diff options
Diffstat (limited to 'Demos/Host/ClassDriver/MassStorageHost')
| -rw-r--r-- | Demos/Host/ClassDriver/MassStorageHost/Config/LUFAConfig.h | 93 | ||||
| -rw-r--r-- | Demos/Host/ClassDriver/MassStorageHost/MassStorageHost.c | 311 | ||||
| -rw-r--r-- | Demos/Host/ClassDriver/MassStorageHost/MassStorageHost.h | 82 | ||||
| -rw-r--r-- | Demos/Host/ClassDriver/MassStorageHost/MassStorageHost.txt | 68 | ||||
| -rw-r--r-- | Demos/Host/ClassDriver/MassStorageHost/asf.xml | 48 | ||||
| -rw-r--r-- | Demos/Host/ClassDriver/MassStorageHost/doxyfile | 2395 | ||||
| -rw-r--r-- | Demos/Host/ClassDriver/MassStorageHost/makefile | 43 |
7 files changed, 3040 insertions, 0 deletions
diff --git a/Demos/Host/ClassDriver/MassStorageHost/Config/LUFAConfig.h b/Demos/Host/ClassDriver/MassStorageHost/Config/LUFAConfig.h new file mode 100644 index 0000000000..e2b5166f25 --- /dev/null +++ b/Demos/Host/ClassDriver/MassStorageHost/Config/LUFAConfig.h @@ -0,0 +1,93 @@ +/* + LUFA Library + Copyright (C) Dean Camera, 2017. + + dean [at] fourwalledcubicle [dot] com + www.lufa-lib.org +*/ + +/* + Copyright 2017 Dean Camera (dean [at] fourwalledcubicle [dot] com) + + Permission to use, copy, modify, distribute, and sell this + software and its documentation for any purpose is hereby granted + without fee, provided that the above copyright notice appear in + all copies and that both that the copyright notice and this + permission notice and warranty disclaimer appear in supporting + documentation, and that the name of the author not be used in + advertising or publicity pertaining to distribution of the + software without specific, written prior permission. + + The author disclaims all warranties with regard to this + software, including all implied warranties of merchantability + and fitness. In no event shall the author be liable for any + special, indirect or consequential damages or any damages + whatsoever resulting from loss of use, data or profits, whether + in an action of contract, negligence or other tortious action, + arising out of or in connection with the use or performance of + this software. +*/ + +/** \file + * \brief LUFA Library Configuration Header File + * + * This header file is used to configure LUFA's compile time options, + * as an alternative to the compile time constants supplied through + * a makefile. + * + * For information on what each token does, refer to the LUFA + * manual section "Summary of Compile Tokens". + */ + +#ifndef _LUFA_CONFIG_H_ +#define _LUFA_CONFIG_H_ + + #if (ARCH == ARCH_AVR8) + + /* Non-USB Related Configuration Tokens: */ +// #define DISABLE_TERMINAL_CODES + + /* USB Class Driver Related Tokens: */ +// #define HID_HOST_BOOT_PROTOCOL_ONLY +// #define HID_STATETABLE_STACK_DEPTH {Insert Value Here} +// #define HID_USAGE_STACK_DEPTH {Insert Value Here} +// #define HID_MAX_COLLECTIONS {Insert Value Here} +// #define HID_MAX_REPORTITEMS {Insert Value Here} +// #define HID_MAX_REPORT_IDS {Insert Value Here} +// #define NO_CLASS_DRIVER_AUTOFLUSH + + /* General USB Driver Related Tokens: */ +// #define ORDERED_EP_CONFIG + #define USE_STATIC_OPTIONS (USB_OPT_REG_ENABLED | USB_OPT_AUTO_PLL) +// #define USB_DEVICE_ONLY + #define USB_HOST_ONLY + #define USB_STREAM_TIMEOUT_MS 5000 +// #define NO_LIMITED_CONTROLLER_CONNECT +// #define NO_SOF_EVENTS + + /* USB Device Mode Driver Related Tokens: */ +// #define USE_RAM_DESCRIPTORS +// #define USE_FLASH_DESCRIPTORS +// #define USE_EEPROM_DESCRIPTORS +// #define NO_INTERNAL_SERIAL +// #define FIXED_CONTROL_ENDPOINT_SIZE {Insert Value Here} +// #define DEVICE_STATE_AS_GPIOR {Insert Value Here} +// #define FIXED_NUM_CONFIGURATIONS {Insert Value Here} +// #define CONTROL_ONLY_DEVICE +// #define INTERRUPT_CONTROL_ENDPOINT +// #define NO_DEVICE_REMOTE_WAKEUP +// #define NO_DEVICE_SELF_POWER + + /* USB Host Mode Driver Related Tokens: */ +// #define HOST_STATE_AS_GPIOR {Insert Value Here} +// #define USB_HOST_TIMEOUT_MS {Insert Value Here} +// #define HOST_DEVICE_SETTLE_DELAY_MS {Insert Value Here} +// #define NO_AUTO_VBUS_MANAGEMENT +// #define INVERTED_VBUS_ENABLE_LINE + + #else + + #error Unsupported architecture for this LUFA configuration file. + + #endif +#endif diff --git a/Demos/Host/ClassDriver/MassStorageHost/MassStorageHost.c b/Demos/Host/ClassDriver/MassStorageHost/MassStorageHost.c new file mode 100644 index 0000000000..62a4071c3d --- /dev/null +++ b/Demos/Host/ClassDriver/MassStorageHost/MassStorageHost.c @@ -0,0 +1,311 @@ +/* + LUFA Library + Copyright (C) Dean Camera, 2017. + + dean [at] fourwalledcubicle [dot] com + www.lufa-lib.org +*/ + +/* + Copyright 2017 Dean Camera (dean [at] fourwalledcubicle [dot] com) + + Permission to use, copy, modify, distribute, and sell this + software and its documentation for any purpose is hereby granted + without fee, provided that the above copyright notice appear in + all copies and that both that the copyright notice and this + permission notice and warranty disclaimer appear in supporting + documentation, and that the name of the author not be used in + advertising or publicity pertaining to distribution of the + software without specific, written prior permission. + + The author disclaims all warranties with regard to this + software, including all implied warranties of merchantability + and fitness. In no event shall the author be liable for any + special, indirect or consequential damages or any damages + whatsoever resulting from loss of use, data or profits, whether + in an action of contract, negligence or other tortious action, + arising out of or in connection with the use or performance of + this software. +*/ + +/** \file + * + * Main source file for the MassStorageHost demo. This file contains the main tasks of + * the demo and is responsible for the initial application hardware configuration. + */ + +#include "MassStorageHost.h" + +/** LUFA Mass Storage Class driver interface configuration and state information. This structure is + * passed to all Mass Storage Class driver functions, so that multiple instances of the same class + * within a device can be differentiated from one another. + */ +USB_ClassInfo_MS_Host_t FlashDisk_MS_Interface = + { + .Config = + { + .DataINPipe = + { + .Address = (PIPE_DIR_IN | 1), + .Banks = 1, + }, + .DataOUTPipe = + { + .Address = (PIPE_DIR_OUT | 2), + .Banks = 1, + }, + }, + }; + + +/** Main program entry point. This routine configures the hardware required by the application, then + * enters a loop to run the application tasks in sequence. + */ +int main(void) +{ + SetupHardware(); + + puts_P(PSTR(ESC_FG_CYAN "Mass Storage Host Demo running.\r\n" ESC_FG_WHITE)); + + LEDs_SetAllLEDs(LEDMASK_USB_NOTREADY); + GlobalInterruptEnable(); + + for (;;) + { + MassStorageHost_Task(); + + MS_Host_USBTask(&FlashDisk_MS_Interface); + USB_USBTask(); + } +} + +/** Configures the board hardware and chip peripherals for the demo's functionality. */ +void SetupHardware(void) +{ +#if (ARCH == ARCH_AVR8) + /* Disable watchdog if enabled by bootloader/fuses */ + MCUSR &= ~(1 << WDRF); + wdt_disable(); + + /* Disable clock division */ + clock_prescale_set(clock_div_1); +#endif + + /* Hardware Initialization */ + Serial_Init(9600, false); + LEDs_Init(); + USB_Init(); + + /* Create a stdio stream for the serial port for stdin and stdout */ + Serial_CreateStream(NULL); +} + +/** Task to manage an enumerated USB Mass Storage device once connected, to print out + * data from the device. + */ +void MassStorageHost_Task(void) +{ + if (USB_HostState != HOST_STATE_Configured) + return; + + LEDs_SetAllLEDs(LEDMASK_USB_BUSY); + + puts_P(PSTR("Waiting until ready...\r\n")); + + for (;;) + { + uint8_t ErrorCode = MS_Host_TestUnitReady(&FlashDisk_MS_Interface, 0); + + if (!(ErrorCode)) + break; + + /* Check if an error other than a logical command error (device busy) received */ + if (ErrorCode != MS_ERROR_LOGICAL_CMD_FAILED) + { + puts_P(PSTR("Error waiting for device to be ready.\r\n")); + LEDs_SetAllLEDs(LEDMASK_USB_ERROR); + USB_Host_SetDeviceConfiguration(0); + return; + } + } + + puts_P(PSTR("Retrieving Capacity...\r\n")); + + SCSI_Capacity_t DiskCapacity; + if (MS_Host_ReadDeviceCapacity(&FlashDisk_MS_Interface, 0, &DiskCapacity)) + { + puts_P(PSTR("Error retrieving device capacity.\r\n")); + LEDs_SetAllLEDs(LEDMASK_USB_ERROR); + USB_Host_SetDeviceConfiguration(0); + return; + } + + printf_P(PSTR("%lu blocks of %lu bytes.\r\n"), DiskCapacity.Blocks, DiskCapacity.BlockSize); + + uint8_t BlockBuffer[DiskCapacity.BlockSize]; + + if (MS_Host_ReadDeviceBlocks(&FlashDisk_MS_Interface, 0, 0x00000000, 1, DiskCapacity.BlockSize, BlockBuffer)) + { + puts_P(PSTR("Error reading device block.\r\n")); + LEDs_SetAllLEDs(LEDMASK_USB_ERROR); + USB_Host_SetDeviceConfiguration(0); + return; + } + + puts_P(PSTR("\r\nContents of first block:\r\n")); + + for (uint16_t Chunk = 0; Chunk < (DiskCapacity.BlockSize >> 4); Chunk++) + { + uint8_t* ChunkPtr = &BlockBuffer[Chunk << 4]; + + /* Print out the 16 bytes of the chunk in HEX format */ + for (uint8_t ByteOffset = 0; ByteOffset < (1 << 4); ByteOffset++) + { + char CurrByte = *(ChunkPtr + ByteOffset); + printf_P(PSTR("%.2X "), CurrByte); + } + + printf_P(PSTR(" ")); + + /* Print out the 16 bytes of the chunk in ASCII format */ + for (uint8_t ByteOffset = 0; ByteOffset < (1 << 4); ByteOffset++) + { + char CurrByte = *(ChunkPtr + ByteOffset); + putchar(isprint(CurrByte) ? CurrByte : '.'); + } + + printf_P(PSTR("\r\n")); + } + + LEDs_SetAllLEDs(LEDMASK_USB_READY); + USB_Host_SetDeviceConfiguration(0); +} + +/** Event handler for the USB_DeviceAttached event. This indicates that a device has been attached to the host, and + * starts the library USB task to begin the enumeration and USB management process. + */ +void EVENT_USB_Host_DeviceAttached(void) +{ + puts_P(PSTR("Device Attached.\r\n")); + LEDs_SetAllLEDs(LEDMASK_USB_ENUMERATING); +} + +/** Event handler for the USB_DeviceUnattached event. This indicates that a device has been removed from the host, and + * stops the library USB task management process. + */ +void EVENT_USB_Host_DeviceUnattached(void) +{ + puts_P(PSTR("\r\nDevice Unattached.\r\n")); + LEDs_SetAllLEDs(LEDMASK_USB_NOTREADY); +} + +/** Event handler for the USB_DeviceEnumerationComplete event. This indicates that a device has been successfully + * enumerated by the host and is now ready to be used by the application. + */ +void EVENT_USB_Host_DeviceEnumerationComplete(void) +{ + LEDs_SetAllLEDs(LEDMASK_USB_ENUMERATING); + + uint16_t ConfigDescriptorSize; + uint8_t ConfigDescriptorData[512]; + + if (USB_Host_GetDeviceConfigDescriptor(1, &ConfigDescriptorSize, ConfigDescriptorData, + sizeof(ConfigDescriptorData)) != HOST_GETCONFIG_Successful) + { + puts_P(PSTR("Error Retrieving Configuration Descriptor.\r\n")); + LEDs_SetAllLEDs(LEDMASK_USB_ERROR); + return; + } + + if (MS_Host_ConfigurePipes(&FlashDisk_MS_Interface, + ConfigDescriptorSize, ConfigDescriptorData) != MS_ENUMERROR_NoError) + { + puts_P(PSTR("Attached Device Not a Valid Mass Storage Device.\r\n")); + LEDs_SetAllLEDs(LEDMASK_USB_ERROR); + return; + } + + if (USB_Host_SetDeviceConfiguration(1) != HOST_SENDCONTROL_Successful) + { + puts_P(PSTR("Error Setting Device Configuration.\r\n")); + LEDs_SetAllLEDs(LEDMASK_USB_ERROR); + return; + } + + uint8_t MaxLUNIndex; + if (MS_Host_GetMaxLUN(&FlashDisk_MS_Interface, &MaxLUNIndex)) + { + puts_P(PSTR("Error retrieving max LUN index.\r\n")); + LEDs_SetAllLEDs(LEDMASK_USB_ERROR); + USB_Host_SetDeviceConfiguration(0); + return; + } + + printf_P(PSTR("Total LUNs: %d - Using first LUN in device.\r\n"), (MaxLUNIndex + 1)); + + if (MS_Host_ResetMSInterface(&FlashDisk_MS_Interface)) + { + puts_P(PSTR("Error resetting Mass Storage interface.\r\n")); + LEDs_SetAllLEDs(LEDMASK_USB_ERROR); + USB_Host_SetDeviceConfiguration(0); + return; + } + + SCSI_Request_Sense_Response_t SenseData; + if (MS_Host_RequestSense(&FlashDisk_MS_Interface, 0, &SenseData) != 0) + { + puts_P(PSTR("Error retrieving device sense.\r\n")); + LEDs_SetAllLEDs(LEDMASK_USB_ERROR); + USB_Host_SetDeviceConfiguration(0); + return; + } + + if (MS_Host_PreventAllowMediumRemoval(&FlashDisk_MS_Interface, 0, true)) + { + puts_P(PSTR("Error setting Prevent Device Removal bit.\r\n")); + LEDs_SetAllLEDs(LEDMASK_USB_ERROR); + USB_Host_SetDeviceConfiguration(0); + return; + } + + SCSI_Inquiry_Response_t InquiryData; + if (MS_Host_GetInquiryData(&FlashDisk_MS_Interface, 0, &InquiryData)) + { + puts_P(PSTR("Error retrieving device Inquiry data.\r\n")); + LEDs_SetAllLEDs(LEDMASK_USB_ERROR); + USB_Host_SetDeviceConfiguration(0); + return; + } + + printf_P(PSTR("Vendor \"%.8s\", Product \"%.16s\"\r\n"), InquiryData.VendorID, InquiryData.ProductID); + + puts_P(PSTR("Mass Storage Device Enumerated.\r\n")); + LEDs_SetAllLEDs(LEDMASK_USB_READY); +} + +/** Event handler for the USB_HostError event. This indicates that a hardware error occurred while in host mode. */ +void EVENT_USB_Host_HostError(const uint8_t ErrorCode) +{ + USB_Disable(); + + printf_P(PSTR(ESC_FG_RED "Host Mode Error\r\n" + " -- Error Code %d\r\n" ESC_FG_WHITE), ErrorCode); + + LEDs_SetAllLEDs(LEDMASK_USB_ERROR); + for(;;); +} + +/** Event handler for the USB_DeviceEnumerationFailed event. This indicates that a problem occurred while + * enumerating an attached USB device. + */ +void EVENT_USB_Host_DeviceEnumerationFailed(const uint8_t ErrorCode, + const uint8_t SubErrorCode) +{ + printf_P(PSTR(ESC_FG_RED "Dev Enum Error\r\n" + " -- Error Code %d\r\n" + " -- Sub Error Code %d\r\n" + " -- In State %d\r\n" ESC_FG_WHITE), ErrorCode, SubErrorCode, USB_HostState); + + LEDs_SetAllLEDs(LEDMASK_USB_ERROR); +} + diff --git a/Demos/Host/ClassDriver/MassStorageHost/MassStorageHost.h b/Demos/Host/ClassDriver/MassStorageHost/MassStorageHost.h new file mode 100644 index 0000000000..088f5c1400 --- /dev/null +++ b/Demos/Host/ClassDriver/MassStorageHost/MassStorageHost.h @@ -0,0 +1,82 @@ +/* + LUFA Library + Copyright (C) Dean Camera, 2017. + + dean [at] fourwalledcubicle [dot] com + www.lufa-lib.org +*/ + +/* + Copyright 2017 Dean Camera (dean [at] fourwalledcubicle [dot] com) + + Permission to use, copy, modify, distribute, and sell this + software and its documentation for any purpose is hereby granted + without fee, provided that the above copyright notice appear in + all copies and that both that the copyright notice and this + permission notice and warranty disclaimer appear in supporting + documentation, and that the name of the author not be used in + advertising or publicity pertaining to distribution of the + software without specific, written prior permission. + + The author disclaims all warranties with regard to this + software, including all implied warranties of merchantability + and fitness. In no event shall the author be liable for any + special, indirect or consequential damages or any damages + whatsoever resulting from loss of use, data or profits, whether + in an action of contract, negligence or other tortious action, + arising out of or in connection with the use or performance of + this software. +*/ + +/** \file + * + * Header file for MassStorage.c. + */ + +#ifndef _MASS_STORAGE_HOST_H_ +#define _MASS_STORAGE_HOST_H_ + + /* Includes: */ + #include <avr/io.h> + #include <avr/wdt.h> + #include <avr/pgmspace.h> + #include <avr/power.h> + #include <avr/interrupt.h> + #include <ctype.h> + #include <stdio.h> + + #include <LUFA/Drivers/Misc/TerminalCodes.h> + #include <LUFA/Drivers/Peripheral/Serial.h> + #include <LUFA/Drivers/Board/LEDs.h> + #include <LUFA/Drivers/USB/USB.h> + #include <LUFA/Platform/Platform.h> + + /* Macros: */ + /** LED mask for the library LED driver, to indicate that the USB interface is not ready. */ + #define LEDMASK_USB_NOTREADY LEDS_LED1 + + /** LED mask for the library LED driver, to indicate that the USB interface is enumerating. */ + #define LEDMASK_USB_ENUMERATING (LEDS_LED2 | LEDS_LED3) + + /** LED mask for the library LED driver, to indicate that the USB interface is ready. */ + #define LEDMASK_USB_READY (LEDS_LED2 | LEDS_LED4) + + /** LED mask for the library LED driver, to indicate that an error has occurred in the USB interface. */ + #define LEDMASK_USB_ERROR (LEDS_LED1 | LEDS_LED3) + + /** LED mask for the library LED driver, to indicate that the USB interface is busy. */ + #define LEDMASK_USB_BUSY LEDS_LED2 + + /* Function Prototypes: */ + void SetupHardware(void); + void MassStorageHost_Task(void); + + void EVENT_USB_Host_HostError(const uint8_t ErrorCode); + void EVENT_USB_Host_DeviceAttached(void); + void EVENT_USB_Host_DeviceUnattached(void); + void EVENT_USB_Host_DeviceEnumerationFailed(const uint8_t ErrorCode, + const uint8_t SubErrorCode); + void EVENT_USB_Host_DeviceEnumerationComplete(void); + +#endif + diff --git a/Demos/Host/ClassDriver/MassStorageHost/MassStorageHost.txt b/Demos/Host/ClassDriver/MassStorageHost/MassStorageHost.txt new file mode 100644 index 0000000000..4b07261c4f --- /dev/null +++ b/Demos/Host/ClassDriver/MassStorageHost/MassStorageHost.txt @@ -0,0 +1,68 @@ +/** \file + * + * This file contains special DoxyGen information for the generation of the main page and other special + * documentation pages. It is not a project source file. + */ + +/** \mainpage Mass Storage Host Demo + * + * \section Sec_Compat Demo Compatibility: + * + * The following list indicates what microcontrollers are compatible with this demo. + * + * \li Series 7 USB AVRs (AT90USBxxx7) + * + * \section Sec_Info USB Information: + * + * The following table gives a rundown of the USB utilization of this demo. + * + * <table> + * <tr> + * <td><b>USB Mode:</b></td> + * <td>Host</td> + * </tr> + * <tr> + * <td><b>USB Class:</b></td> + * <td>Mass Storage Device</td> + * </tr> + * <tr> + * <td><b>USB Subclass:</b></td> + * <td>Bulk Only</td> + * </tr> + * <tr> + * <td><b>Relevant Standards:</b></td> + * <td>USBIF Mass Storage Standard \n + * USB Bulk-Only Transport Standard \n + * SCSI Primary Commands Specification \n + * SCSI Block Commands Specification</td> + * </tr> + * <tr> + * <td><b>Supported USB Speeds:</b></td> + * <td>Full Speed Mode</td> + * </tr> + * </table> + * + * \section Sec_Description Project Description: + * + * Mass Storage host demonstration application. This gives a simple reference + * application for implementing a USB Mass Storage host, for USB storage devices + * using the standard Mass Storage USB profile. + * + * The first 512 bytes (boot sector) of an attached disk's memory will be dumped + * out of the serial port in HEX and ASCII form when it is attached to the AT90USB1287 + * AVR. The device will then wait for HWB to be pressed, whereupon the entire ASCII contents + * of the disk will be dumped to the serial port. + * + * \section Sec_Options Project Options + * + * The following defines can be found in this demo, which can control the demo behaviour when defined, or changed in value. + * + * <table> + * <tr> + * <td> + * None + * </td> + * </tr> + * </table> + */ + diff --git a/Demos/Host/ClassDriver/MassStorageHost/asf.xml b/Demos/Host/ClassDriver/MassStorageHost/asf.xml new file mode 100644 index 0000000000..54bfe50cc6 --- /dev/null +++ b/Demos/Host/ClassDriver/MassStorageHost/asf.xml @@ -0,0 +1,48 @@ +<asf xmlversion="1.0">
+ <project caption="Mass Storage Host Demo (Class Driver APIs)" id="lufa.demos.host.class.ms.example.avr8">
+ <require idref="lufa.demos.host.class.ms"/>
+ <require idref="lufa.boards.dummy.avr8"/>
+ <generator value="as5_8"/>
+
+ <device-support value="at90usb1287"/>
+ <config name="lufa.drivers.board.name" value="none"/>
+
+ <build type="define" name="F_CPU" value="16000000UL"/>
+ <build type="define" name="F_USB" value="16000000UL"/>
+ </project>
+
+ <module type="application" id="lufa.demos.host.class.ms" caption="Mass Storage Host Demo (Class Driver APIs)">
+ <info type="description" value="summary">
+ Mass Storage Host demo, capable of reading and writing raw 512 byte segments to the device's serial port. This demo uses the user-friendly USB Class Driver APIs to provide a simple, abstracted interface into the USB stack.
+ </info>
+
+ <info type="gui-flag" value="move-to-root"/>
+
+ <info type="keyword" value="Technology">
+ <keyword value="Class Driver APIs"/>
+ <keyword value="USB Host"/>
+ <keyword value="Mass Storage Class"/>
+ </info>
+
+ <device-support-alias value="lufa_avr8"/>
+ <device-support-alias value="lufa_xmega"/>
+ <device-support-alias value="lufa_uc3"/>
+
+ <build type="distribute" subtype="user-file" value="doxyfile"/>
+ <build type="distribute" subtype="user-file" value="MassStorageHost.txt"/>
+
+ <build type="c-source" value="MassStorageHost.c"/>
+ <build type="header-file" value="MassStorageHost.h"/>
+
+ <build type="module-config" subtype="path" value="Config"/>
+ <build type="header-file" value="Config/LUFAConfig.h"/>
+
+ <require idref="lufa.common"/>
+ <require idref="lufa.platform"/>
+ <require idref="lufa.drivers.usb"/>
+ <require idref="lufa.drivers.peripheral.usart"/>
+ <require idref="lufa.drivers.misc.ansi"/>
+ <require idref="lufa.drivers.board"/>
+ <require idref="lufa.drivers.board.leds"/>
+ </module>
+</asf>
diff --git a/Demos/Host/ClassDriver/MassStorageHost/doxyfile b/Demos/Host/ClassDriver/MassStorageHost/doxyfile new file mode 100644 index 0000000000..58657165ca --- /dev/null +++ b/Demos/Host/ClassDriver/MassStorageHost/doxyfile @@ -0,0 +1,2395 @@ +# Doxyfile 1.8.9 + +# This file describes the settings to be used by the documentation system +# doxygen (www.doxygen.org) for a project. +# +# All text after a double hash (##) is considered a comment and is placed in +# front of the TAG it is preceding. +# +# All text after a single hash (#) is considered a comment and will be ignored. +# The format is: +# TAG = value [value, ...] +# For lists, items can also be appended using: +# TAG += value [value, ...] +# Values that contain spaces should be placed between quotes (\" \"). + +#--------------------------------------------------------------------------- +# Project related configuration options +#--------------------------------------------------------------------------- + +# This tag specifies the encoding used for all characters in the config file +# that follow. The default is UTF-8 which is also the encoding used for all text +# before the first occurrence of this tag. Doxygen uses libiconv (or the iconv +# built into libc) for the transcoding. See http://www.gnu.org/software/libiconv +# for the list of possible encodings. +# The default value is: UTF-8. + +DOXYFILE_ENCODING = UTF-8 + +# The PROJECT_NAME tag is a single word (or a sequence of words surrounded by +# double-quotes, unless you are using Doxywizard) that should identify the +# project for which the documentation is generated. This name is used in the +# title of most generated pages and in a few other places. +# The default value is: My Project. + +PROJECT_NAME = "LUFA Library - Mass Storage Host Demo" + +# The PROJECT_NUMBER tag can be used to enter a project or revision number. This +# could be handy for archiving the generated documentation or if some version +# control system is used. + +PROJECT_NUMBER = + +# Using the PROJECT_BRIEF tag one can provide an optional one line description +# for a project that appears at the top of each page and should give viewer a +# quick idea about the purpose of the project. Keep the description short. + +PROJECT_BRIEF = + +# With the PROJECT_LOGO tag one can specify a logo or an icon that is included +# in the documentation. The maximum height of the logo should not exceed 55 +# pixels and the maximum width should not exceed 200 pixels. Doxygen will copy +# the logo to the output directory. + +PROJECT_LOGO = + +# The OUTPUT_DIRECTORY tag is used to specify the (relative or absolute) path +# into which the generated documentation will be written. If a relative path is +# entered, it will be relative to the location where doxygen was started. If +# left blank the current directory will be used. + +OUTPUT_DIRECTORY = ./Documentation/ + +# If the CREATE_SUBDIRS tag is set to YES then doxygen will create 4096 sub- +# directories (in 2 levels) under the output directory of each output format and +# will distribute the generated files over these directories. Enabling this +# option can be useful when feeding doxygen a huge amount of source files, where +# putting all generated files in the same directory would otherwise causes +# performance problems for the file system. +# The default value is: NO. + +CREATE_SUBDIRS = NO + +# If the ALLOW_UNICODE_NAMES tag is set to YES, doxygen will allow non-ASCII +# characters to appear in the names of generated files. If set to NO, non-ASCII +# characters will be escaped, for example _xE3_x81_x84 will be used for Unicode +# U+3044. +# The default value is: NO. + +ALLOW_UNICODE_NAMES = NO + +# The OUTPUT_LANGUAGE tag is used to specify the language in which all +# documentation generated by doxygen is written. Doxygen will use this +# information to generate all constant output in the proper language. +# Possible values are: Afrikaans, Arabic, Armenian, Brazilian, Catalan, Chinese, +# Chinese-Traditional, Croatian, Czech, Danish, Dutch, English (United States), +# Esperanto, Farsi (Persian), Finnish, French, German, Greek, Hungarian, +# Indonesian, Italian, Japanese, Japanese-en (Japanese with English messages), +# Korean, Korean-en (Korean with English messages), Latvian, Lithuanian, +# Macedonian, Norwegian, Persian (Farsi), Polish, Portuguese, Romanian, Russian, +# Serbian, Serbian-Cyrillic, Slovak, Slovene, Spanish, Swedish, Turkish, +# Ukrainian and Vietnamese. +# The default value is: English. + +OUTPUT_LANGUAGE = English + +# If the BRIEF_MEMBER_DESC tag is set to YES, doxygen will include brief member +# descriptions after the members that are listed in the file and class +# documentation (similar to Javadoc). Set to NO to disable this. +# The default value is: YES. + +BRIEF_MEMBER_DESC = YES + +# If the REPEAT_BRIEF tag is set to YES, doxygen will prepend the brief +# description of a member or function before the detailed description +# +# Note: If both HIDE_UNDOC_MEMBERS and BRIEF_MEMBER_DESC are set to NO, the +# brief descriptions will be completely suppressed. +# The default value is: YES. + +REPEAT_BRIEF = YES + +# This tag implements a quasi-intelligent brief description abbreviator that is +# used to form the text in various listings. Each string in this list, if found +# as the leading text of the brief description, will be stripped from the text +# and the result, after processing the whole list, is used as the annotated +# text. Otherwise, the brief description is used as-is. If left blank, the +# following values are used ($name is automatically replaced with the name of +# the entity):The $name class, The $name widget, The $name file, is, provides, +# specifies, contains, represents, a, an and the. + +ABBREVIATE_BRIEF = "The $name class" \ + "The $name widget" \ + "The $name file" \ + is \ + provides \ + specifies \ + contains \ + represents \ + a \ + an \ + the + +# If the ALWAYS_DETAILED_SEC and REPEAT_BRIEF tags are both set to YES then +# doxygen will generate a detailed section even if there is only a brief +# description. +# The default value is: NO. + +ALWAYS_DETAILED_SEC = NO + +# If the INLINE_INHERITED_MEMB tag is set to YES, doxygen will show all +# inherited members of a class in the documentation of that class as if those +# members were ordinary class members. Constructors, destructors and assignment +# operators of the base classes will not be shown. +# The default value is: NO. + +INLINE_INHERITED_MEMB = NO + +# If the FULL_PATH_NAMES tag is set to YES, doxygen will prepend the full path +# before files name in the file list and in the header files. If set to NO the +# shortest path that makes the file name unique will be used +# The default value is: YES. + +FULL_PATH_NAMES = YES + +# The STRIP_FROM_PATH tag can be used to strip a user-defined part of the path. +# Stripping is only done if one of the specified strings matches the left-hand +# part of the path. The tag can be used to show relative paths in the file list. +# If left blank the directory from which doxygen is run is used as the path to +# strip. +# +# Note that you can specify absolute paths here, but also relative paths, which +# will be relative from the directory where doxygen is started. +# This tag requires that the tag FULL_PATH_NAMES is set to YES. + +STRIP_FROM_PATH = + +# The STRIP_FROM_INC_PATH tag can be used to strip a user-defined part of the +# path mentioned in the documentation of a class, which tells the reader which +# header file to include in order to use a class. If left blank only the name of +# the header file containing the class definition is used. Otherwise one should +# specify the list of include paths that are normally passed to the compiler +# using the -I flag. + +STRIP_FROM_INC_PATH = + +# If the SHORT_NAMES tag is set to YES, doxygen will generate much shorter (but +# less readable) file names. This can be useful is your file systems doesn't +# support long names like on DOS, Mac, or CD-ROM. +# The default value is: NO. + +SHORT_NAMES = YES + +# If the JAVADOC_AUTOBRIEF tag is set to YES then doxygen will interpret the +# first line (until the first dot) of a Javadoc-style comment as the brief +# description. If set to NO, the Javadoc-style will behave just like regular Qt- +# style comments (thus requiring an explicit @brief command for a brief +# description.) +# The default value is: NO. + +JAVADOC_AUTOBRIEF = NO + +# If the QT_AUTOBRIEF tag is set to YES then doxygen will interpret the first +# line (until the first dot) of a Qt-style comment as the brief description. If +# set to NO, the Qt-style will behave just like regular Qt-style comments (thus +# requiring an explicit \brief command for a brief description.) +# The default value is: NO. + +QT_AUTOBRIEF = NO + +# The MULTILINE_CPP_IS_BRIEF tag can be set to YES to make doxygen treat a +# multi-line C++ special comment block (i.e. a block of //! or /// comments) as +# a brief description. This used to be the default behavior. The new default is +# to treat a multi-line C++ comment block as a detailed description. Set this +# tag to YES if you prefer the old behavior instead. +# +# Note that setting this tag to YES also means that rational rose comments are +# not recognized any more. +# The default value is: NO. + +MULTILINE_CPP_IS_BRIEF = NO + +# If the INHERIT_DOCS tag is set to YES then an undocumented member inherits the +# documentation from any documented member that it re-implements. +# The default value is: YES. + +INHERIT_DOCS = YES + +# If the SEPARATE_MEMBER_PAGES tag is set to YES then doxygen will produce a new +# page for each member. If set to NO, the documentation of a member will be part +# of the file/class/namespace that contains it. +# The default value is: NO. + +SEPARATE_MEMBER_PAGES = NO + +# The TAB_SIZE tag can be used to set the number of spaces in a tab. Doxygen +# uses this value to replace tabs by spaces in code fragments. +# Minimum value: 1, maximum value: 16, default value: 4. + +TAB_SIZE = 4 + +# This tag can be used to specify a number of aliases that act as commands in +# the documentation. An alias has the form: +# name=value +# For example adding +# "sideeffect=@par Side Effects:\n" +# will allow you to put the command \sideeffect (or @sideeffect) in the +# documentation, which will result in a user-defined paragraph with heading +# "Side Effects:". You can put \n's in the value part of an alias to insert +# newlines. + +ALIASES = + +# This tag can be used to specify a number of word-keyword mappings (TCL only). +# A mapping has the form "name=value". For example adding "class=itcl::class" +# will allow you to use the command class in the itcl::class meaning. + +TCL_SUBST = + +# Set the OPTIMIZE_OUTPUT_FOR_C tag to YES if your project consists of C sources +# only. Doxygen will then generate output that is more tailored for C. For +# instance, some of the names that are used will be different. The list of all +# members will be omitted, etc. +# The default value is: NO. + +OPTIMIZE_OUTPUT_FOR_C = YES + +# Set the OPTIMIZE_OUTPUT_JAVA tag to YES if your project consists of Java or +# Python sources only. Doxygen will then generate output that is more tailored +# for that language. For instance, namespaces will be presented as packages, +# qualified scopes will look different, etc. +# The default value is: NO. + +OPTIMIZE_OUTPUT_JAVA = NO + +# Set the OPTIMIZE_FOR_FORTRAN tag to YES if your project consists of Fortran +# sources. Doxygen will then generate output that is tailored for Fortran. +# The default value is: NO. + +OPTIMIZE_FOR_FORTRAN = NO + +# Set the OPTIMIZE_OUTPUT_VHDL tag to YES if your project consists of VHDL +# sources. Doxygen will then generate output that is tailored for VHDL. +# The default value is: NO. + +OPTIMIZE_OUTPUT_VHDL = NO + +# Doxygen selects the parser to use depending on the extension of the files it +# parses. With this tag you can assign which parser to use for a given +# extension. Doxygen has a built-in mapping, but you can override or extend it +# using this tag. The format is ext=language, where ext is a file extension, and +# language is one of the parsers supported by doxygen: IDL, Java, Javascript, +# C#, C, C++, D, PHP, Objective-C, Python, Fortran (fixed format Fortran: +# FortranFixed, free formatted Fortran: FortranFree, unknown formatted Fortran: +# Fortran. In the later case the parser tries to guess whether the code is fixed +# or free formatted code, this is the default for Fortran type files), VHDL. For +# instance to make doxygen treat .inc files as Fortran files (default is PHP), +# and .f files as C (default is Fortran), use: inc=Fortran f=C. +# +# Note: For files without extension you can use no_extension as a placeholder. +# +# Note that for custom extensions you also need to set FILE_PATTERNS otherwise +# the files are not read by doxygen. + +EXTENSION_MAPPING = + +# If the MARKDOWN_SUPPORT tag is enabled then doxygen pre-processes all comments +# according to the Markdown format, which allows for more readable +# documentation. See http://daringfireball.net/projects/markdown/ for details. +# The output of markdown processing is further processed by doxygen, so you can +# mix doxygen, HTML, and XML commands with Markdown formatting. Disable only in +# case of backward compatibilities issues. +# The default value is: YES. + +MARKDOWN_SUPPORT = NO + +# When enabled doxygen tries to link words that correspond to documented +# classes, or namespaces to their corresponding documentation. Such a link can +# be prevented in individual cases by putting a % sign in front of the word or |