diff options
Diffstat (limited to 'converter')
| -rw-r--r-- | converter/ps2_usb/Makefile | 42 | ||||
| -rw-r--r-- | converter/ps2_usb/Makefile.jis (renamed from converter/ps2_usb/Makefile.pjrc_usart) | 42 | ||||
| -rw-r--r-- | converter/ps2_usb/Makefile.vusb | 16 | ||||
| -rw-r--r-- | converter/ps2_usb/README | 116 | ||||
| -rw-r--r-- | converter/ps2_usb/README.vusb | 37 | ||||
| -rw-r--r-- | converter/ps2_usb/config.h (renamed from converter/ps2_usb/config_vusb.h) | 107 | ||||
| -rw-r--r-- | converter/ps2_usb/config_pjrc.h | 59 | ||||
| -rw-r--r-- | converter/ps2_usb/config_pjrc_usart.h | 91 | ||||
| -rw-r--r-- | converter/ps2_usb/keymap_jis.c | 297 | ||||
| -rw-r--r-- | converter/ps2_usb/usbconfig.h | 1 |
10 files changed, 495 insertions, 313 deletions
diff --git a/converter/ps2_usb/Makefile b/converter/ps2_usb/Makefile index 1278a74be7..0c6442374c 100644 --- a/converter/ps2_usb/Makefile +++ b/converter/ps2_usb/Makefile @@ -1,10 +1,5 @@ -# -# Makefile for PJRC Teensy -# - - # Target file name (without extension). -TARGET = ps2_usb_pjrc +TARGET = ps2_usb # Directory common source filess exist TOP_DIR = ../.. @@ -12,14 +7,6 @@ TOP_DIR = ../.. # Directory keyboard dependent files exist TARGET_DIR = . -# keyboard dependent files -SRC = keymap.c \ - matrix.c \ - led.c \ - ps2.c - -CONFIG_H = config_pjrc.h - # MCU name, you MUST set this to match the board you are using # type "make clean" after changing this, so all files will be rebuilt @@ -44,6 +31,33 @@ MOUSEKEY_ENABLE = yes # Mouse keys EXTRAKEY_ENABLE = yes # Audio control and System control NKRO_ENABLE = yes # USB Nkey Rollover +PS2_USE_USART = yes # uses hardware USART engine for PS/2 signal receive(recomened) +#PS2_USE_INT = yes # uses external interrupt for falling edge of PS/2 clock pin +#PS2_USE_BUSYWAIT = yes # uses primitive reference code + + +# keyboard dependent files +SRC = keymap.c \ + matrix.c \ + led.c + + +ifdef PS2_USE_USART + SRC += protocol/ps2_usart.c + OPT_DEFS += -DPS2_USE_USART +endif +ifdef PS2_USE_INT + SRC += protocol/ps2.c + OPT_DEFS += -DPS2_USE_INT +endif +ifdef PS2_USE_BUSYWAIT + SRC += protocol/ps2.c + OPT_DEFS += -DPS2_USE_BUSYWAIT +endif + + +#CONFIG_H = config_pjrc_usart.h +CONFIG_H = config.h #---------------- Programming Options -------------------------- diff --git a/converter/ps2_usb/Makefile.pjrc_usart b/converter/ps2_usb/Makefile.jis index dd74712e48..4e091e8e2d 100644 --- a/converter/ps2_usb/Makefile.pjrc_usart +++ b/converter/ps2_usb/Makefile.jis @@ -1,10 +1,5 @@ -# -# Makefile for PJRC Teensy -# - - # Target file name (without extension). -TARGET = ps2_usb_pjrc_usart +TARGET = ps2_usb_jis # Directory common source filess exist TOP_DIR = ../.. @@ -12,14 +7,6 @@ TOP_DIR = ../.. # Directory keyboard dependent files exist TARGET_DIR = . -# keyboard dependent files -SRC = keymap.c \ - matrix.c \ - led.c \ - ps2_usart.c - -CONFIG_H = config_pjrc_usart.h - # MCU name, you MUST set this to match the board you are using # type "make clean" after changing this, so all files will be rebuilt @@ -44,6 +31,33 @@ MOUSEKEY_ENABLE = yes # Mouse keys EXTRAKEY_ENABLE = yes # Audio control and System control NKRO_ENABLE = yes # USB Nkey Rollover +#PS2_USE_USART = yes # uses hardware USART engine for PS/2 signal receive(recomened) +#PS2_USE_INT = yes # uses external interrupt for falling edge of PS/2 clock pin +PS2_USE_BUSYWAIT = yes # uses primitive reference code + + +# keyboard dependent files +SRC = keymap_jis.c \ + matrix.c \ + led.c + + +ifdef PS2_USE_USART + SRC += protocol/ps2_usart.c + OPT_DEFS += -DPS2_USE_USART +endif +ifdef PS2_USE_INT + SRC += protocol/ps2.c + OPT_DEFS += -DPS2_USE_INT +endif +ifdef PS2_USE_BUSYWAIT + SRC += protocol/ps2.c + OPT_DEFS += -DPS2_USE_BUSYWAIT +endif + + +#CONFIG_H = config_pjrc_usart.h +CONFIG_H = config.h #---------------- Programming Options -------------------------- diff --git a/converter/ps2_usb/Makefile.vusb b/converter/ps2_usb/Makefile.vusb index b08d30d574..d449e1e40f 100644 --- a/converter/ps2_usb/Makefile.vusb +++ b/converter/ps2_usb/Makefile.vusb @@ -1,8 +1,3 @@ -# -# Makefile for V-USB -# - - # Target file name (without extension). TARGET = ps2_usb_vusb @@ -15,15 +10,18 @@ TARGET_DIR = . # keyboard dependent files SRC = keymap.c \ matrix.c \ - led.c \ - ps2_usart.c + led.c + +# Use USART for PS/2. With V-USB INT and BUSYWAIT code is not useful. +SRC += protocol/ps2_usart.c +OPT_DEFS += -DPS2_USE_USART -CONFIG_H = config_vusb.h +CONFIG_H = config.h # V-USB debug level: To use ps2_usart.c level must be 0 # ps2_usart.c requires USART to receive PS/2 signal. -OPT_DEFS = -DDEBUG_LEVEL=0 +OPT_DEFS += -DDEBUG_LEVEL=0 # MCU name, you MUST set this to match the board you are using diff --git a/converter/ps2_usb/README b/converter/ps2_usb/README index c10393e5e7..cb7ba55551 100644 --- a/converter/ps2_usb/README +++ b/converter/ps2_usb/README @@ -1,7 +1,7 @@ PS/2 to USB keyboard converter ============================== -This firmware converts PS/2 keyboard protocol to USB and for now supports only Scan Code Set 2. -This will works on USB AVR(ATMega32U4, AT90USB) or V-USB. +This firmware converts PS/2 keyboard protocol to USB and supports only Scan Code Set 2. +This will works on USB AVR(ATMega32U4, AT90USB) or V-USB(ATMega168, 328...). Features @@ -19,25 +19,29 @@ Keymap customization PS/2 signal handling implementations ------------------------------------ Following three methods are used to implement PS/2 signal handling. -a. Simple and stupid wait & read loop(intensive use of cycles) - This is implemented with (expected) portable C code for reference. See ps2.c. -b. Interrupt driven - See ps2_intr.c -c. Using USART hardware module(no cycle needed) - This uses AVR USART function to recevie PS/2 signal and be used in V-USB converter. - See ps2_usart.c. - - -Build Converter ---------------- -Connect PS/2 keyboard into Teensy with 4 lines(Vcc, GND, Data, Clock). -For a. Simple and stupid and b. Interrupt implementaion: - By default Clock is on PF0 and Data on PF1. - You can change this pin configuration by editing config_pjrc.h. - In this photo Vcc is yellow, GND is green, Data is red and Clock is black. - http://img17.imageshack.us/img17/7243/201101181933.jpg -For c. USART implementation: - In case of Teensny(ATMega32u4) CLock is on PD5 and Data on PD2. +a. Simple and stupid busy-wait(ps2.c) + This is expected to implemented with portable C code for reference. +b. Interrupt driven(ps2.c) + Uses external interrupt to detect falling edge of clock line. +c. USART hardware module(ps2_usart.c) + Uses AVR USART engine to recevie PS/2 signal. Recomended and default. + This is required to work with V-USB, preceding two methods tend to + miss signal edges while V-USB handles USB. + +To select method edit Makefile. + + +Connect Wires +------------- +In case of Teensy2.0(ATMega32U4): +0. Connect Vcc and GND. +1. Connect Clock and Data line. + For a. Clock is on PF0 and Data on PF1. + For b. Clock is on PD1 and Data on PD2. + For c. Clock is on PD5 and Data on PD2. +2. Optionally you need pull-up register. 1K-10K Ohm is OK. + +To change pin configuration edit config.h. Build Frimware @@ -45,12 +49,12 @@ Build Frimware 1. Edit Makefile for build options and MCU setting. Use 'atmega32u4' for Teensy 2.0 or 'at90usb1286' for Teensy++ 2.0. 2. make - Just type 'make' in a terminal. - Use '-f Makefile.pjrc_intr' option to use b. Interrupt. - Use '-f Makefile.pjrc_usart' option to use c. USART. - Use '-f Makefile.vusb' option to build V-USB converter. -3. program with Teensy Loader. - http://www.pjrc.com/teensy/loader.html + Just type `make` in a terminal. + Use `-f Makefile.vusb` option to build V-USB converter. + Use `-f Makefile.jis` option to use JIS keyboard. +3. program MCU. + In case of Teensy use `Teensy Loader`.(http://www.pjrc.com/teensy/loader.html) + Otherwise you want to use `avrdude` or `dfu-programmer`. Demonstration of Features @@ -83,34 +87,36 @@ Fn layer function: Keymap ------ -You can change a keymap by editing code of keymap.c like following. -How to define the keymap is probably obvious. You can find key symbols in usb_keycodes.h. -To define keymap layer switching may needs a bit of your effort at this time. - - /* Default Layer: plain keymap - * ,---. ,---------------. ,---------------. ,---------------. ,-----------. ,-----------. - * |Esc| |F1 |F2 |F3 |F4 | |F5 |F6 |F7 |F8 | |F9 |F10|F11|F12| |PrS|ScL|Pau| |Pwr|Slp|Wak| - * `---' `---------------' `---------------' `---------------' `-----------' `-----------' - * ,-----------------------------------------------------------. ,-----------. ,---------------. - * | `| 1| 2| 3| 4| 5| 6| 7| 8| 9| 0| -| =|Backspa| |Ins|Hom|PgU| |NmL| /| *| -| - * |-----------------------------------------------------------| |-----------| |---------------| - * |Tab | Q| W| E| R| T| Y| U| I| O| P| [| ]| \| |Del|End|PgD| | 7| 8| 9| | - * |-----------------------------------------------------------| `-----------' |-----------| +| - * |CapsLo| A| S| D| F| G| H| J| K| L| ;| '|Return | | 4| 5| 6| | - * |-----------------------------------------------------------| ,---. |---------------| - * |Shift | Z| X| C| V| B| N| M| ,| ,| /|Shift | |Up | | 1| 2| 3| | - * |-----------------------------------------------------------| ,-----------. |-----------|Ent| - * |Ctrl |Gui |Alt | Space |Alt |Gui |Menu|Ctrl| |Lef|Dow|Rig| | 0| .| | - * `-----------------------------------------------------------' `-----------' `---------------' - */ - KEYMAP( - ESC, F1, F2, F3, F4, F5, F6, F7, F8, F9, F10, F11, F12, PSCR,SLCK,BRK, PWR, F13, F14, - GRV, 1, 2, 3, 4, 5, 6, 7, 8, 9, 0, MINS,EQL, BSPC, INS, HOME,PGUP, NLCK,PSLS,PAST,PMNS, - TAB, Q, W, E, R, T, Y, U, I, O, P, LBRC,RBRC,BSLS, DEL, END, PGDN, P7, P8, P9, - CAPS,A, S, D, F, G, H, J, K, L, SCLN,QUOT, ENT, P4, P5, P6, PPLS, - LSFT,Z, X, C, V, B, N, M, COMM,DOT, SLSH, RSFT, UP, P1, P2, P3, - LCTL,LGUI,LALT, SPC, RALT,RGUI,APP, RCTL, LEFT,DOWN,RGHT, P0, PDOT,PENT - ), +You can change a keymap by editing code of keymap. See common/keycode.h for key symbols. + + +V-USB Support +------------- +You can also use this converter on ATmega(168/328) with V-USB instead of Teensy. +The converter on V-USB lacks some features for now: USB NKRO and System/Media control. + +Circuit +------- + +---+ +---------------+ +USB GND | | ATmega168 | +=== C3 | | +5V <-------+--------+---|Vcc,AVCC | PS/2 + R1 | | ==== +D- <----+--+-----R2-----|INT1 RXD|------->DATA +D+ <----|---+----R3-----|INT0 XCK|------->CLOCK + Z1 Z2 | | ->5V +GND<----+---+--+--+-----|GND | ->GND + | | | | + | C2-+--|XTAL1 | + | X1 | | + +--C3-+--|XTAL2 | + +---------------+ +R1: 1.5K Ohm +R2,R3: 68 Ohm +Z1,Z2: Zenner 3.6V +C1,C2: 22pF +C3: 0.1uF +X1: Crystal 20MHz(16MHz/12MHz) EOF diff --git a/converter/ps2_usb/README.vusb b/converter/ps2_usb/README.vusb deleted file mode 100644 index c92871bcdd..0000000000 --- a/converter/ps2_usb/README.vusb +++ /dev/null @@ -1,37 +0,0 @@ -V-USB Support -============= -You can also use this converter on ATmega(168/328) with V-USB instead of Teensy. -The converter on V-USB lacks some features for now: USB NKRO and System/Media control. - -To build a firmware use Makefile.vusb instead of Makefile. - - -Circuit -------- - +---+ +---------------+ -USB GND | | ATmega168 | -=== C3 | | -5V <-------+--------+---|Vcc,AVCC | PS/2 - R1 | | ==== -D- <----+--+-----R2-----|INT1 RXD|------->DATA -D+ <----|---+----R3-----|INT0 XCK|------->CLOCK - Z1 Z2 | | ->5V -GND<----+---+--+--+-----|GND | ->GND - | | | | - | C2-+--|XTAL1 | - | X1 | | - +--C3-+--|XTAL2 | - +---------------+ -R1: 1.5K Ohm -R2,R3: 68 Ohm -Z1,Z2: Zenner 3.6V -C1,C2: 22pF -C3: 0.1uF -X1: Crystal 20MHz(16MHz/12MHz) - - -This is my V-USB converter on breadboard. -[IMG]http://i.imgur.com/8jJCZl.jpg[/IMG] - - -EOF diff --git a/converter/ps2_usb/config_vusb.h b/converter/ps2_usb/config.h index afd2f7911f..e5d37e429a 100644 --- a/converter/ps2_usb/config_vusb.h +++ b/converter/ps2_usb/config.h @@ -1,5 +1,5 @@ /* -Copyright 2011 Jun Wako <wakojun@gmail.com> +Copyright 2012 Jun Wako <wakojun@gmail.com> This program is free software: you can redistribute it and/or modify it under the terms of the GNU General Public License as published by @@ -18,11 +18,12 @@ along with this program. If not, see <http://www.gnu.org/licenses/>. #ifndef CONFIG_H #define CONFIG_H +#include <avr/interrupt.h> +/* controller configuration */ +#include "controller_teensy.h" #define VENDOR_ID 0xFEED -#define PRODUCT_ID 0x2233 -// TODO: share these strings with usbconfig.h -// Edit usbconfig.h to change these. +#define PRODUCT_ID 0x6512 #define MANUFACTURER t.m.k. #define PRODUCT PS/2 keyboard converter #define DESCRIPTION convert PS/2 keyboard to USB @@ -46,30 +47,62 @@ along with this program. If not, see <http://www.gnu.org/licenses/>. #endif -/* PS/2 lines */ +#ifdef PS2_USE_USART +#if defined(__AVR_ATmega16U4__) || defined(__AVR_ATmega32U4__) +/* XCK for clock line and RXD for data line */ #define PS2_CLOCK_PORT PORTD #define PS2_CLOCK_PIN PIND #define PS2_CLOCK_DDR DDRD -#define PS2_CLOCK_BIT 4 +#define PS2_CLOCK_BIT 5 #define PS2_DATA_PORT PORTD #define PS2_DATA_PIN PIND #define PS2_DATA_DDR DDRD -#define PS2_DATA_BIT 0 +#define PS2_DATA_BIT 2 +/* synchronous, odd parity, 1-bit stop, 8-bit data, sample at falling edge */ +/* set DDR of CLOCK as input to be slave */ +#define PS2_USART_INIT() do { \ + PS2_CLOCK_DDR &= ~(1<<PS2_CLOCK_BIT); \ + PS2_DATA_DDR &= ~(1<<PS2_DATA_BIT); \ + UCSR1C = ((1 << UMSEL10) | \ + (3 << UPM10) | \ + (0 << USBS1) | \ + (3 << UCSZ10) | \ + (0 << UCPOL1)); \ + UCSR1A = 0; \ + UBRR1H = 0; \ + UBRR1L = 0; \ +} while (0) +#define PS2_USART_RX_INT_ON() do { \ + UCSR1B = ((1 << RXCIE1) | \ + (1 << RXEN1)); \ +} while (0) +#define PS2_USART_RX_POLL_ON() do { \ + UCSR1B = (1 << RXEN1); \ +} while (0) +#define PS2_USART_OFF() do { \ + UCSR1C = 0; \ + UCSR1B &= ~((1 << RXEN1) | \ + (1 << TXEN1)); \ +} while (0) +#define PS2_USART_RX_READY (UCSR1A & (1<<RXC1)) +#define PS2_USART_RX_DATA UDR1 +#define PS2_USART_ERROR (UCSR1A & ((1<<FE1) | (1<<DOR1) | (1<<UPE1))) +#define PS2_USART_RX_VECT USART1_RX_vect -// Synchronous USART is used to receive data from keyboard. -// Use RXD pin for PS/2 DATA line and XCK for PS/2 CLOCK. -// NOTE: This is recomended strongly if you use V-USB library. -#define PS2_USE_USART - -// External or Pin Change Interrupt is used to receive data from keyboard. -// Use INT1 or PCINTxx for PS/2 CLOCK line. see below. -//#define PS2_USE_INT - +#elif defined(__AVR_ATmega168__) || defined(__AVR_ATmega168P__) || defined(__AVR_ATmega328P__) +/* XCK for clock line and RXD for data line */ +#define PS2_CLOCK_PORT PORTD +#define PS2_CLOCK_PIN PIND +#define PS2_CLOCK_DDR DDRD +#define PS2_CLOCK_BIT 4 +#define PS2_DATA_PORT PORTD +#define PS2_DATA_PIN PIND +#define PS2_DATA_DDR DDRD +#define PS2_DATA_BIT 0 -#ifdef PS2_USE_USART -// synchronous, odd parity, 1-bit stop, 8-bit data, sample at falling edge -// set DDR of CLOCK as input to be slave +/* synchronous, odd parity, 1-bit stop, 8-bit data, sample at falling edge */ +/* set DDR of CLOCK as input to be slave */ #define PS2_USART_INIT() do { \ PS2_CLOCK_DDR &= ~(1<<PS2_CLOCK_BIT); \ PS2_DATA_DDR &= ~(1<<PS2_DATA_BIT); \ @@ -99,10 +132,20 @@ along with this program. If not, see <http://www.gnu.org/licenses/>. #define PS2_USART_ERROR (UCSR0A & ((1<<FE0) | (1<<DOR0) | (1<<UPE0))) #define PS2_USART_RX_VECT USART_RX_vect #endif +#endif #ifdef PS2_USE_INT -/* INT1 +/* uses INT1 for clock line(ATMega32U4) */ +#define PS2_CLOCK_PORT PORTD +#define PS2_CLOCK_PIN PIND +#define PS2_CLOCK_DDR DDRD +#define PS2_CLOCK_BIT 1 +#define PS2_DATA_PORT PORTD +#define PS2_DATA_PIN PIND +#define PS2_DATA_DDR DDRD +#define PS2_DATA_BIT 2 + #define PS2_INT_INIT() do { \ EICRA |= ((1<<ISC11) | \ (0<<ISC10)); \ @@ -114,20 +157,18 @@ along with this program. If not, see <http://www.gnu.org/licenses/>. EIMSK &= ~(1<<INT1); \ } while (0) #define PS2_INT_VECT INT1_vect -*/ +#endif -/* PCINT20 */ -#define PS2_INT_INIT() do { \ - PCICR |= (1<<PCIE2); \ -} while (0) -#define PS2_INT_ON() do { \ - PCMSK2 |= (1<<PCINT20); \ -} while (0) -#define PS2_INT_OFF() do { \ - PCMSK2 &= ~(1<<PCINT20); \ - PCICR &= ~(1<<PCIE2); \ -} while (0) -#define PS2_INT_VECT PCINT2_vect + +#ifdef PS2_USE_BUSYWAIT +#define PS2_CLOCK_PORT PORTF +#define PS2_CLOCK_PIN PINF +#define PS2_CLOCK_DDR DDRF +#define PS2_CLOCK_BIT 0 +#define PS2_DATA_PORT PORTF +#define PS2_DATA_PIN PINF +#define PS2_DATA_DDR DDRF +#define PS2_DATA_BIT 1 #endif #endif diff --git a/converter/ps2_usb/config_pjrc.h b/converter/ps2_usb/config_pjrc.h deleted file mode 100644 index 883ffab275..0000000000 --- a/converter/ps2_usb/config_pjrc.h +++ /dev/null @@ -1,59 +0,0 @@ -/* -Copyright 2011 Jun Wako <wakojun@gmail.com> - -This program is free software: you can redistribute it and/or modify -it under the terms of the GNU General Public License as published by -the Free Software Foundation, either version 2 of the License, or -(at your option) any later version. - -This program is distributed in the hope that it will be useful, -but WITHOUT ANY WARRANTY; without even the implied warranty of -MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the -GNU General Public License for more details. - -You should have received a copy of the GNU General Public License -along with this program. If not, see <http://www.gnu.org/licenses/>. -*/ - -#ifndef CONFIG_H -#define CONFIG_H - -/* controller configuration */ -#include "controller_teensy.h" - -#define VENDOR_ID 0xFEED -#define PRODUCT_ID 0x6512 -#define MANUFACTURER t.m.k. -#define PRODUCT PS/2 keyboard converter -#define DESCRIPTION convert PS/2 keyboard to USB - - -/* matrix size */ -#define MATRIX_ROWS 32 // keycode bit: 3-0 -#define MATRIX_COLS 8 // keycode bit: 6-4 - - -/* key combination for command */ -#define IS_COMMAND() ( \ - keyboard_report->mods == (MOD_BIT(KB_LSHIFT) | MOD_BIT(KB_RSHIFT)) || \ - keyboard_report->mods == (MOD_BIT(KB_LCTRL) | MOD_BIT(KB_RSHIFT)) \ -) - - -/* mouse keys */ -#ifdef MOUSEKEY_ENABLE -# define MOUSEKEY_DELAY_TIME 255 -#endif - - -/* PS/2 lines */ -#define PS2_CLOCK_PORT PORTF -#define PS2_CLOCK_PIN PINF -#define PS2_CLOCK_DDR DDRF -#define PS2_CLOCK_BIT 0 -#define PS2_DATA_PORT PORTF -#define PS2_DATA_PIN PINF -#define PS2_DATA_DDR DDRF -#define PS2_DATA_BIT 1 - -#endif diff --git a/converter/ps2_usb/config_pjrc_usart.h b/converter/ps2_usb/config_pjrc_usart.h deleted file mode 100644 index 83ddbf7703..0000000000 --- a/converter/ps2_usb/config_pjrc_usart.h +++ /dev/null @@ -1,91 +0,0 @@ -/* -Copyright 2012 Jun Wako <wakojun@gmail.com> - -This program is free software: you can redistribute it and/or modify -it under the terms of the GNU General Public License as published by -the Free Software Foundation, either version 2 of the License, or -(at your option) any later version. - -This program is distributed in the hope that it will be useful, -but WITHOUT ANY WARRANTY; without even the implied warranty of -MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the -GNU General Public License for more details. - -You should have received a copy of the GNU General Public License -along with this program. If not, see <http://www.gnu.org/licenses/>. -*/ - -#ifndef CONFIG_H -#define CONFIG_H - -/* controller configuration */ -#include "controller_teensy.h" - -#define VENDOR_ID 0xFEED -#define PRODUCT_ID 0x6513 -#define MANUFACTURER t.m.k. -#define PRODUCT PS/2 keyboard converter(USART) -#define DESCRIPTION convert PS/2 keyboard to USB - - -/* matrix size */ -#define MATRIX_ROWS 32 // keycode bit: 3-0 -#define MATRIX_COLS 8 // keycode bit: 6-4 - - -/* key combination for command */ -#define IS_COMMAND() ( \ - keyboard_report->mods == (MOD_BIT(KB_LSHIFT) | MOD_BIT(KB_RSHIFT)) || \ - keyboard_report->mods == (MOD_BIT(KB_LCTRL) | MOD_BIT(KB_RSHIFT)) \ -) - - -/* mouse keys */ -#ifdef MOUSEKEY_ENABLE -# define MOUSEKEY_DELAY_TIME 255 -#endif - - -/* PS/2 lines */ -#define PS2_CLOCK_PORT PORTD -#define PS2_CLOCK_PIN PIND -#define PS2_CLOCK_DDR DDRD -#define PS2_CLOCK_BIT 5 -#define PS2_DATA_PORT PORTD -#define PS2_DATA_PIN PIND -#define PS2_DATA_DDR DDRD -#define PS2_DATA_BIT 2 - - -// synchronous, odd parity, 1-bit stop, 8-bit data, sample at falling edge -// set DDR of CLOCK as input to be slave -#define PS2_USART_INIT() do { \ - PS2_CLOCK_DDR &= ~(1<<PS2_CLOCK_BIT); \ - PS2_DATA_DDR &= ~(1<<PS2_DATA_BIT); \ - UCSR1C = ((1 << UMSEL10) | \ - (3 << UPM10) | \ - (0 << USBS1) | \ - (3 << UCSZ10) | \ - (0 << UCPOL1)); \ - UCSR1A = 0; \ - UBRR1H = 0; \ - UBRR1L = 0; \ -} while (0) -#define PS2_USART_RX_INT_ON() do { \ - UCSR1B = ((1 << RXCIE1) | \ - (1 << RXEN1)); \ -} while (0) -#define PS2_USART_RX_POLL_ON() do { \ - UCSR1B = (1 << RXEN1); \ -} while (0) -#define PS2_USART_OFF() do { \ - UCSR1C = 0; \ - UCSR1B &= ~((1 << RXEN1) | \ - (1 << TXEN1)); \ -} while (0) -#define PS2_USART_RX_READY (UCSR1A & (1<<RXC1)) -#define PS2_USART_RX_DATA UDR1 -#define PS2_USART_ERROR (UCSR1A & ((1<<FE1) | (1<<DOR1) | (1<<UPE1))) -#define PS2_USART_RX_VECT USART1_RX_vect - -#endif diff --git a/converter/ps2_usb/keymap_jis.c b/converter/ps2_usb/keymap_jis.c new file mode 100644 index 0000000000..787c9558af --- /dev/null +++ b/converter/ps2_usb/keymap_jis.c @@ -0,0 +1,297 @@ +/* +Copyright 2011 Jun Wako <wakojun@gmail.com> + +This program is free software: you can redistribute it and/or modify +it under the terms of the GNU General Public License as published by +the Free Software Foundation, either version 2 of the License, or +(at your option) any later version. + +This program is distributed in the hope that it will be useful, +but WITHOUT ANY WARRANTY; without even the implied warranty of +MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +GNU General Public License for more details. + +You should have received a copy of the GNU General Public License +along with this program. If not, see <http://www.gnu.org/licenses/>. +*/ + +/* + * Keymap for PS/2 keyboard + */ +#include <stdint.h> +#include <stdbool.h> +#include <avr/pgmspace.h> +#include "usb_keycodes.h" +#include "print.h" +#include "debug.h" +#include "util.h" +#include "keymap.h" + + + + +// Following macros help you to define a keymap with the form of actual keyboard layout. + +/* US layout plus all other various keys */ +#define KEYMAP_ALL( \ + K76,K05,K06,K04,K0C,K03,K0B,K83,K0A,K01,K09,K78,K07, KFC,K7E,KFE, \ + K0E,K16,K1E,K26,K25,K2E,K36,K3D,K3E,K46,K45,K4E,K55,K66, KF0,KEC,KFD, K77,KCA,K7C,K7B, \ + K0D,K15,K1D,K24,K2D,K2C,K35,K3C,K43,K44,K4D,K54,K5B,K5D, KF1,KE9,KFA, K6C,K75,K7D, \ + K58,K1C,K1B,K23,K2B,K34,K33,K3B,K42,K4B,K4C,K52, K5A, K6B,K73,K74,K79, \ + K12,K1A,K22,K21,K2A,K32,K31,K3A,K41,K49,K4A, K59, KF5, K69,K72,K7A, \ + K14,K9F,K11, K29, K91,KA7,KAF,K94, KEB,KF2,KF4, K70, K71,KDA, \ + \ + K61, /* for European ISO */ \ + K51, K13, K6A, K64, K67, /* for Japanese JIS */ \ + K08, K10, K18, K20, K28, K30, K38, K40, K48, K50, K57, K5F, /* F13-24 */ \ + KB7, KBF, KDE, /* System Power, Sleep, Wake */ \ + KA3, KB2, KA1, /* Mute, Volume Up, Volume Down */ \ + KCD, K95, KBB, KB4, KD0, /* Next, Previous, Stop, Pause, Media Select */ \ + KC8, KAB, KC0, /* Mail, Calculator, My Computer */ \ + K90, KBA, KB8, KB0, /* WWW Search, Home, Back, Forward */ \ + KA8, KA0, K98 /* WWW Stop, Refresh, Favorites */ \ +) { \ + { KB_NO, KB_##K01, KB_NO, KB_##K03, KB_##K04, KB_##K05, KB_##K06, KB_##K07 }, \ + { KB_##K08, KB_##K09, KB_##K0A, KB_##K0B, KB_##K0C, KB_##K0D, KB_##K0E, KB_NO }, \ + { KB_##K10, KB_##K11, KB_##K12, KB_##K13, KB_##K14, KB_##K15, KB_##K16, KB_NO }, \ + { KB_##K18, KB_NO, KB_##K1A, KB_##K1B, KB_##K1C, KB_##K1D, KB_##K1E, KB_NO }, \ + { KB_##K20, KB_##K21, KB_##K22, KB_##K23, KB_##K24, KB_##K25, KB_##K26, KB_NO }, \ + { KB_##K28, KB_##K29, KB_##K2A, KB_##K2B, KB_##K2C, KB_##K2D, KB_##K2E, KB_NO }, \ + { KB_##K30, KB_##K31, KB_##K32, KB_##K33, KB_##K34, KB_##K35, KB_##K36, KB_NO }, \ + { KB_##K38, KB_NO, KB_##K3A, KB_##K3B, KB_##K3C, KB_##K3D, KB_##K3E, KB_NO }, \ + { KB_##K40, KB_##K41, KB_##K42, KB_##K43, KB_##K44, KB_##K45, KB_##K46, KB_NO }, \ + { KB_##K48, KB_##K49, KB_##K4A, KB_##K4B, KB_##K4C, KB_##K4D, KB_##K4E, KB_NO }, \ + { KB_##K50, KB_##K51, KB_##K52, KB_NO, KB_##K54, KB_##K55, KB_NO, KB_##K57 }, \ + { KB_##K58, KB_##K59, KB_##K5A, KB_##K5B, KB_NO, KB_##K5D, KB_NO, KB_##K5F }, \ + { KB_NO, KB_##K61, KB_NO, KB_NO, KB_##K64, KB_NO, KB_##K66, KB_##K67 }, \ + { KB_NO, KB_##K69, KB_##K6A, KB_##K6B, KB_##K6C, KB_NO, KB_NO, KB_NO }, \ + { KB_##K70, KB_##K71, KB_##K72, KB_##K73, KB_##K74, KB_##K75, KB_##K76, KB_##K77 }, \ + { KB_##K78, KB_##K79, KB_##K7A, KB_##K7B, KB_##K7C, KB_##K7D, KB_##K7E, KB_NO }, \ + { KB_NO, KB_NO, KB_NO, KB_##K83, KB_NO, KB_NO, KB_NO, KB_NO }, \ + { KB_NO, KB_NO, KB_NO, KB_NO, KB_NO, KB_NO, KB_NO, KB_NO }, \ + { KB_##K90, KB_##K91, KB_NO, KB_NO, KB_##K94, KB_##K95, KB_NO, KB_NO }, \ + { KB_##K98, KB_NO, KB_NO, KB_NO, KB_NO, KB_NO, KB_NO, KB_##K9F }, \ + { KB_##KA0, KB_##KA1, KB_NO, KB_##KA3, KB_NO, KB_NO, KB_NO, KB_##KA7 }, \ + { KB_##KA8, KB_NO, KB_NO, KB_##KAB, KB_NO, KB_NO, KB_NO, KB_##KAF }, \ + { KB_##KB0, KB_NO, KB_##KB2, KB_NO, KB_##KB4, KB_NO, KB_NO, KB_##KB7 }, \ + { KB_##KB8, KB_NO, KB_##KBA, KB_##KBB, KB_NO, KB_NO, KB_NO, KB_##KBF }, \ + { KB_##KC0, KB_NO, KB_NO, KB_NO, KB_NO, KB_NO, KB_NO, KB_NO }, \ + { KB_##KC8, KB_NO, KB_##KCA, KB_NO, KB_NO, KB_##KCD, KB_NO, KB_NO }, \ + { KB_##KD0, KB_NO, KB_NO, KB_NO, KB_NO, KB_NO, KB_NO, KB_NO }, \ + { KB_NO, KB_NO, KB_##KDA, KB_NO, KB_NO, KB_NO, KB_##KDE, KB_NO }, \ + { KB_NO, KB_NO, KB_NO, KB_NO, KB_NO, KB_NO, KB_NO, KB_NO }, \ + { KB_NO, KB_##KE9, KB_NO, KB_##KEB, KB_##KEC, KB_NO, KB_NO, KB_NO }, \ + { KB_##KF0, KB_##KF1, KB_##KF2, KB_NO, KB_##KF4, KB_##KF5, KB_NO, KB_NO }, \ + { KB_NO, KB_NO, KB_##KFA, KB_NO, KB_##KFC, KB_##KFD, KB_##KFE, KB_NO }, \ +} + +/* JIS layout */ +#define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define KEYMAP_JIS_COMPACT( \ + K0E,K16,K1E,K26,K25,K2E,K36,K3D,K3E,K46,K45,K4E,K55,K6A,K66, \ + K0D,K15,K1D,K24,K2D,K2C,K35,K3C,K43,K44,K4D,K54,K5B, \ + K58,K1C,K1B,K23,K2B,K34,K33,K3B,K42,K4B,K4C,K52,K5D, K5A, \ + K12,K1A,K22,K21,K2A,K32,K31,K3A,K41,K49,K4A,K51, K59, \ + K14,K9F,K11, K67,K29,K64,K13, K91,KA7,KAF,K94 \ +) \ +KEYMAP_ALL( \ + ESC,F1, F2, F3, F4, F5, F6, F7, F8, F9, F10,F11,F12, PSCR,SLCK,BRK, \ + K0E,K16,K1E,K26,K25,K2E,K36,K3D,K3E,K46,K45,K4E,K55,K66, INS, HOME,PGUP, NLCK,PSLS,PAST,PMNS, \ + K0D,K15,K1D,K24,K2D,K2C,K35,K3C,K43,K44,K4D,K54,K5B,K5D, DEL, END, PGDN, P7, P8, P9, \ + K58,K1C,K1B,K23,K2B,K34,K33,K3B,K42,K4B,K4C,K52, K5A, P4, P5, P6, PPLS, \ + K12,K1A,K22,K21,K2A,K32,K31,K3A,K41,K49,K4A, K59, UP, P1, P2, P3, \ + K14,K9F,K11, K29, K91,KA7,KAF,K94, LEFT,DOWN,RGHT, P0, PDOT,PENT, \ + \ + NUBS, \ + K51, K13, K6A, K64, K67, \ + F13, F14, F15, F16, F17, F18, F19, F20, F21, F22, F23, F24, \ + SYSTEM_POWER, SYSTEM_SLEEP, SYSTEM_WAKE, \ + AUDIO_MUTE, AUDIO_VOL_UP, AUDIO_VOL_DOWN, \ + MEDIA_NEXT_TRACK, MEDIA_PREV_TRACK, MEDIA_STOP, MEDIA_PLAY_PAUSE, MEDIA_SELECT, \ + MAIL, CALCULATOR, MY_COMPUTER, \ + WWW_SEARCH, WWW_HOME, WWW_BACK, WWW_FORWARD, \ + WWW_STOP, WWW_REFRESH, WWW_FAVORITES \ +) + + +// Assign Fn key(0-7) to a layer to which switch with the Fn key pressed. +static const uint8_t PROGMEM fn_layer[] = { + 1, // Fn0 + 2, // Fn1 + 1, // Fn2 + 2, // Fn3 + 3, // Fn4 + 4, // Fn5 + 0, // Fn6 + 0 // Fn7 +}; + +// Assign Fn key(0-7) to a keycode sent when release Fn key without use of the layer. +// See layer.c for details. +static const uint8_t PROGMEM fn_keycode[] = { + KB_SCLN, // Fn0 + KB_SLSH, // Fn1 + KB_BSPC, // Fn2 + KB_NO, // Fn3 + KB_NO, // Fn4 + KB_SPC, // Fn5 + KB_NO, // Fn6 + KB_NO // Fn7 +}; + + +// The keymap is a 32*8 byte array which convert a PS/2 scan code into a USB keycode. +// See usb_keycodes.h for USB keycodes. You should omit a 'KB_' prefix of USB keycodes in keymap macro. +// Use KEYMAP_ISO() or KEYMAP_JIS() instead of KEYMAP() if your keyboard is ISO or JIS. +static const uint8_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { + /* 0: JIS LAYOUT + * ,---. ,---------------. ,---------------. ,---------------. ,-----------. ,-----------. + * |Esc| |F1 |F2 |F3 |F4 | |F5 |F6 |F7 |F8 | |F9 |F10|F11|F12| |PrS|ScL|Pau| |Pwr|Slp|Wak| + * `---' `---------------' `---------------' `---------------' `-----------' `-----------' + * ,-----------------------------------------------------------. ,-----------. ,---------------. + * | `| 1| 2| 3| 4| 5| 6| 7| 8| 9| 0| -| =| JY|Bsp| |Ins|Hom|PgU| |NmL| /| *| -| + * |-----------------------------------------------------------| |-----------| |---------------| + * |Tab | Q| W| E| R| T| Y| U| I| O| P| [| ]| Ret | |Del|End|PgD| | 7| 8| 9| | + * |------------------------------------------------------` | `-----------' |-----------| +| + * |CapsLo| A| S| D| F| G| H| J| K| L| ;| :| \| | | 4| 5| 6| | + * |-----------------------------------------------------------| ,---. |---------------| + * |Shift | Z| X| C| V| B| N| M| ,| ,| /| RO|Shift | |Up | | 1| 2| 3| | + * |-----------------------------------------------------------| ,-----------. |-----------|Ent| + * |Ctrl |Gui |Alt |MHEN| Space |HENK|KANA|Alt |Gui |Menu|Ctrl| |Lef|Dow|Rig| | 0| .| | + * `-----------------------------------------------------------' `-----------' `---------------' + */ +/* + KEYMAP_JIS( + ESC, F1, F2, F3, F4, F5, F6, F7, F8, F9, F10, F11, F12, PSCR,SLCK,BRK, + GRV, 1, 2, 3, 4, 5, 6, 7, 8, 9, 0, MINS,EQL, JYEN,BSPC, INS, HOME,PGUP, NLCK,PSLS,PAST,PMNS, + TAB, Q, W, E, R, T, Y, U, I, O, P, LBRC,RBRC, DEL, END, PGDN, P7, P8, P9, + CAPS,A, S, D, F, G, H, J, K, L, SCLN,QUOT,BSLS, ENT, P4, P5, P6, PPLS, + LSFT,Z, X, C, V, B, N, M, COMM,DOT, SLSH,RO, RSFT, UP, P1, P2, P3, + LCTL,LGUI,LALT, MHEN,SPC, HENK,KANA, RALT,RGUI,APP, RCTL, LEFT,DOWN,RGHT, P0, PDOT,PENT + ), +*/ + |