystick is an analog (ADC) driven sensor. There are a variety of jo |`ANALOG_JOYSTICK_SPEED_MAX` | (Optional) The maximum value used for motion. | `2` | |`ANALOG_JOYSTICK_CLICK_PIN` | (Optional) The pin wired up to the press switch of the analog stick. | _not defined_ | - ### Cirque Trackpad To use the Cirque Trackpad sensor, add this to your `rules.mk`: @@ -90,29 +89,52 @@ POINTING_DEVICE_DRIVER = cirque_pinnacle_spi This supports the Cirque Pinnacle 1CA027 Touch Controller, which is used in the TM040040, TM035035 and the TM023023 trackpads. These are I2C or SPI compatible, and both configurations are supported. -| Setting | Description | Default | -|---------------------------------|---------------------------------------------------------------------------------|-----------------------| -|`CIRQUE_PINNACLE_X_LOWER` | (Optional) The minimum reachable X value on the sensor. | `127` | -|`CIRQUE_PINNACLE_X_UPPER` | (Optional) The maximum reachable X value on the sensor. | `1919` | -|`CIRQUE_PINNACLE_Y_LOWER` | (Optional) The minimum reachable Y value on the sensor. | `63` | -|`CIRQUE_PINNACLE_Y_UPPER` | (Optional) The maximum reachable Y value on the sensor. | `1471` | -|`CIRQUE_PINNACLE_TAPPING_TERM` | (Optional) Length of time that a touch can be to be considered a tap. | `TAPPING_TERM`/`200` | -|`CIRQUE_PINNACLE_TOUCH_DEBOUNCE` | (Optional) Length of time that a touch can be to be considered a tap. | `TAPPING_TERM`/`200` | +| Setting | Description | Default | +|-------------------------------- |------------------------------------------------------------|--------------------| +|`CIRQUE_PINNACLE_X_LOWER` | (Optional) The minimum reachable X value on the sensor. | `127` | +|`CIRQUE_PINNACLE_X_UPPER` | (Optional) The maximum reachable X value on the sensor. | `1919` | +|`CIRQUE_PINNACLE_Y_LOWER` | (Optional) The minimum reachable Y value on the sensor. | `63` | +|`CIRQUE_PINNACLE_Y_UPPER` | (Optional) The maximum reachable Y value on the sensor. | `1471` | +|`CIRQUE_PINNACLE_DIAMETER_MM` | (Optional) Diameter of the trackpad sensor in millimeters. | `40` | +|`CIRQUE_PINNACLE_ATTENUATION` | (Optional) Sets the attenuation of the sensor data. | `ADC_ATTENUATE_4X` | +|`CIRQUE_PINNACLE_CURVED_OVERLAY` | (Optional) Applies settings tuned for curved overlay. | _not defined_ | + +**`CIRQUE_PINNACLE_ATTENUATION`** is a measure of how much data is suppressed in regards to sensitivity. The higher the attenuation, the less sensitive the touchpad will be. + +Default attenuation is set to 4X, although if you are using a thicker overlay (such as the curved overlay) you will want a lower attenuation such as 2X. The possible values are: +* `ADC_ATTENUATE_4X`: Least sensitive +* `ADC_ATTENUATE_3X` +* `ADC_ATTENUATE_2X` +* `ADC_ATTENUATE_1X`: Most sensitive | I2C Setting | Description | Default | |--------------------------|---------------------------------------------------------------------------------|---------| |`CIRQUE_PINNACLE_ADDR` | (Required) Sets the I2C Address for the Cirque Trackpad | `0x2A` | |`CIRQUE_PINNACLE_TIMEOUT` | (Optional) The timeout for i2c communication with the trackpad in milliseconds. | `20` | -| SPI Setting | Description | Default | -|-------------------------------|------------------------------------------------------------------------|---------------| -|`CIRQUE_PINNACLE_CLOCK_SPEED` | (Optional) Sets the clock speed that the sensor runs at. | `1000000` | -|`CIRQUE_PINNACLE_SPI_LSBFIRST` | (Optional) Sets the Least/Most Significant Byte First setting for SPI. | `false` | -|`CIRQUE_PINNACLE_SPI_MODE` | (Optional) Sets the SPI Mode for the sensor. | `1` | -|`CIRQUE_PINNACLE_SPI_DIVISOR` | (Optional) Sets the SPI Divisor used for SPI communication. | _varies_ | -|`CIRQUE_PINNACLE_SPI_CS_PIN` | (Required) Sets the Cable Select pin connected to the sensor. | _not defined_ | +| SPI Setting | Description | Default | +|-------------------------------|------------------------------------------------------------------------|----------------| +|`CIRQUE_PINNACLE_CLOCK_SPEED` | (Optional) Sets the clock speed that the sensor runs at. | `1000000` | +|`CIRQUE_PINNACLE_SPI_LSBFIRST` | (Optional) Sets the Least/Most Significant Byte First setting for SPI. | `false` | +|`CIRQUE_PINNACLE_SPI_MODE` | (Optional) Sets the SPI Mode for the sensor. | `1` | +|`CIRQUE_PINNACLE_SPI_DIVISOR` | (Optional) Sets the SPI Divisor used for SPI communication. | _varies_ | +|`CIRQUE_PINNACLE_SPI_CS_PIN` | (Required) Sets the Cable Select pin connected to the sensor. | _not defined_ | + +Default Scaling is 1024. Actual CPI depends on trackpad diameter. + +Also see the `POINTING_DEVICE_TASK_THROTTLE_MS`, which defaults to 10ms when using Cirque Pinnacle, which matches the internal update rate of the position registers (in standard configuration). Advanced configuration for pen/stylus usage might require lower values. + +#### Cirque Trackpad gestures + +| Gesture Setting | Description | Default | +|-----------------------------------------------|--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------|----------------------| +|`POINTING_DEVICE_GESTURES_CURSOR_GLIDE_ENABLE` | (Optional) Enable inertial cursor. Cursor continues moving after a flick gesture and slows down by kinetic friction | _not defined_ | +|`CIRQUE_PINNACLE_CIRCULAR_SCROLL_ENABLE` | (Optional) Enable circular scroll. Touch originating in outer ring can trigger scroll by moving along the perimeter. Near side triggers vertical scroll and far side triggers horizontal scroll. | _not defined_ | +|`CIRQUE_PINNACLE_TAP_ENABLE` | (Optional) Enable tap to click. This currently only works on the master side. | _not defined_ | +|`CIRQUE_PINNACLE_TAPPING_TERM` | (Optional) Length of time that a touch can be to be considered a tap. | `TAPPING_TERM`/`200` | +|`CIRQUE_PINNACLE_TOUCH_DEBOUNCE` | (Optional) Length of time that a touch can be to be considered a tap. | `TAPPING_TERM`/`200` | -Default Scaling/CPI is 1024. +**`POINTING_DEVICE_GESTURES_CURSOR_GLIDE_ENABLE`** is not specific to Cirque trackpad; any pointing device with a lift/contact status can integrate this gesture into its driver. e.g. PMW3360 can use Lift_Stat from Motion register. Note that `POINTING_DEVICE_MOTION_PIN` cannot be used with this feature; continuous polling of `pointing_device_get_report()` is needed to generate glide reports. ### Pimoroni Trackball @@ -259,6 +281,7 @@ The following configuration options are only available when using `SPLIT_POINTIN |`POINTING_DEVICE_ROTATION_270_RIGHT` | (Optional) Rotates the X and Y data by 270 degrees. | _not defined_ | |`POINTING_DEVICE_INVERT_X_RIGHT` | (Optional) Inverts the X axis report. | _not defined_ | |`POINTING_DEVICE_INVERT_Y_RIGHT` | (Optional) Inverts the Y axis report. | _not defined_ | +|`MOUSE_EXTENDED_REPORT` | (Optional) Enables support for extended mouse reports. (-32767 to 32767, instead of just -127 to 127) | !> If there is a `_RIGHT` configuration option or callback, the [common configuration](feature_pointing_device.md?id=common-configuration) option will work for the left. For correct left/right detection you should setup a [handedness option](feature_split_keyboard?id=setting-handedness), `EE_HANDS` is usually a good option for an existing board that doesn't do handedness by hardware. |