diff options
107 files changed, 35562 insertions, 41609 deletions
diff --git a/keyboard/Bantam44/Bantam44.c b/keyboard/Bantam44/Bantam44.c new file mode 100644 index 0000000000..ad91401eeb --- /dev/null +++ b/keyboard/Bantam44/Bantam44.c @@ -0,0 +1,25 @@ +#include "Bantam44.h" + +__attribute__ ((weak)) +void matrix_init_user(void) { + // leave these blank +} + +__attribute__ ((weak)) +void matrix_scan_user(void) { + // leave these blank +} + +void matrix_init_kb(void) { + // put your keyboard start-up code here + // runs once when the firmware starts up + + matrix_init_user(); +} + +void matrix_scan_kb(void) { + // put your looping keyboard code here + // runs every cycle (a lot) + + matrix_scan_user(); +}
\ No newline at end of file diff --git a/keyboard/Bantam44/Bantam44.h b/keyboard/Bantam44/Bantam44.h new file mode 100644 index 0000000000..fa5b9df9e4 --- /dev/null +++ b/keyboard/Bantam44/Bantam44.h @@ -0,0 +1,29 @@ +#ifndef BANTAM44_H +#define BANTAM44_H + +#include "matrix.h" +#include "keymap_common.h" +#include "backlight.h" +#include <stddef.h> + +// This a shortcut to help you visually see your layout. +// The following is an example using the Planck MIT layout +// The first section contains all of the arguements +// The second converts the arguments into a two-dimensional array +#define KEYMAP( \ + K00, K01, K02, K03, K04, K05, K06, K07, K08, K09, K0A, K0B, \ + K10, K11, K12, K13, K14, K15, K16, K17, K18, K19, K1A, \ + K20, K21, K22, K23, K24, K25, K26, K27, K28, K29, K2A, K2B, \ + K30, K31, K32, K33, K34, K35, K36, K37, K38 \ +) \ +{ \ + { K00, K01, K02, K03, K04, K05, K06, K07, K08, K09, K0A, K0B }, \ + { K10, K11, K12, K13, K14, K15, K16, K17, K18, K19, KC_NO, K2A }, \ + { K20, K21, K22, K23, K24, K25, K26, K27, K28, K29, K2A, K2B }, \ + { K30, K31, K32, KC_NO, K33, KC_NO, K34, KC_NO, K35, K36, K37, K38 }, \ +} + +void matrix_init_user(void); +void matrix_scan_user(void); + +#endif diff --git a/keyboard/Bantam44/Makefile b/keyboard/Bantam44/Makefile new file mode 100644 index 0000000000..e7dea9f602 --- /dev/null +++ b/keyboard/Bantam44/Makefile @@ -0,0 +1,139 @@ +#---------------------------------------------------------------------------- +# On command line: +# +# make all = Make software. +# +# make clean = Clean out built project files. +# +# make coff = Convert ELF to AVR COFF. +# +# make extcoff = Convert ELF to AVR Extended COFF. +# +# make program = Download the hex file to the device. +# Please customize your programmer settings(PROGRAM_CMD) +# +# make teensy = Download the hex file to the device, using teensy_loader_cli. +# (must have teensy_loader_cli installed). +# +# make dfu = Download the hex file to the device, using dfu-programmer (must +# have dfu-programmer installed). +# +# make flip = Download the hex file to the device, using Atmel FLIP (must +# have Atmel FLIP installed). +# +# make dfu-ee = Download the eeprom file to the device, using dfu-programmer +# (must have dfu-programmer installed). +# +# make flip-ee = Download the eeprom file to the device, using Atmel FLIP +# (must have Atmel FLIP installed). +# +# make debug = Start either simulavr or avarice as specified for debugging, +# with avr-gdb or avr-insight as the front end for debugging. +# +# make filename.s = Just compile filename.c into the assembler code only. +# +# make filename.i = Create a preprocessed source file for use in submitting +# bug reports to the GCC project. +# +# To rebuild project do "make clean" then "make all". +#---------------------------------------------------------------------------- + +# Target file name (without extension). +TARGET = Bantam44 + + +# Directory common source filess exist +TOP_DIR = ../.. +TMK_DIR = ../../tmk_core + +# Directory keyboard dependent files exist +TARGET_DIR = . + +# # project specific files +SRC = Bantam44.c + +ifdef KEYMAP + SRC := keymaps/$(KEYMAP).c $(SRC) +else + SRC := keymaps/default.c $(SRC) +endif + +CONFIG_H = config.h + +# MCU name +#MCU = at90usb1287 +MCU = atmega32u4 + +# Processor frequency. +# This will define a symbol, F_CPU, in all source code files equal to the +# processor frequency in Hz. You can then use this symbol in your source code to +# calculate timings. Do NOT tack on a 'UL' at the end, this will be done +# automatically to create a 32-bit value in your source code. +# +# This will be an integer division of F_USB below, as it is sourced by +# F_USB after it has run through any CPU prescalers. Note that this value +# does not *change* the processor frequency - it should merely be updated to +# reflect the processor speed set externally so that the code can use accurate |