20 files changed, 2351 insertions, 0 deletions
diff --git a/converter/ps2_usb/Makefile b/converter/ps2_usb/Makefile
new file mode 100644
index 0000000000..edcbddfdfa
--- /dev/null
+++ b/converter/ps2_usb/Makefile
@@ -0,0 +1,105 @@
+# 
+# Makefile for Teensy
+#
+# Target file name (without extension).
+TARGET = ps2_usb_lufa
+
+# Directory common source filess exist
+TMK_DIR = ../../tmk_core
+
+# Directory keyboard dependent files exist
+TARGET_DIR = .
+
+# project specific files
+SRC =	keymap_common.c \
+	matrix.c \
+	led.c
+
+ifdef KEYMAP
+    SRC := keymap_$(KEYMAP).c $(SRC)
+else
+    SRC := keymap_plain.c $(SRC)
+endif
+
+CONFIG_H = config.h
+
+
+# MCU name
+#MCU = at90usb1287
+MCU = atmega32u4
+
+# Processor frequency.
+#     This will define a symbol, F_CPU, in all source code files equal to the
+#     processor frequency in Hz. You can then use this symbol in your source code to
+#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
+#     automatically to create a 32-bit value in your source code.
+#
+#     This will be an integer division of F_USB below, as it is sourced by
+#     F_USB after it has run through any CPU prescalers. Note that this value
+#     does not *change* the processor frequency - it should merely be updated to
+#     reflect the processor speed set externally so that the code can use accurate
+#     software delays.
+F_CPU = 16000000
+
+
+#
+# LUFA specific
+#
+# Target architecture (see library "Board Types" documentation).
+ARCH = AVR8
+
+# Input clock frequency.
+#     This will define a symbol, F_USB, in all source code files equal to the
+#     input clock frequency (before any prescaling is performed) in Hz. This value may
+#     differ from F_CPU if prescaling is used on the latter, and is required as the
+#     raw input clock is fed directly to the PLL sections of the AVR for high speed
+#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
+#     at the end, this will be done automatically to create a 32-bit value in your
+#     source code.
+#
+#     If no clock division is performed on the input clock inside the AVR (via the
+#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
+F_USB = $(F_CPU)
+
+# Interrupt driven control endpoint task(+60)
+#OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
+
+
+# Boot Section Size in *bytes*
+#   Teensy halfKay   512
+#   Teensy++ halfKay 1024
+#   Atmel DFU loader 4096
+#   LUFA bootloader  4096
+#   USBaspLoader     2048
+OPT_DEFS += -DBOOTLOADER_SIZE=512
+
+
+# Build Options
+#   comment out to disable the options.
+#
+#BOOTMAGIC_ENABLE = yes	# Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE = yes	# Mouse keys(+4700)
+EXTRAKEY_ENABLE = yes	# Audio control and System control(+450)
+CONSOLE_ENABLE = yes	# Console for debug(+400)
+COMMAND_ENABLE = yes    # Commands for debug and configuration
+NKRO_ENABLE = yes	# USB Nkey Rollover - not yet supported in LUFA
+
+
+# PS/2 Options
+#
+PS2_USE_USART = yes	# uses hardware USART engine for PS/2 signal receive(recomened)
+#PS2_USE_INT = yes	# uses external interrupt for falling edge of PS/2 clock pin
+#PS2_USE_BUSYWAIT = yes	# uses primitive reference code
+
+
+# Optimize size but this may cause error "relocation truncated to fit"
+#EXTRALDFLAGS = -Wl,--relax
+
+# Search Path
+VPATH += $(TARGET_DIR)
+VPATH += $(TMK_DIR)
+
+include $(TMK_DIR)/protocol.mk
+include $(TMK_DIR)/protocol/lufa.mk
+include $(TMK_DIR)/common.mk
+include $(TMK_DIR)/rules.mk
diff --git a/converter/ps2_usb/Makefile.mbed b/converter/ps2_usb/Makefile.mbed
new file mode 100644
index 0000000000..eeb5ad9d5e
--- /dev/null
+++ b/converter/ps2_usb/Makefile.mbed
@@ -0,0 +1,46 @@
+PROJECT = ps2_usb
+
+TMK_DIR = ../../tmk_core
+MBED_DIR = $(TMK_DIR)/mbed-sdk
+
+#VPATH += $(MBED_DIR):$(TMK_DIR)
+vpath %.s .:$(MBED_DIR):$(TMK_DIR)
+vpath %.c .:$(MBED_DIR):$(TMK_DIR)
+vpath %.cpp .:$(MBED_DIR):$(TMK_DIR)
+
+OBJDIR = ./build
+
+OBJECTS = \
+	$(OBJDIR)/protocol/ps2_busywait.o \
+	$(OBJDIR)/protocol/ps2_io_mbed.o \
+	$(OBJDIR)/./keymap_common.o \
+	$(OBJDIR)/./matrix.o \
+	$(OBJDIR)/./led.o \
+	$(OBJDIR)/./main.o
+
+ifdef KEYMAP
+    OBJECTS := $(OBJDIR)/keymap_$(KEYMAP).o $(OBJECTS)
+else
+    OBJECTS := $(OBJDIR)/keymap_plain.o $(OBJECTS)
+endif
+
+CONFIG_H = config_mbed.h
+
+SYS_OBJECTS = 
+
+INCLUDE_PATHS = -I.
+
+LIBRARY_PATHS = 
+LIBRARIES = 
+
+# Build Options
+#   Comment out to disable
+#BOOTMAGIC_ENABLE = yes
+MOUSEKEY_ENABLE = yes
+
+
+#include $(TMK_DIR)/tool/mbed/mk20d50m.mk
+include $(TMK_DIR)/tool/mbed/lpc11u35_501.mk
+include $(TMK_DIR)/tool/mbed/mbed.mk
+include $(TMK_DIR)/tool/mbed/common.mk
+include $(TMK_DIR)/tool/mbed/gcc.mk
diff --git a/converter/ps2_usb/Makefile.pjrc b/converter/ps2_usb/Makefile.pjrc
new file mode 100644
index 0000000000..64319aca88
--- /dev/null
+++ b/converter/ps2_usb/Makefile.pjrc
@@ -0,0 +1,75 @@
+# Target file name (without extension).
+TARGET = ps2_usb_pjrc
+
+# Directory common source filess exist
+TMK_DIR = ../../tmk_core
+
+# Directory keyboard dependent files exist
+TARGET_DIR = .
+
+# keyboard dependent files
+SRC =   keymap_common.c \
+	matrix.c \
+	led.c
+
+ifdef KEYMAP
+    SRC := keymap_$(KEYMAP).c $(SRC)
+else
+    SRC := keymap_plain.c $(SRC)
+endif
+
+CONFIG_H = config.h
+
+
+# MCU name, you MUST set this to match the board you are using
+# type "make clean" after changing this, so all files will be rebuilt
+#MCU = at90usb162       # Teensy 1.0
+MCU = atmega32u4       # Teensy 2.0
+#MCU = at90usb646       # Teensy++ 1.0
+#MCU = at90usb1286      # Teensy++ 2.0
+
+
+# Processor frequency.
+#   Normally the first thing your program should do is set the clock prescaler,
+#   so your program will run at the correct speed.  You should also set this
+#   variable to same clock speed.  The _delay_ms() macro uses this, and many
+#   examples use this variable to calculate timings.  Do not add a "UL" here.
+F_CPU = 16000000
+
+
+# Boot Section Size in *bytes*
+#   Teensy halfKay   512
+#   Teensy++ halfKay 1024
+#   Atmel DFU loader 4096
+#   LUFA bootloader  4096
+#   USBaspLoader     2048
+OPT_DEFS += -DBOOTLOADER_SIZE=4096
+
+
+# Build Options
+#   *Comment out* to disable the options.
+#
+#BOOTMAGIC_ENABLE = yes	# Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE = yes	# Mouse keys
+EXTRAKEY_ENABLE = yes	# Audio control and System control
+CONSOLE_ENABLE = yes	# Console for debug(+400)
+COMMAND_ENABLE = yes    # Commands for debug and configuration
+NKRO_ENABLE = yes	# USB Nkey Rollover
+
+
+# PS/2 Options
+#
+#PS2_USE_USART = yes	# uses hardware USART engine for PS/2 signal receive(recomened)
+#PS2_USE_INT = yes	# uses external interrupt for falling edge of PS/2 clock pin
+PS2_USE_BUSYWAIT = yes	# uses primitive reference code
+
+
+# Search Path
+VPATH += $(TARGET_DIR)
+VPATH += $(TMK_DIR)
+
+
+include $(TMK_DIR)/protocol.mk
+include $(TMK_DIR)/protocol/pjrc.mk
+include $(TMK_DIR)/common.mk
+include $(TMK_DIR)/rules.mk
diff --git a/converter/ps2_usb/Makefile.tmk_rev1 b/converter/ps2_usb/Makefile.tmk_rev1
new file mode 100644
index 0000000000..6aaef49969
--- /dev/null
+++ b/converter/ps2_usb/Makefile.tmk_rev1
@@ -0,0 +1,98 @@
+# 
+# Makefile for TMK keyboard converter rev2
+#     https://github.com/tmk/keyboard_converter#pcb-rev1
+#
+# Target file name (without extension).
+TARGET = ps2_usb_tmk_rev1
+
+# Directory common source filess exist
+TMK_DIR = ../../tmk_core
+
+# Directory keyboard dependent files exist
+TARGET_DIR = .
+
+# project specific files
+SRC =	keymap_common.c \
+	matrix.c \
+	led.c
+
+ifdef KEYMAP
+    SRC := keymap_$(KEYMAP).c $(SRC)
+else
+    SRC := keymap_plain.c $(SRC)
+endif
+
+CONFIG_H = config_tmk_rev1.h
+
+
+# MCU name
+MCU = atmega32u4
+
+# Processor frequency.
+#     This will define a symbol, F_CPU, in all source code files equal to the
+#     processor frequency in Hz. You can then use this symbol in your source code to
+#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
+#     automatically to create a 32-bit value in your source code.
+#
+#     This will be an integer division of F_USB below, as it is sourced by
+#     F_USB after it has run through any CPU prescalers. Note that this value
+#     does not *change* the processor frequency - it should merely be updated to
+#     reflect the processor speed set externally so that the code can use accurate
+#     software delays.
+F_CPU = 16000000
+
+
+#
+# LUFA specific
+#
+# Target architecture (see library "Board Types" documentation).
+ARCH = AVR8
+
+# Input clock frequency.
+#     This will define a symbol, F_USB, in all source code files equal to the
+#     input clock frequency (before any prescaling is performed) in Hz. This value may
+#     differ from F_CPU if prescaling is used on the latter, and is required as the
+#     raw input clock is fed directly to the PLL sections of the AVR for high speed
+#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
+#     at the end, this will be done automatically to create a 32-bit value in your
+#     source code.
+#
+#     If no clock division is performed on the input clock inside the AVR (via the
+#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
+F_USB = $(F_CPU)
+
+
+# Boot Section Size in *bytes*
+#   Teensy halfKay   512
+#   Teensy++ halfKay 1024
+#   Atmel DFU loader 4096
+#   LUFA bootloader  4096
+#   USBaspLoader     2048
+OPT_DEFS += -DBOOTLOADER_SIZE=4096
+
+
+# Build Options
+#   comment out to disable the options.
+#
+#BOOTMAGIC_ENABLE = yes	# Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE = yes	# Mouse keys(+4700)
+EXTRAKEY_ENABLE = yes	# Audio control and System control(+450)
+CONSOLE_ENABLE = yes	# Console for debug(+400)
+COMMAND_ENABLE = yes    # Commands for debug and configuration
+#NKRO_ENABLE = yes	# USB Nkey Rollover - not yet supported in LUFA
+
+
+# PS/2 Options
+#
+PS2_USE_USART = yes	# uses hardware USART engine for PS/2 signal receive(recomened)
+#PS2_USE_BUSYWAIT = yes	# uses primitive reference code
+
+
+# Search Path
+VPATH += $(TARGET_DIR)
+VPATH += $(TMK_DIR)
+
+include $(TMK_DIR)/protocol.mk
+include $(TMK_DIR)/protocol/lufa.mk
+include $(TMK_DIR)/common.mk
+include $(TMK_DIR)/rules.mk
diff --git a/converter/ps2_usb/Makefile.tmk_rev2 b/converter/ps2_usb/Makefile.tmk_rev2
new file mode 100644
index 0000000000..5049a22703
--- /dev/null
+++ b/converter/ps2_usb/Makefile.tmk_rev2
@@ -0,0 +1,98 @@
+# 
+# Makefile for TMK keyboard converter rev2
+#     https://github.com/tmk/keyboard_converter#pcb-rev2
+#
+# Target file name (without extension).
+TARGET = ps2_usb_tmk_rev2
+
+# Directory common source filess exist
+TMK_DIR = ../../tmk_core
+
+# Directory keyboard dependent files exist
+TARGET_DIR = .
+
+# project specific files
+SRC =	keymap_common.c \
+	matrix.c \
+	led.c
+
+ifdef KEYMAP
+    SRC := keymap_$(KEYMAP).c $(SRC)
+else
+    SRC := keymap_plain.c $(SRC)
+endif
+
+CONFIG_H = config_tmk_rev2.h
+
+
+# MCU name
+MCU = atmega32u2
+
+# Processor frequency.
+#     This will define a symbol, F_CPU, in all source code files equal to the
+#     processor frequency in Hz. You can then use this symbol in your source code to
+#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
+#     automatically to create a 32-bit value in your source code.
+#
+#     This will be an integer division of F_USB below, as it is sourced by
+#     F_USB after it has run through any CPU prescalers. Note that this value
+#     does not *change* the processor frequency - it should merely be updated to
+#     reflect the processor speed set externally so that the code can use accurate
+#     software delays.
+F_CPU = 16000000
+
+
+#
+# LUFA specific
+#
+# Target architecture (see library "Board Types" documentation).
+ARCH = AVR8
+
+# Input clock frequency.
+#     This will define a symbol, F_USB, in all source code files equal to the
+#     input clock frequency (before any prescaling is performed) in Hz. This value may
+#     differ from F_CPU if prescaling is used on the latter, and is required as the
+#     raw input clock is fed directly to the PLL sections of the AVR for high speed
+#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
+#     at the end, this will be done automatically to create a 32-bit value in your
+#     source code.
+#
+#     If no clock division is performed on the input clock inside the AVR (via the
+#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
+F_USB = $(F_CPU)
+
+
+# Boot Section Size in *bytes*
+#   Teensy halfKay   512
+#   Teensy++ halfKay 1024
+#   Atmel DFU loader 4096
+#   LUFA bootloader  4096
+#   USBaspLoader     2048
+OPT_DEFS += -DBOOTLOADER_SIZE=4096
+
+
+# Build Options
+#   comment out to disable the options.
+#
+#BOOTMAGIC_ENABLE = yes	# Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE = yes	# Mouse keys(+4700)
+EXTRAKEY_ENABLE = yes	# Audio control and System control(+450)
+CONSOLE_ENABLE = yes	# Console for debug(+400)
+COMMAND_ENABLE = yes    # Commands for debug and configuration
+#NKRO_ENABLE = yes	# USB Nkey Rollover - not yet supported in LUFA
+
+
+# PS/2 Options
+#
+PS2_USE_INT = yes	# uses external interrupt for falling edge of PS/2 clock pin
+#PS2_USE_BUSYWAIT = yes	# uses primitive reference code
+
+
+# Search Path
+VPATH += $(TARGET_DIR)
+VPATH += $(TMK_DIR)
+
+include $(TMK_DIR)/protocol.mk
+include $(TMK_DIR)/protocol/lufa.mk
+include $(TMK_DIR)/common.mk
+include $(TMK_DIR)/rules.mk
diff --git a/converter/ps2_usb/Makefile.vusb b/converter/ps2_usb/Makefile.vusb
new file mode 100644
index 0000000000..8af5c5b083
--- /dev/null
+++ b/converter/ps2_usb/Makefile.vusb
@@ -0,0 +1,107 @@
+# Target file name (without extension).
+TARGET = ps2_usb_vusb
+
+# Directory common source filess exist
+TMK_DIR = ../../tmk_core
+
+# Directory keyboard dependent files exist
+TARGET_DIR = .
+
+# keyboard dependent files
+SRC = keymap_common.c \
+	matrix.c \
+	led.c
+
+ifdef KEYMAP
+    SRC := keymap_$(KEYMAP).c $(SRC)
+else
+    SRC := keymap_plain.c $(SRC)
+endif
+
+# Use USART for PS/2. With V-USB INT and BUSYWAIT code is not useful.
+SRC += protocol/ps2_usart.c
+OPT_DEFS += -DPS2_USE_USART
+
+CONFIG_H = config.h
+
+
+# V-USB debug level: To use ps2_usart.c level must be 0
+# ps2_usart.c requires USART to receive PS/2 signal.
+OPT_DEFS += -DDEBUG_LEVEL=0
+
+
+# MCU name, you MUST set this to match the board you are using
+# type "make clean" after changing this, so all files will be rebuilt
+#MCU = at90usb162       # Teensy 1.0
+#MCU = atmega32u4       # Teensy 2.0
+#MCU = at90usb646       # Teensy++ 1.0
+#MCU = at90usb1286      # Teensy++ 2.0
+MCU = atmega168
+
+
+# Processor frequency.
+#   Normally the first thing your program should do is set the clock prescaler,
+#   so your program will run at the correct speed.  You should also set this
+#   variable to same clock speed.  The _delay_ms() macro uses this, and many
+#   examples use this variable to calculate timings.  Do not add a "UL" here.
+F_CPU = 20000000
+
+
+# Build Options
+#   comment out to disable the options.
+#
+MOUSEKEY_ENABLE = yes	# Mouse keys
+EXTRAKEY_ENABLE = yes	# Audio control and System control
+#NKRO_ENABLE = yes	# USB Nkey Rollover
+NO_UART = yes		# UART is unavailable
+
+
+
+#---------------- Programming Options --------------------------
+AVRDUDE = avrdude
+# Type: avrdude -c ? to get a full listing.
+AVRDUDE_PROGRAMMER = usbasp
+AVRDUDE_PORT =
+AVRDUDE_WRITE_FLASH = -U flash:w:$(TARGET).hex
+#AVRDUDE_WRITE_EEPROM = -U eeprom:w:$(TARGET).eep
+
+# Uncomment the following if you want avrdude's erase cycle counter.
+# Note that this counter needs to be initialized first using -Yn,
+# see avrdude manual.
+#AVRDUDE_ERASE_COUNTER = -y
+
+# Uncomment the following if you do /not/ wish a verification to be
+# performed after programming the device.
+#AVRDUDE_NO_VERIFY = -V
+
+# Increase verbosity level.  Please use this when submitting bug
+# reports about avrdude. See <http://savannah.nongnu.org/projects/avrdude> 
+# to submit bug reports.
+#AVRDUDE_VERBOSE = -v -v
+
+#AVRDUDE_FLAGS = -p $(MCU) -P $(AVRDUDE_PORT) -c $(AVRDUDE_PROGRAMMER)
+AVRDUDE_FLAGS = -p $(MCU) -c $(AVRDUDE_PROGRAMMER)
+AVRDUDE_FLAGS += $(AVRDUDE_NO_VERIFY)
+AVRDUDE_FLAGS += $(AVRDUDE_VERBOSE)
+AVRDUDE_FLAGS += $(AVRDUDE_ERASE_COUNTER)
+
+PROGRAM_CMD = $(AVRDUDE) $(AVRDUDE_FLAGS) $(AVRDUDE_WRITE_FLASH) $(AVRDUDE_WRITE_EEPROM)
+
+
+# Boot Section Size in bytes
+#   Teensy halfKay   512
+#   Atmel DFU loader 4096
+#   LUFA bootloader  4096
+#   USBasp           2048
+OPT_DEFS += -DBOOTLOADER_SIZE=2048
+
+
+# Search Path
+VPATH += $(TARGET_DIR)
+VPATH += $(TMK_DIR)
+
+
+include $(TMK_DIR)/protocol.mk
+include $(TMK_DIR)/common.mk
+include $(TMK_DIR)/protocol/vusb.mk
+include $(TMK_DIR)/rules.mk
diff --git a/converter/ps2_usb/README.md b/converter/ps2_usb/README.md
new file mode 100644
index 0000000000..8a535949d8
--- /dev/null
+++ b/converter/ps2_usb/README.md
@@ -0,0 +1,84 @@
+PS/2 to USB keyboard converter
+==============================
+This firmware converts PS/2 keyboard protocol to USB.(It supports Scan Code Set 2.)
+
+
+Connect Wires
+-------------
+In case of Teensy2.0(ATMega32U4):
+
+1. Connect **Vcc** and **GND**.
+2. Connect **Clock** and **Data** line. 
+    - **Interrupt**:   **Clock** is on `PD1` and **Data** on `PD0`.(Recommended. Soarer's converter compatible)
+    - **Busywait**:    **Clock** is on `PD1` and **Data** on `PD0`.
+    - **USART**:       **Clock** is on `PD5` and **Data** on `PD2`.
+3. Optionally you need pull-up resistor. 1K-10K Ohm is OK.
+
+To change pin configuration edit config.h.
+
+
+Build Firmware
+--------------
+For **PJRC Teensy** just run `make`:
+
+    $ make clean
+    $ make
+
+To select keymap:
+
+    $ make clean
+    $ make KEYMAP=[plain|jis|spacefn|...]
+
+After that you will find HEX file `ps2_usb_lufa.hex` in current directory.
+
+
+- For **TMK converter Rev.1** use `make -f Makefile.tmk_rev1` instead of `make` and HEX file is `ps2_usb_tmk_rev1.hex`.
+
+- For **TMK converter Rev.2** use `make -f Makefile.tmk_rev2` instead of `make` and HEX file is `ps2_usb_tmk_rev2.hex`.
+
+
+Keymap
+------
+Several version of keymap are available in advance but you are recommended to define your favorite layout yourself. To define your own keymap create file named `keymap_<name>.c` and see keymap document(you can find in README.md of top directory) and existent keymap files.
+
+
+PS/2 signal handling implementations
+------------------------------------
+Following three methods can be used to implement PS/2 signal handling.
+
+### Simple and stupid busy-wait(ps2_busywait.c)
+    This is expected to implemented with portable C code for reference.
+### Interrupt driven(ps2_interrupt.c)
+    Uses pin interrupt to detect falling edge of clock line.
+### USART hardware module(ps2_usart.c)
+    Uses AVR USART engine to receive PS/2 signal.
+
+To select method edit Makefile.
+
+
+V-USB Support
+-------------
+With V-USB you can use this converter on ATmega(168/328) but it doesn't support NKRO at this time.
+
+Circuit:
+
+                    +---+   +---------------+
+    USB            GND  |   |   ATmega168   |
+    ===                 C3  |               |
+    5V <-------+--------+---|Vcc,AVCC       |        PS/2
+               R1           |               |        ====
+    D- <----+--+-----R2-----|INT1        RXD|------->DATA
+    D+ <----|---+----R3-----|INT0        XCK|------->CLOCK
+            Z1  Z2          |               |      ->5V
+    GND<----+---+--+--+-----|GND            |      ->GND
+                   |  |     |               |
+                   |  C2-+--|XTAL1          |
+                   |     X1 |               |
+                   +--C3-+--|XTAL2          |
+                            +---------------+
+    R1:     1.5K Ohm
+    R2,R3:  68 Ohm
+    Z1,Z2:  Zenner 3.6V
+    C1,C2:  22pF
+    C3:     0.1uF
+    X1:     Crystal 20MHz(16MHz/12MHz)
diff --git a/converter/ps2_usb/config.h b/converter/ps2_usb/config.h
new file mode 100644
index 0000000000..c9bab1b072
--- /dev/null
+++ b/converter/ps2_usb/config.h
@@ -0,0 +1,173 @@
+/*
+Copyright 2012 Jun Wako <wakojun@gmail.com>
+
+This program is free software: you can redistribute it and/or modify
+it under the terms of the GNU General Public License as published by
+the Free Software Foundation, either version 2 of the License, or
+(at your option) any later version.
+
+This program is distributed in the hope that it will be useful,
+but WITHOUT ANY WARRANTY; without even the implied warranty of
+MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+GNU General Public License for more details.
+
+You should have received a copy of the GNU General Public License
+along with this program.  If not, see <http://www.gnu.org/licenses/>.
+*/
+
+#ifndef CONFIG_H
+#define CONFIG_H
+
+#include <avr/interrupt.h>
+
+#define VENDOR_ID       0xFEED
+#define PRODUCT_ID      0x6512
+#define DEVICE_VER      0x0001
+#define MANUFACTURER    t.m.k.
+#define PRODUCT         PS/2 keyboard converter
+#define DESCRIPTION     convert PS/2 keyboard to USB
+
+
+/* matrix size */
+#define MATRIX_ROWS 32  // keycode bit: 3-0
+#define MATRIX_COLS 8   // keycode bit: 6-4
+
+
+/* key combination for command */
+#define IS_COMMAND() ( \
+    keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)) || \
+    keyboard_report->mods == (MOD_BIT(KC_LCTRL) | MOD_BIT(KC_RSHIFT)) \
+)
+
+
+//#define NO_SUSPEND_POWER_DOWN
+
+
+/*
+ * PS/2 Busywait
+ */
+#ifdef PS2_USE_BUSYWAIT
+#define PS2_CLOCK_PORT  PORTD
+#define PS2_CLOCK_PIN   PIND
+#define PS2_CLOCK_DDR   DDRD
+#define PS2_CLOCK_BIT   5
+#define PS2_DATA_PORT   PORTD
+#define PS2_DATA_PIN    PIND
+#define PS2_DATA_DDR    DDRD
+#define PS2_DATA_BIT    2
+#endif
+
+/*
+ * PS/2 Pin interrupt
+ */
+#ifdef PS2_USE_INT
+/* uses INT1 for clock line(ATMega32U4) */
+#define PS2_CLOCK_PORT  PORTD
+#define PS2_CLOCK_PIN   PIND
+#define PS2_CLOCK_DDR   DDRD
+#define PS2_CLOCK_BIT   1
+#define PS2_DATA_PORT   PORTD
+#define PS2_DATA_PIN    PIND
+#define PS2_DATA_DDR    DDRD
+#define PS2_DATA_BIT    2
+#define PS2_INT_INIT()  do {    \
+    EICRA |= ((1<<ISC11) |      \
+              (0<<ISC10));      \
+} while (0)
+#define PS2_INT_ON()  do {      \
+    EIMSK |= (1<<INT1);         \
+} while (0)
+#define PS2_INT_OFF() do {      \
+    EIMSK &= ~(1<<INT1);        \
+} while (0)
+#define PS2_INT_VECT    INT1_vect
+#endif
+
+/*
+ * PS/2 USART
+ */
+#ifdef PS2_USE_USART
+#if defined(__AVR_ATmega16U4__) || defined(__AVR_ATmega32U4__)
+/* XCK for clock line and RXD for data line */
+#define PS2_CLOCK_PORT  PORTD
+#define PS2_CLOCK_PIN   PIND
+#define PS2_CLOCK_DDR   DDRD
+#define PS2_CLOCK_BIT   5
+#define PS2_DATA_PORT   PORTD
+#define PS2_DATA_PIN    PIND
+#define PS2_DATA_DDR    DDRD
+#define PS2_DATA_BIT    2
+/* synchronous, odd parity, 1-bit stop, 8-bit data, sample at falling edge */
+/* set DDR of CLOCK as input to be slave */
+#define PS2_USART_INIT() do {   \
+    PS2_CLOCK_DDR &= ~(1<<PS2_CLOCK_BIT);   \
+    PS2_DATA_DDR &= ~(1<<PS2_DATA_BIT);     \
+    UCSR1C = ((1 << UMSEL10) |  \
+              (3 << UPM10)   |  \
+              (0 << USBS1)   |  \
+              (3 << UCSZ10)  |  \
+              (0 << UCPOL1));   \
+    UCSR1A = 0;                 \
+    UBRR1H = 0;                 \
+    UBRR1L = 0;                 \
+} while (0)
+#define PS2_USART_RX_INT_ON() do {  \
+    UCSR1B = ((1 << RXCIE1) |       \
+              (1 << RXEN1));        \
+} while (0)
+#define PS2_USART_RX_POLL_ON() do { \
+    UCSR1B = (1 << RXEN1);          \
+} while (0)
+#define PS2_USART_OFF() do {    \
+    UCSR1C = 0;                 \
+    UCSR1B &= ~((1 << RXEN1) |  \
+                (1 << TXEN1));  \
+} while (0)
+#define PS2_USART_RX_READY      (UCSR1A & (1<<RXC1))
+#define PS2_USART_RX_DATA       UDR1
+#define PS2_USART_ERROR         (UCSR1A & ((1<<FE1) | (1<<DOR1) | (1<<UPE1)))
+#define PS2_USART_RX_VECT       USART1_RX_vect
+#elif defined(__AVR_ATmega168__) || defined(__AVR_ATmega168P__) || defined(__AVR_ATmega328P__)
+/* XCK for clock line and RXD for data line */
+#define PS2_CLOCK_PORT  PORTD
+#define PS2_CLOCK_PIN   PIND
+#define PS2_CLOCK_DDR   DDRD
+#define PS2_CLOCK_BIT   4
+#define PS2_DATA_PORT   PORTD
+#define PS2_DATA_PIN    PIND
+#define PS2_DATA_DDR    DDRD
+#define PS2_DATA_BIT    0
+/* synchronous, odd parity, 1-bit stop, 8-bit data, sample at falling edge */
+/* set DDR of CLOCK as input to be slave */
+#define PS2_USART_INIT() do {   \
+    PS2_CLOCK_DDR &= ~(1<<PS2_CLOCK_BIT);   \
+    PS2_DATA_DDR &= ~(1<<PS2_DATA_BIT);     \
+    UCSR0C = ((1 << UMSEL00) |  \
+              (3 << UPM00)   |  \
+              (0 << USBS0)   |  \
+              (3 << UCSZ00)  |  \
+              (0 << UCPOL0));   \
+    UCSR0A = 0;                 \
+    UBRR0H = 0;                 \
+    UBRR0L = 0;                 \
+} while (0)
+#define PS2_USART_RX_INT_ON() do {  \
+    UCSR0B = ((1 << RXCIE0) |       \
+              (1 << RXEN0));        \
+} while (0)
+#define PS2_USART_RX_POLL_ON() do { \
+    UCSR0B = (1 << RXEN0);          \
+} while (0)
+#define PS2_USART_OFF() do {    \
+    UCSR0C = 0;                 \
+    UCSR0B &= ~((1 << RXEN0) |  \
+                (1 << TXEN0));  \
+} while (0)
+#define PS2_USART_RX_READY      (UCSR0A & (1<<RXC0))
+#define PS2_USART_RX_DATA       UDR0
+#define PS2_USART_ERROR         (UCSR0A & ((1<<FE0) | (1<<DOR0) | (1<<UPE0)))
+#define PS2_USART_RX_VECT       USART_RX_vect
+#endif
+#endif
+
+#endif
diff --git a/converter/ps2_usb/config_mbed.h b/converter/ps2_usb/config_mbed.h
new file mode 100644
index 0000000000..5819763e65
--- /dev/null
+++ b/converter/ps2_usb/config_mbed.h
@@ -0,0 +1,60 @@
+/*
+Copyright 2012 Jun Wako <wakojun@gmail.com>
+
+This program is free software: you can redistribute it and/or modify
+it under the terms of the GNU General Public License as published by
+the Free Software Foundation, either version 2 of the License, or
+(at your option) any later version.
+
+This program is distributed in the hope that it will be useful,
+but WITHOUT ANY WARRANTY; without even the implied warranty of
+MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+GNU General Public License for more details.
+
+You should have received a copy of the GNU General Public License
+along with this program.  If not, see <http://www.gnu.org/licenses/>.
+*/
+
+#ifndef CONFIG_MBED_H
+#define CONFIG_MBED_H
+
+
+#if 0
+// duplicated name against mbed USBDeivce
+#define VENDOR_ID       0xFEED
+#define PRODUCT_ID      0x6512
+#endif
+#define DEVICE_VER      0x0001
+#define MANUFACTURER    t.m.k.
+#define PRODUCT         PS/2 keyboard converter
+#define DESCRIPTION     convert PS/2 keyboard to USB
+
+
+/* matrix size */
+#define MATRIX_ROWS 32  // keycode bit: 3-0
+#define MATRIX_COLS 8   // keycode bit: 6-4
+
+
+/* key combination for command */
+#define IS_COMMAND() ( \
+    keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)) || \
+    keyboard_report->mods == (MOD_BIT(KC_LCTRL) | MOD_BIT(KC_RSHIFT)) \
+)
+
+
+/*
+ * PS/2 Busywait
+ */
+#ifdef PS2_USE_BUSYWAIT
+#   define PS2_CLOCK_PORT  PORTD
+#   define PS2_CLOCK_PIN   PIND
+#   define PS2_CLOCK_DDR   DDRD
+#   define PS2_CLOCK_BIT   5
+#   define PS2_DATA_PORT   PORTD
+#   define PS2_DATA_PIN    PIND
+#   define PS2_DATA_DDR    DDRD
+#   define PS2_DATA_BIT    2
+#endif
+
+
+#endif
diff --git a/converter/ps2_usb/config_tmk_rev1.h b/converter/ps2_usb/config_tmk_rev1.h
new file mode 100644
index 0000000000..75dc97df38
--- /dev/null
+++ b/converter/ps2_usb/config_tmk_rev1.h
@@ -0,0 +1,147 @@
+/*
+Copyright 2012 Jun Wako <wakojun@gmail.com>
+
+This program is free software: you can redistribute it and/or modify
+it under the terms of the GNU General Public License as published by
+the Free Software Foundation, either version 2 of the License, or
+(at your option) any later version.
+
+This program is distributed in the hope that it will be useful,
+but WITHOUT ANY WARRANTY; without even the implied warranty of
+MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+GNU General Public License for more details.
+
+You should have received a copy of the GNU General Public License
+along with this program.  If not, see <http://www.gnu.org/licenses/>.
+*/
+
+#ifndef CONFIG_H
+#define CONFIG_H
+
+#include <avr/interrupt.h>
+
+#define VENDOR_ID       0xFEED
+#define PRODUCT_ID      0x6512
+#define DEVICE_VER      0x0001
+#define MANUFACTURER    t.m.k.
+#define PRODUCT         PS/2 keyboard converter
+#define DESCRIPTION     convert PS/2 keyboard to USB
+
+
+/* matrix size */
+#define MATRIX_ROWS 32  // keycode bit: 3-0
+#define MATRIX_COLS 8   // keycode bit: 6-4
+
+
+/* key combination for command */
+#define IS_COMMAND() ( \
+    keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)) || \
+    keyboard_report->mods == (MOD_BIT(KC_LCTRL) | MOD_BIT(KC_RSHIFT)) \
+)
+
+
+//#define NO_SUSPEND_POWER_DOWN
+
+
+/*
+ * PS/2 Busywait
+ */
+#ifdef PS2_USE_BUSYWAIT
+#define PS2_CLOCK_PORT  PORTD
+#define PS2_CLOCK_PIN   PIND
+#define PS2_CLOCK_DDR   DDRD
+#define PS2_CLOCK_BIT   5
+#define PS2_DATA_PORT