diff options
20 files changed, 2068 insertions, 0 deletions
diff --git a/keyboards/handwired/practice60/boards/GENERIC_STM32_F103/board.c b/keyboards/handwired/practice60/boards/GENERIC_STM32_F103/board.c new file mode 100644 index 0000000000..8c5a87f35f --- /dev/null +++ b/keyboards/handwired/practice60/boards/GENERIC_STM32_F103/board.c @@ -0,0 +1,56 @@ +/* + ChibiOS - Copyright (C) 2006..2015 Giovanni Di Sirio + + Licensed under the Apache License, Version 2.0 (the "License"); + you may not use this file except in compliance with the License. + You may obtain a copy of the License at + + http://www.apache.org/licenses/LICENSE-2.0 + + Unless required by applicable law or agreed to in writing, software + distributed under the License is distributed on an "AS IS" BASIS, + WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. + See the License for the specific language governing permissions and + limitations under the License. +*/ + +#include "hal.h" + +// Value to place in RTC backup register 10 for persistent bootloader mode +#define RTC_BOOTLOADER_FLAG 0x424C + +/** + * @brief PAL setup. + * @details Digital I/O ports static configuration as defined in @p board.h. + * This variable is used by the HAL when initializing the PAL driver. + */ +#if HAL_USE_PAL || defined(__DOXYGEN__) +const PALConfig pal_default_config = +{ + {VAL_GPIOAODR, VAL_GPIOACRL, VAL_GPIOACRH}, + {VAL_GPIOBODR, VAL_GPIOBCRL, VAL_GPIOBCRH}, + {VAL_GPIOCODR, VAL_GPIOCCRL, VAL_GPIOCCRH}, + {VAL_GPIODODR, VAL_GPIODCRL, VAL_GPIODCRH}, + {VAL_GPIOEODR, VAL_GPIOECRL, VAL_GPIOECRH}, +}; +#endif + +/* + * Early initialization code. + * This initialization must be performed just after stack setup and before + * any other initialization. + */ +void __early_init(void) { + + stm32_clock_init(); +} + +/* + * Board-specific initialization code. + */ +void boardInit(void) { + //JTAG-DP Disabled and SW-DP Enabled + AFIO->MAPR |= AFIO_MAPR_SWJ_CFG_JTAGDISABLE; + //Set backup register DR10 to enter bootloader on reset + BKP->DR10 = RTC_BOOTLOADER_FLAG; +} diff --git a/keyboards/handwired/practice60/boards/GENERIC_STM32_F103/board.h b/keyboards/handwired/practice60/boards/GENERIC_STM32_F103/board.h new file mode 100644 index 0000000000..9427adabf1 --- /dev/null +++ b/keyboards/handwired/practice60/boards/GENERIC_STM32_F103/board.h @@ -0,0 +1,166 @@ +/* + ChibiOS - Copyright (C) 2006..2015 Giovanni Di Sirio + + Licensed under the Apache License, Version 2.0 (the "License"); + you may not use this file except in compliance with the License. + You may obtain a copy of the License at + + http://www.apache.org/licenses/LICENSE-2.0 + + Unless required by applicable law or agreed to in writing, software + distributed under the License is distributed on an "AS IS" BASIS, + WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. + See the License for the specific language governing permissions and + limitations under the License. +*/ + +#ifndef _BOARD_H_ +#define _BOARD_H_ + +/* + * Setup for a Generic STM32F103 board. + */ + +/* + * Board identifier. + */ +#define BOARD_GENERIC_STM32_F103 +#define BOARD_NAME "Generic STM32F103x board" + +/* + * Board frequencies. + */ +#define STM32_LSECLK 32768 +#define STM32_HSECLK 8000000 + +/* + * MCU type, supported types are defined in ./os/hal/platforms/hal_lld.h. + */ +#define STM32F103xB + +/* + * IO pins assignments + */ + +/* on-board */ + +#define GPIOA_LED 8 +#define GPIOD_OSC_IN 0 +#define GPIOD_OSC_OUT 1 + +/* In case your board has a "USB enable" hardware + controlled by a pin, define it here. (It could be just + a 1.5k resistor connected to D+ line.) +*/ +/* +#define GPIOB_USB_DISC 10 +*/ + +/* + * I/O ports initial setup, this configuration is established soon after reset + * in the initialization code. + * + * The digits have the following meaning: + * 0 - Analog input. + * 1 - Push Pull output 10MHz. + * 2 - Push Pull output 2MHz. + * 3 - Push Pull output 50MHz. + * 4 - Digital input. + * 5 - Open Drain output 10MHz. + * 6 - Open Drain output 2MHz. + * 7 - Open Drain output 50MHz. + * 8 - Digital input with PullUp or PullDown resistor depending on ODR. + * 9 - Alternate Push Pull output 10MHz. + * A - Alternate Push Pull output 2MHz. + * B - Alternate Push Pull output 50MHz. + * C - Reserved. + * D - Alternate Open Drain output 10MHz. + * E - Alternate Open Drain output 2MHz. + * F - Alternate Open Drain output 50MHz. + * Please refer to the STM32 Reference Manual for details. + */ + +/* + * Port A setup. + * Everything input with pull-up except: + * PA2 - Alternate output (USART2 TX). + * PA3 - Normal input (USART2 RX). + * PA9 - Alternate output (USART1 TX). + * PA10 - Normal input (USART1 RX). + */ +#define VAL_GPIOACRL 0x88884B88 /* PA7...PA0 */ +#define VAL_GPIOACRH 0x888884B8 /* PA15...PA8 */ +#define VAL_GPIOAODR 0xFFFFFFFF + +/* + * Port B setup. + * Everything input with pull-up except: + * PB10 - Push Pull output (USB switch). + */ +#define VAL_GPIOBCRL 0x88888888 /* PB7...PB0 */ +#define VAL_GPIOBCRH 0x88888388 /* PB15...PB8 */ +#define VAL_GPIOBODR 0xFFFFFFFF + +/* + * Port C setup. + * Everything input with pull-up except: + * PC13 - Push Pull output (LED). + */ +#define VAL_GPIOCCRL 0x88888888 /* PC7...PC0 */ +#define VAL_GPIOCCRH 0x88388888 /* PC15...PC8 */ +#define VAL_GPIOCODR 0xFFFFFFFF + +/* + * Port D setup. + * Everything input with pull-up except: + * PD0 - Normal input (XTAL). + * PD1 - Normal input (XTAL). + */ +#define VAL_GPIODCRL 0x88888844 /* PD7...PD0 */ +#define VAL_GPIODCRH 0x88888888 /* PD15...PD8 */ +#define VAL_GPIODODR 0xFFFFFFFF + +/* + * Port E setup. + * Everything input with pull-up except: + */ +#define VAL_GPIOECRL 0x88888888 /* PE7...PE0 */ +#define VAL_GPIOECRH 0x88888888 /* PE15...PE8 */ +#define VAL_GPIOEODR 0xFFFFFFFF + +/* + * USB bus activation macro, required by the USB driver. + */ +/* The point is that most of the generic STM32F103* boards + have a 1.5k resistor connected on one end to the D+ line + and on the other end to some pin. Or even a slightly more + complicated "USB enable" circuit, controlled by a pin. + That should go here. + + However on some boards (e.g. one that I have), there's no + such hardware. In which case it's better to not do anything. +*/ +/* +#define usb_lld_connect_bus(usbp) palClearPad(GPIOB, GPIOB_USB_DISC) +*/ +#define usb_lld_connect_bus(usbp) palSetPadMode(GPIOA, 12, PAL_MODE_INPUT); + +/* + * USB bus de-activation macro, required by the USB driver. + */ +/* +#define usb_lld_disconnect_bus(usbp) palSetPad(GPIOB, GPIOB_USB_DISC) +*/ +#define usb_lld_disconnect_bus(usbp) palSetPadMode(GPIOA, 12, PAL_MODE_OUTPUT_PUSHPULL); palClearPad(GPIOA, 12); + +#if !defined(_FROM_ASM_) +#ifdef __cplusplus +extern "C" { +#endif + void boardInit(void); +#ifdef __cplusplus +} +#endif +#endif /* _FROM_ASM_ */ + +#endif /* _BOARD_H_ */ diff --git a/keyboards/handwired/practice60/boards/GENERIC_STM32_F103/board.mk b/keyboards/handwired/practice60/boards/GENERIC_STM32_F103/board.mk new file mode 100644 index 0000000000..6b8b312fd9 --- /dev/null +++ b/keyboards/handwired/practice60/boards/GENERIC_STM32_F103/board.mk @@ -0,0 +1,5 @@ +# List of all the board related files. +BOARDSRC = $(BOARD_PATH)/boards/GENERIC_STM32_F103/board.c + +# Required include directories +BOARDINC = $(BOARD_PATH)/boards/GENERIC_STM32_F103 diff --git a/keyboards/handwired/practice60/bootloader_defs.h b/keyboards/handwired/practice60/bootloader_defs.h new file mode 100644 index 0000000000..0f45203cb6 --- /dev/null +++ b/keyboards/handwired/practice60/bootloader_defs.h @@ -0,0 +1,10 @@ +/* Address for jumping to bootloader on STM32 chips. */ +/* It is chip dependent, the correct number can be looked up here (page 175): + * http://www.st.com/web/en/resource/technical/document/application_note/CD00167594.pdf + * This also requires a patch to chibios: + * <tmk_dir>/tmk_core/tool/chibios/ch-bootloader-jump.patch + */ + +// STM32F103* does NOT have an USB bootloader in ROM (only serial), +// so setting anything here does not make much sense +// #define STM32_BOOTLOADER_ADDRESS 0x1FFFC800 diff --git a/keyboards/handwired/practice60/chconf.h b/keyboards/handwired/practice60/chconf.h new file mode 100644 index 0000000000..dfb1f9dfb9 --- /dev/null +++ b/keyboards/handwired/practice60/chconf.h @@ -0,0 +1,524 @@ +/* + ChibiOS - Copyright (C) 2006..2015 Giovanni Di Sirio + + Licensed under the Apache License, Version 2.0 (the "License"); + you may not use this file except in compliance with the License. + You may obtain a copy of the License at + + http://www.apache.org/licenses/LICENSE-2.0 + + Unless required by applicable law or agreed to in writing, software + distributed under the License is distributed on an "AS IS" BASIS, + WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. + See the License for the specific language governing permissions and + limitations under the License. +*/ + +/** + * @file templates/chconf.h + * @brief Configuration file template. + * @details A copy of this file must be placed in each project directory, it + * contains the application specific kernel settings. + * + * @addtogroup config + * @details Kernel related settings and hooks. + * @{ + */ + +#ifndef CHCONF_H +#define CHCONF_H + +#define _CHIBIOS_RT_CONF_ + +/*===========================================================================*/ +/** + * @name System timers settings + * @{ + */ +/*===========================================================================*/ + +/** + * @brief System time counter resolution. + * @note Allowed values are 16 or 32 bits. + */ +#define CH_CFG_ST_RESOLUTION 16 + +/** + * @brief System tick frequency. + * @details Frequency of the system timer that drives the system ticks. This + * setting also defines the system tick time unit. + */ +#define CH_CFG_ST_FREQUENCY 2000 + +/** + * @brief Time delta constant for the tick-less mode. + * @note If this value is zero then the system uses the classic + * periodic tick. This value represents the minimum number + * of ticks that is safe to specify in a timeout directive. + * The value one is not valid, timeouts are rounded up to + * this value. + */ +#define CH_CFG_ST_TIMEDELTA 2 + +/** @} */ + +/*===========================================================================*/ +/** + * @name Kernel parameters and options + * @{ + */ +/*===========================================================================*/ + +/** + * @brief Round robin interval. + * @details This constant is the number of system ticks allowed for the + * threads before preemption occurs. Setting this value to zero + * disables the preemption for threads with equal priority and the + * round robin becomes cooperative. Note that higher priority + * threads can still preempt, the kernel is always preemptive. + * @note Disabling the round robin preemption makes the kernel more compact + * and generally faster. + * @note The round robin preemption is not supported in tickless mode and + * must be set to zero in that case. + */ +#define CH_CFG_TIME_QUANTUM 0 + +/** + * @brief Managed RAM size. + * @details Size of the RAM area to be managed by the OS. If set to zero + * then the whole available RAM is used. The core memory is made + * available to the heap allocator and/or can be used directly through + * the simplified core memory allocator. + * + * @note In order to let the OS manage the whole RAM the linker script must + * provide the @p __heap_base__ and @p __heap_end__ symbols. + * @note Requires @p CH_CFG_USE_MEMCORE. + */ +#define CH_CFG_MEMCORE_SIZE 0 + +/** + * @brief Idle thread automatic spawn suppression. + * @details When this option is activated the function @p chSysInit() + * does not spawn the idle thread. The application @p main() + * function becomes the idle thread and must implement an + * infinite loop. + */ +#define CH_CFG_NO_IDLE_THREAD FALSE + +/* Use __WFI in the idle thread for waiting. Does lower the power + * consumption. */ +#define CORTEX_ENABLE_WFI_IDLE TRUE + +/** @} */ + +/*===========================================================================*/ +/** + * @name Performance options + * @{ + */ +/*===========================================================================*/ + +/** + * @brief OS optimization. + * @details If enabled then time efficient rather than space efficient code + * is used when two possible implementations exist. + * + * @note This is not related to the compiler optimization options. + * @note The default is @p TRUE. + */ +#define CH_CFG_OPTIMIZE_SPEED TRUE + +/** @} */ + +/*===========================================================================*/ +/** + * @name Subsystem options + * @{ + */ +/*===========================================================================*/ + +/** + * @brief Time Measurement APIs. + * @details If enabled then the time measurement APIs are included in + * the kernel. + * + * @note The default is @p TRUE. + */ +#define CH_CFG_USE_TM FALSE + +/** + * @brief Threads registry APIs. + * @details If enabled then the registry APIs are included in the kernel. + * + * @note The default is @p TRUE. + */ +#define CH_CFG_USE_REGISTRY TRUE + +/** + * @brief Threads synchronization APIs. + * @details If enabled then the @p chThdWait() function is included in + * the kernel. + * + * @note The default is @p TRUE. + */ +#define CH_CFG_USE_WAITEXIT TRUE + +/** + * @brief Semaphores APIs. + * @details If enabled then the Semaphores APIs are included in the kernel. + * + * @note The default is @p TRUE. + */ +#define CH_CFG_USE_SEMAPHORES TRUE + +/** + * @brief Semaphores queuing mode. + * @details If enabled then the threads are enqueued on semaphores by + * priority rather than in FIFO order. + * + * @note The default is @p FALSE. Enable this if you have special + * requirements. + * @note Requires @p CH_CFG_USE_SEMAPHORES. + */ +#define CH_CFG_USE_SEMAPHORES_PRIORITY FALSE + +/** + * @brief Mutexes APIs. + * @details If enabled then the mutexes APIs are included in the kernel. + * + * @note The default is @p TRUE. + */ +#define CH_CFG_USE_MUTEXES TRUE + +/** + * @brief Enables recursive behavior on mutexes. + * @note Recursive mutexes are heavier and have an increased + * memory footprint. + * + * @note The default is @p FALSE. + * @note Requires @p CH_CFG_USE_MUTEXES. + */ +#define CH_CFG_USE_MUTEXES_RECURSIVE FALSE + +/** + * @brief Conditional Variables APIs. + * @details If enabled then the conditional variables APIs are included + * in the kernel. + * + * @note The default is @p TRUE. + * @note Requires @p CH_CFG_USE_MUTEXES. + */ +#define CH_CFG_USE_CONDVARS TRUE + +/** + * @brief Conditional Variables APIs with timeout. + * @details If enabled then the conditional variables APIs with timeout + * specification are included in the kernel. + * + * @note The default is @p TRUE. + * @note Requires @p CH_CFG_USE_CONDVARS. + */ +#define CH_CFG_USE_CONDVARS_TIMEOUT FALSE + +/** + * @brief Events Flags APIs. + * @details If enabled then the event flags APIs are included in the kernel. + * + * @note The default is @p TRUE. + */ +#define CH_CFG_USE_EVENTS TRUE + +/** + * @brief Events Flags APIs with timeout. + * @details If enabled then the events APIs with timeout specification + * are included in the kernel. + * + * @note The default is @p TRUE. + * @note Requires @p CH_CFG_USE_EVENTS. + */ +#define CH_CFG_USE_EVENTS_TIMEOUT TRUE + +/** + * @brief Synchronous Messages APIs. + * @details If enabled then the synchronous messages APIs are included + * in the kernel. + * + * @note The default is @p TRUE. + */ +#define CH_CFG_USE_MESSAGES TRUE + +/** + * @brief Synchronous Messages queuing mode. + * @details If enabled then messages are served by priority rather than in + * FIFO order. + * + * @note The default is @p FALSE. Enable this if you have special + * requirements. + * @note Requires @p CH_CFG_USE_MESSAGES. + */ +#define CH_CFG_USE_MESSAGES_PRIORITY FALSE + +/** + * @brief Mailboxes APIs. + * @details If enabled then the asynchronous messages (mailboxes) APIs are + * included in the kernel. + * + * @note The default is @p TRUE. + * @note Requires @p CH_CFG_USE_SEMAPHORES. + */ +#define CH_CFG_USE_MAILBOXES TRUE + +/** + * @brief Core Memory Manager APIs. + * @details If enabled then the core memory manager APIs are included + * in the kernel. + * + * @note The default is @p TRUE. + */ +#define CH_CFG_USE_MEMCORE TRUE + +/** + * @brief Heap Allocator APIs. + * @details If enabled then the memory heap allocator APIs are included + * in the kernel. + * + * @note The default is @p TRUE. + * @note Requires @p CH_CFG_USE_MEMCORE and either @p CH_CFG_USE_MUTEXES or + * @p CH_CFG_USE_SEMAPHORES. + * @note Mutexes are recommended. + */ +#define CH_CFG_USE_HEAP TRUE + +/** + * @brief Memory Pools Allocator APIs. + * @details If enabled then the memory pools allocator APIs are included + * in the kernel. + * + * @note The default is @p TRUE. + */ +#define CH_CFG_USE_MEMPOOLS FALSE + +/** + * @brief Dynamic Threads APIs. + * @details If enabled then the dynamic threads creation APIs are included + * in the kernel. + * + * @note The default is @p TRUE. + * @note Requires @p CH_CFG_USE_WAITEXIT. + * @note Requires @p CH_CFG_USE_HEAP and/or @p CH_CFG_USE_MEMPOOLS. + */ +#define CH_CFG_USE_DYNAMIC FALSE + +/** @} */ + +/*===========================================================================*/ +/** + * @name Debug options + * @{ + */ +/*===========================================================================*/ + +/** + * @brief Debug option, kernel statistics. + * + * @note The default is @p FALSE. + */ +#define CH_DBG_STATISTICS FALSE + +/** + * @brief Debug option, system state check. + * @details If enabled the correct call protocol for system APIs is checked + * at runtime. + * + * @note The default is @p FALSE. + */ +#define CH_DBG_SYSTEM_STATE_CHECK FALSE + +/** + * @brief Debug option, parameters checks. + * @details If enabled then the checks on the API functions input + * parameters are activated. + * + * @note The default is @p FALSE. + */ +#define CH_DBG_ENABLE_CHECKS FALSE + +/** + * @brief Debug option, consistency checks. + * @details If enabled then all the assertions in the kernel code are + * activated. This includes consistency checks inside the kernel, + * runtime anomalies and port-defined checks. + * + * @note The default is @p FALSE. + */ +#define CH_DBG_ENABLE_ASSERTS FALSE + +/** + * @brief Debug option, trace buffer. + * @details If enabled then the trace buffer is activated. + * + * @note The default is @p CH_DBG_TRACE_MASK_DISABLED. + */ +#define CH_DBG_TRACE_MASK CH_DBG_TRACE_MASK_DISABLED + +/** + * @brief Trace buffer entries. + * @note The trace buffer is only allocated if @p CH_DBG_TRACE_MASK is + * different from @p CH_DBG_TRACE_MASK_DISABLED. + */ +#define CH_DBG_TRACE_BUFFER_SIZE 128 + +/** + * @brief Debug option, stack checks. + * @details If enabled then a runtime stack check is performed. + * + * @note The default is @p FALSE. + * @note The stack check is performed in a architecture/port dependent way. + * It may not be implemented or some ports. + * @note The default failure mode is to halt the system with the global + * @p panic_msg variable set to @p NULL. + */ +#define CH_DBG_ENABLE_STACK_CHECK FALSE + +/** + * @brief Debug option, stacks initialization. + * @details If enabled then the threads working area is filled with a byte + * value when a thread is created. This can be useful for the + * runtime measurement of the used stack. + * + * @note The default is @p FALSE. + */ +#define CH_DBG_FILL_THREADS FALSE + +/** + * @brief Debug option, threads profiling. + * @details If enabled then a field is added to the @p thread_t structure that + * counts the system ticks occurred while executing the thread. + * + * @note The default is @p FALSE. + * @note This debug option is not currently compatible with the + * tickless mode. + */ +#define CH_DBG_THREADS_PROFILING FALSE + +/** @} */ + +/*===========================================================================*/ +/** + * @name Kernel hooks + * @{ + */ +/*===========================================================================*/ + +/** + * @brief Threads descriptor structure extension. + * @details User fields added to the end of the @p thread_t structure. + */ +#define CH_CFG_THREAD_EXTRA_FIELDS \ + /* Add threads custom fields here.*/ + +/** + * @brief Threads initialization hook. + * @details User initialization code added to the @p chThdInit() API. + * + * @note It is invoked from within @p chThdInit() and implicitly from all + * the threads creation APIs. + */ +#define CH_CFG_THREAD_INIT_HOOK(tp) { \ + /* Add threads initialization code here.*/ \ +} + +/** + * @brief Threads finalization hook. + * @details User finalization code added to the @p chThdExit() API. + */ +#define CH_CFG_THREAD_EXIT_HOOK(tp) { \ + /* Add threads finalization code here.*/ \ +} + +/** + * @brief Context switch hook. + * @details This hook is invoked just before switching between threads. + */ +#define CH_CFG_CONTEXT_SWITCH_HOOK(ntp, otp) { \ + /* Context switch code here.*/ \ +} + +/** + * @brief ISR enter hook. + */ +#define CH_CFG_IRQ_PROLOGUE_HOOK() { \ + /* IRQ prologue code here.*/ \ +} + +/** + * @brief ISR exit hook. + */ +#define CH_CFG_IRQ_EPILOGUE_HOOK() { \ + /* IRQ epilogue code here.*/ \ +} + +/** + * @brief Idle thread enter hook. + * @note This hook is invoked within a critical zone, no OS functions + * should be invoked from here. + * @note This macro can be used to activate a power saving mode. + */ +#define CH_CFG_IDLE_ENTER_HOOK() { \ + /* Idle-enter code here.*/ \ +} + +/** + * @brief Idle thread leave hook. + * @note This hook is invoked within a critical zone, no OS functions + * should be invoked from here. + * @note This macro can be used to deactivate a power saving mode. + */ +#define CH_CFG_IDLE_LEAVE_HOOK() { \ + /* Idle-leave code here.*/ \ +} + +/** + * @brief Idle Loop hook. + * @details This hook is continuously invoked by the idle thread loop. + */ +#define CH_CFG_IDLE_LOOP_HOOK() { \ + /* Idle loop code here.*/ \ +} + +/** + * @brief System tick event hook. + * @details This hook is invoked in the system tick handler immediately + * after processing the virtual timers queue. + */ +#define CH_CFG_SYSTEM_TICK_HOOK() { \ + /* System tick event code here.*/ \ +} + +/** + * @brief System halt hook. + * @details This hook is invoked in case to a system halting error before + * the system is halted. + */ +#define CH_CFG_SYSTEM_HALT_HOOK(reason) { \ + /* System halt code here.*/ \ +} + +/** + * @brief Trace hook. + * @details This hook is invoked each time a new record is written in the + * trace buffer. + */ +#define CH_CFG_TRACE_HOOK(tep) { \ + /* Trace code here.*/ \ +} + +/** @} */ + +/*===========================================================================*/ +/* Port-specific settings (override port settings defaulted in chcore.h). */ +/*===========================================================================*/ + +#endif /* CHCONF_H */ + +/** @} */ diff --git a/keyboards/handwired/practice60/config.h b/keyboards/handwired/practice60/config.h new file mode 100644 index 0000000000..31ddd77d17 --- /dev/null +++ b/keyboards/handwired/practice60/config.h @@ -0,0 +1,74 @@ +/* +Copyright 2015 Jun Wako <wakojun@gmail.com> + +This program is free software: you can redistribute it and/or modify +it under the terms of the GNU General Public License as published by +the Free Software Foundation, either version 2 of the License, or +(at your option) any later version. + +This program is distributed in the hope that it will be useful, +but WITHOUT ANY WARRANTY; without even the implied warranty of +MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +GNU General Public License for more details. + +You should have received a copy of the GNU General Public License +along with this program. If not, see <http://www.gnu.org/licenses/>. +*/ + +#pragma once + +/* USB Device descriptor parameter */ +#define VENDOR_ID 0xFEED +#define PRODUCT_ID 0x6464 +#define DEVICE_VER 0x0001 +/* in python2: list(u"whatever".encode('utf-16-le')) */ +/* at most 32 characters or the ugly hack in usb_main.c borks */ +#define MANUFACTURER QMK +#define PRODUCT Practice 60 +#define DESCRIPTION Practice 60 + +/* key matrix size */ +#define MATRIX_ROWS 5 +#define MATRIX_COLS 14 + +#define MATRIX_COL_PINS { B11, B10, B1, B0, A7, A6, A5, A4, A3, A2, A1, A0, C15, C14 } +#define MATRIX_ROW_PINS { B3, B4, B5, B6, B7 } +#define DIODE_DIRECTION COL2ROW + +#define BACKLIGHT_LEVELS 1 + +/* define if matrix has ghost */ +//#define MATRIX_HAS_GHOST + +/* Set 0 if debouncing isn't needed */ +#define DEBOUNCE 5 + +/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */ +#define LOCKING_SUPPORT_ENABLE +/* Locking resynchronize hack */ +#define LOCKING_RESYNC_ENABLE + +/* key combination for command */ +#define IS_COMMAND() ( \ + keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)) \ +) + + + +/* + * Feature disable options + * These options are also useful to firmware size reduction. + */ + +/* disable debug print */ +//#define NO_DEBUG + +/* disable print */ +//#define NO_PRINT + +/* disable action features */ +//#define NO_ACTION_LAYER +//#define NO_ACTION_TAPPING +//#define NO_ACTION_ONESHOT +//#define NO_ACTION_MACRO +//#define NO_ACTION_FUNCTION diff --git a/keyboards/handwired/practice60/halconf.h b/keyboards/handwired/practice60/halconf.h new file mode 100644 index 0000000000..5fba285a38 --- /dev/null +++ b/keyboards/handwired/practice60/halconf.h @@ -0,0 +1,353 @@ +/* + ChibiOS - Copyright (C) 2006..2015 Giovanni Di Sirio + + Licensed under the Apache License, Version 2.0 (the "License"); + you may not use this file except in compliance with the License. + You may obtain a copy of the License at + + http://www.apache.org/licenses/LICENSE-2.0 + + Unless required by applicable law or agreed to in writing, software + distributed under the License is distributed on an "AS IS" BASIS, + WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. + See the License for the specific language governing permissions and + limitations under the License. +*/ + +/** + * @file templates/halconf.h + * @brief HAL configuration header. + * @details HAL configuration file, this file allows to enable or disable the + * various device drivers from your application. You may also use + * this file in order to override the device drivers default settings. + * + * @addtogroup HAL_CONF + * @{ + */ + +#ifndef _HALCONF_H_ +#define _HALCONF_H_ + +#include "mcuconf.h" + +/** + * @brief Enables the PAL subsystem. + */ +#if !defined(HAL_USE_PAL) || defined(__DOXYGEN__) +#define HAL_USE_PAL TRUE +#endif + +/** + * @brief Enables the ADC subsystem. + */ +#if !defined(HAL_USE_ADC) || defined(__DOXYGEN__) +#define HAL_USE_ADC FALSE +#endif + +/** + * @brief Enables the CAN subsystem. + */ +#if !defined(HAL_USE_CAN) || defined(__DOXYGEN__) +#define HAL_USE_CAN FALSE +#endif + +/** + * @brief Enables the DAC subsystem. + */ +#if !defined(HAL_USE_DAC) || defined(__DOXYGEN__) +#define HAL_USE_DAC FALSE +#endif + +/ |