diff options
22 files changed, 1807 insertions, 18 deletions
diff --git a/keyboards/atreus/Makefile b/keyboards/atreus/Makefile index 72b694faac..95ee1d4d7b 100644 --- a/keyboards/atreus/Makefile +++ b/keyboards/atreus/Makefile @@ -5,6 +5,7 @@ ifdef TEENSY2 ATRUES_UPLOAD_COMMAND = teensy_loader_cli -w -mmcu=$(MCU) $(TARGET).hex else OPT_DEFS += -DATREUS_ASTAR + OPT_DEFS += -DCATERINA_BOOTLOADER ATRUES_UPLOAD_COMMAND = while [ ! -r $(USB) ]; do sleep 1; done; \ avrdude -p $(MCU) -c avr109 -U flash:w:$(TARGET).hex -P $(USB) endif diff --git a/keyboards/lets_split/Makefile b/keyboards/lets_split/Makefile new file mode 100644 index 0000000000..b9f07636be --- /dev/null +++ b/keyboards/lets_split/Makefile @@ -0,0 +1,78 @@ +SRC += matrix.c \ + i2c.c \ + split_util.c \ + serial.c + +# MCU name +#MCU = at90usb1287 +MCU = atmega32u4 + +# Processor frequency. +# This will define a symbol, F_CPU, in all source code files equal to the +# processor frequency in Hz. You can then use this symbol in your source code to +# calculate timings. Do NOT tack on a 'UL' at the end, this will be done +# automatically to create a 32-bit value in your source code. +# +# This will be an integer division of F_USB below, as it is sourced by +# F_USB after it has run through any CPU prescalers. Note that this value +# does not *change* the processor frequency - it should merely be updated to +# reflect the processor speed set externally so that the code can use accurate +# software delays. +F_CPU = 16000000 + +# +# LUFA specific +# +# Target architecture (see library "Board Types" documentation). +ARCH = AVR8 + +# Input clock frequency. +# This will define a symbol, F_USB, in all source code files equal to the +# input clock frequency (before any prescaling is performed) in Hz. This value may +# differ from F_CPU if prescaling is used on the latter, and is required as the +# raw input clock is fed directly to the PLL sections of the AVR for high speed +# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' +# at the end, this will be done automatically to create a 32-bit value in your +# source code. +# +# If no clock division is performed on the input clock inside the AVR (via the +# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. +F_USB = $(F_CPU) + +# Interrupt driven control endpoint task(+60) +OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT + + +# Boot Section Size in *bytes* +# Teensy halfKay 512 +# Teensy++ halfKay 1024 +# Atmel DFU loader 4096 +# LUFA bootloader 4096 +# USBaspLoader 2048 +OPT_DEFS += -DBOOTLOADER_SIZE=4096 + +# Build Options +# change to "no" to disable the options, or define them in the Makefile in +# the appropriate keymap folder that will get included automatically +# +BOOTMAGIC_ENABLE ?= no # Virtual DIP switch configuration(+1000) +MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700) +EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) +CONSOLE_ENABLE ?= no # Console for debug(+400) +COMMAND_ENABLE ?= yes # Commands for debug and configuration +NKRO_ENABLE ?= no # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work +BACKLIGHT_ENABLE ?= no # Enable keyboard backlight functionality +MIDI_ENABLE ?= no # MIDI controls +AUDIO_ENABLE ?= yes # Audio output on port C6 +UNICODE_ENABLE ?= no # Unicode +BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID +RGBLIGHT_ENABLE ?= no # Enable WS2812 RGB underlight. Do not enable this with audio at the same time. + +# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE +SLEEP_LED_ENABLE ?= no # Breathing sleep LED during USB suspend + +CUSTOM_MATRIX = yes + +ifndef QUANTUM_DIR + include ../../Makefile +endif
\ No newline at end of file diff --git a/keyboards/lets_split/config.h b/keyboards/lets_split/config.h new file mode 100644 index 0000000000..6f90997ab4 --- /dev/null +++ b/keyboards/lets_split/config.h @@ -0,0 +1,98 @@ +/* +Copyright 2012 Jun Wako <wakojun@gmail.com> + +This program is free software: you can redistribute it and/or modify +it under the terms of the GNU General Public License as published by +the Free Software Foundation, either version 2 of the License, or +(at your option) any later version. + +This program is distributed in the hope that it will be useful, +but WITHOUT ANY WARRANTY; without even the implied warranty of +MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +GNU General Public License for more details. + +You should have received a copy of the GNU General Public License +along with this program. If not, see <http://www.gnu.org/licenses/>. +*/ + +#ifndef CONFIG_H +#define CONFIG_H + +#include "config_common.h" + +/* USB Device descriptor parameter */ +#define VENDOR_ID 0xFEED +#define PRODUCT_ID 0x3060 +#define DEVICE_VER 0x0001 +#define MANUFACTURER Wootpatoot +#define PRODUCT Lets Split +#define DESCRIPTION A split keyboard for the cheap makers + +/* key matrix size */ +// Rows are doubled-up +#define MATRIX_ROWS 8 +#define MATRIX_COLS 6 + +// wiring of each half +#define MATRIX_ROW_PINS { B5, B4, E6, D7 } +#define MATRIX_COL_PINS { F4, F5, F6, F7, B1, B3 } + +#define CATERINA_BOOTLOADER + +// #define USE_I2C + +// #define EE_HANDS + +#define I2C_MASTER_LEFT +// #define I2C_MASTER_RIGHT + +/* COL2ROW or ROW2COL */ +#define DIODE_DIRECTION COL2ROW + +/* define if matrix has ghost */ +//#define MATRIX_HAS_GHOST + +/* number of backlight levels */ +// #define BACKLIGHT_LEVELS 3 + +/* Set 0 if debouncing isn't needed */ +#define DEBOUNCING_DELAY 5 + +/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */ +#define LOCKING_SUPPORT_ENABLE +/* Locking resynchronize hack */ +#define LOCKING_RESYNC_ENABLE + +/* key combination for command */ +#define IS_COMMAND() ( \ + keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)) \ +) + +/* ws2812 RGB LED */ +#define ws2812_PORTREG PORTD +#define ws2812_DDRREG DDRD +#define ws2812_pin PD1 +#define RGBLED_NUM 28 // Number of LEDs +#define RGBLIGHT_HUE_STEP 10 +#define RGBLIGHT_SAT_STEP 17 +#define RGBLIGHT_VAL_STEP 17 + +/* + * Feature disable options + * These options are also useful to firmware size reduction. + */ + +/* disable debug print */ +// #define NO_DEBUG + +/* disable print */ +// #define NO_PRINT + +/* disable action features */ +//#define NO_ACTION_LAYER +//#define NO_ACTION_TAPPING +//#define NO_ACTION_ONESHOT +//#define NO_ACTION_MACRO +//#define NO_ACTION_FUNCTION + +#endif
\ No newline at end of file diff --git a/keyboards/lets_split/eeprom-lefthand.eep b/keyboards/lets_split/eeprom-lefthand.eep new file mode 100644 index 0000000000..a92200b124 --- /dev/null +++ b/keyboards/lets_split/eeprom-lefthand.eep @@ -0,0 +1,2 @@ +:080000000000000000000001F7
+:00000001FF
diff --git a/keyboards/lets_split/eeprom-righthand.eep b/keyboards/lets_split/eeprom-righthand.eep new file mode 100644 index 0000000000..91a6831704 --- /dev/null +++ b/keyboards/lets_split/eeprom-righthand.eep @@ -0,0 +1,2 @@ +:080000000000000000000000F8
+:00000001FF
diff --git a/keyboards/lets_split/i2c.c b/keyboards/lets_split/i2c.c new file mode 100644 index 0000000000..c72789403e --- /dev/null +++ b/keyboards/lets_split/i2c.c @@ -0,0 +1,159 @@ +#include <util/twi.h> +#include <avr/io.h> +#include <stdlib.h> +#include <avr/interrupt.h> +#include <util/twi.h> +#include <stdbool.h> +#include "i2c.h" + +// Limits the amount of we wait for any one i2c transaction. +// Since were running SCL line 100kHz (=> 10μs/bit), and each transactions is +// 9 bits, a single transaction will take around 90μs to complete. +// +// (F_CPU/SCL_CLOCK) => # of μC cycles to transfer a bit +// poll loop takes at least 8 clock cycles to execute +#define I2C_LOOP_TIMEOUT (9+1)*(F_CPU/SCL_CLOCK)/8 + +#define BUFFER_POS_INC() (slave_buffer_pos = (slave_buffer_pos+1)%SLAVE_BUFFER_SIZE) + +volatile uint8_t i2c_slave_buffer[SLAVE_BUFFER_SIZE]; + +static volatile uint8_t slave_buffer_pos; +static volatile bool slave_has_register_set = false; + +// Wait for an i2c operation to finish +inline static +void i2c_delay(void) { + uint16_t lim = 0; + while(!(TWCR & (1<<TWINT)) && lim < I2C_LOOP_TIMEOUT) + lim++; + + // easier way, but will wait slightly longer + // _delay_us(100); +} + +// Setup twi to run at 100kHz +void i2c_master_init(void) { + // no prescaler + TWSR = 0; + // Set TWI clock frequency to SCL_CLOCK. Need TWBR>10. + // Check datasheets for more info. + TWBR = ((F_CPU/SCL_CLOCK)-16)/2; +} + +// Start a transaction with the given i2c slave address. The direction of the +// transfer is set with I2C_READ and I2C_WRITE. +// returns: 0 => success +// 1 => error +uint8_t i2c_master_start(uint8_t address) { + TWCR = (1<<TWINT) | (1<<TWEN) | (1<<TWSTA); + + i2c_delay(); + + // check that we started successfully + if ( (TW_STATUS != TW_START) && (TW_STATUS != TW_REP_START)) + return 1; + + TWDR = address; + TWCR = (1<<TWINT) | (1<<TWEN); + + i2c_delay(); + + if ( (TW_STATUS != TW_MT_SLA_ACK) && (TW_STATUS != TW_MR_SLA_ACK) ) + return 1; // slave did not acknowledge + else + return 0; // success +} + + +// Finish the i2c transaction. +void i2c_master_stop(void) { + TWCR = (1<<TWINT) | (1<<TWEN) | (1<<TWSTO); + + uint16_t lim = 0; + while(!(TWCR & (1<<TWSTO)) && lim < I2C_LOOP_TIMEOUT) + lim++; +} + +// Write one byte to the i2c slave. +// returns 0 => slave ACK +// 1 => slave NACK +uint8_t i2c_master_write(uint8_t data) { + TWDR = data; + TWCR = (1<<TWINT) | (1<<TWEN); + + i2c_delay(); + + // check if the slave acknowledged us + return (TW_STATUS == TW_MT_DATA_ACK) ? 0 : 1; +} + +// Read one byte from the i2c slave. If ack=1 the slave is acknowledged, +// if ack=0 the acknowledge bit is not set. +// returns: byte read from i2c device +uint8_t i2c_master_read(int ack) { + TWCR = (1<<TWINT) | (1<<TWEN) | (ack<<TWEA); + + i2c_delay(); + return TWDR; +} + +void i2c_reset_state(void) { + TWCR = 0; +} + +void i2c_slave_init(uint8_t address) { + TWAR = address << 0; // slave i2c address + // TWEN - twi enable + // TWEA - enable address acknowledgement + // TWINT - twi interrupt flag + // TWIE - enable the twi interrupt + TWCR = (1<<TWIE) | (1<<TWEA) | (1<<TWINT) | (1<<TWEN); +} + +ISR(TWI_vect); + +ISR(TWI_vect) { + uint8_t ack = 1; + switch(TW_STATUS) { + case TW_SR_SLA_ACK: + // this device has been addressed as a slave receiver + slave_has_register_set = false; + break; + + case TW_SR_DATA_ACK: + // this device has received data as a slave receiver + // The first byte that we receive in this transaction sets the location + // of the read/write location of the slaves memory that it exposes over + // i2c. After that, bytes will be written at slave_buffer_pos, incrementing + // slave_buffer_pos after each write. + if(!slave_has_register_set) { + slave_buffer_pos = TWDR; + // don't acknowledge the master if this memory loctaion is out of bounds + if ( slave_buffer_pos >= SLAVE_BUFFER_SIZE ) { + ack = 0; + slave_buffer_pos = 0; + } + slave_has_register_set = true; + } else { + i2c_slave_buffer[slave_buffer_pos] = TWDR; + BUFFER_POS_INC(); + } + break; + + case TW_ST_SLA_ACK: + case TW_ST_DATA_ACK: + // master has addressed this device as a slave transmitter and is + // requesting data. + TWDR = i2c_slave_buffer[slave_buffer_pos]; + BUFFER_POS_INC(); + break; + + case TW_BUS_ERROR: // something went wrong, reset twi state + TWCR = 0; + default: + break; + } + // Reset everything, so we are ready for the next TWI interrupt + TWCR |= (1<<TWIE) | (1<<TWINT) | (ack<<TWEA) | (1<<TWEN); +} diff --git a/keyboards/lets_split/i2c.h b/keyboards/lets_split/i2c.h new file mode 100644 index 0000000000..08ce4b0093 --- /dev/null +++ b/keyboards/lets_split/i2c.h @@ -0,0 +1,31 @@ +#ifndef I2C_H +#define I2C_H + +#include <stdint.h> + +#ifndef F_CPU +#define F_CPU 16000000UL +#endif + +#define I2C_READ 1 +#define I2C_WRITE 0 + +#define I2C_ACK 1 +#define I2C_NACK 0 + +#define SLAVE_BUFFER_SIZE 0x10 + +// i2c SCL clock frequency +#define SCL_CLOCK 100000L + +extern volatile uint8_t i2c_slave_buffer[SLAVE_BUFFER_SIZE]; + +void i2c_master_init(void); +uint8_t i2c_master_start(uint8_t address); +void i2c_master_stop(void); +uint8_t i2c_master_write(uint8_t data); +uint8_t i2c_master_read(int); +void i2c_reset_state(void); +void i2c_slave_init(uint8_t address); + +#endif diff --git a/keyboards/lets_split/imgs/split-keyboard-i2c-schematic.png b/keyboards/lets_split/imgs/split-keyboard-i2c-schematic.png Binary files differnew file mode 100644 index 0000000000..8882947187 --- /dev/null +++ b/keyboards/lets_split/imgs/split-keyboard-i2c-schematic.png diff --git a/keyboards/lets_split/imgs/split-keyboard-serial-schematic.png b/keyboards/lets_split/imgs/split-keyboard-serial-schematic.png Binary files differnew file mode 100644 index 0000000000..7621d38ed9 --- /dev/null +++ b/keyboards/lets_split/imgs/split-keyboard-serial-schematic.png diff --git a/keyboards/lets_split/keymaps/default/keymap.c b/keyboards/lets_split/keymaps/default/keymap.c new file mode 100644 index 0000000000..0d2d94b672 --- /dev/null +++ b/keyboards/lets_split/keymaps/default/keymap.c @@ -0,0 +1,214 @@ +#include "lets_split.h" +#include "action_layer.h" +#include "eeconfig.h" + +extern keymap_config_t keymap_config; + +// Each layer gets a name for readability, which is then used in the keymap matrix below. +// The underscores don't mean anything - you can have a layer called STUFF or any other name. +// Layer names don't all need to be of the same length, obviously, and you can also skip them +// entirely and just use numbers. +#define _QWERTY 0 +#define _COLEMAK 1 +#define _DVORAK 2 +#define _LOWER 3 +#define _RAISE 4 +#define _ADJUST 16 + +enum custom_keycodes { + QWERTY = SAFE_RANGE, + COLEMAK, + DVORAK, + LOWER, + RAISE, + ADJUST, +}; + +// Fillers to make layering more clear +#define _______ KC_TRNS +#define XXXXXXX KC_NO + +const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { + +/* Qwerty + * ,-----------------------------------------------------------------------------------. + * | Tab | Q | W | E | R | T | Y | U | I | O | P | Bksp | + * |------+------+------+------+------+-------------+------+------+------+------+------| + * | Esc | A | S | D | F | G | H | J | K | L | ; | " | + * |------+------+------+------+------+------|------+------+------+------+------+------| + * | Shift| Z | X | C | V | B | N | M | , | . | / |Enter | + * |------+------+------+------+------+------+------+------+------+------+------+------| + * |Adjust| Ctrl | Alt | GUI |Lower |Space |Space |Raise | Left | Down | Up |Right | + * `-----------------------------------------------------------------------------------' + */ +[_QWERTY] = KEYMAP( \ + KC_TAB, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_BSPC, \ + KC_ESC, KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, KC_SCLN, KC_QUOT, \ + KC_LSFT, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_N, KC_M, KC_COMM, KC_DOT, KC_SLSH, KC_ENT , \ + ADJUST, KC_LCTL, KC_LALT, KC_LGUI, LOWER, KC_SPC, KC_SPC, RAISE, KC_LEFT, KC_DOWN, KC_UP, KC_RGHT \ +), + +/* Colemak + * ,-----------------------------------------------------------------------------------. + * | Tab | Q | W | F | P | G | J | L | U | Y | ; | Bksp | + * |------+------+------+------+------+-------------+------+------+------+------+------| + * | Esc | A | R | S | T | D | H | N | E | I | O | " | + * |------+------+------+------+------+------|------+------+------+------+------+------| + * | Shift| Z | X | C | V | B | K | M | , | . | / |Enter | + * |------+------+------+------+------+------+------+------+------+------+------+------| + * |Adjust| Ctrl | Alt | GUI |Lower |Space |Space |Raise | Left | Down | Up |Right | + * `-----------------------------------------------------------------------------------' + */ +[_COLEMAK] = KEYMAP( \ + KC_TAB, KC_Q, KC_W, KC_F, KC_P, KC_G, KC_J, KC_L, KC_U, KC_Y, KC_SCLN, KC_BSPC, \ + KC_ESC, KC_A, KC_R, KC_S, KC_T, KC_D, KC_H, KC_N, KC_E, KC_I, KC_O, KC_QUOT, \ + KC_LSFT, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_K, KC_M, KC_COMM, KC_DOT, KC_SLSH, KC_ENT , \ + ADJUST, KC_LCTL, KC_LALT, KC_LGUI, LOWER, KC_SPC, KC_SPC, RAISE, KC_LEFT, KC_DOWN, KC_UP, KC_RGHT \ +), + +/* Dvorak + * ,-----------------------------------------------------------------------------------. + * | Tab | " | , | . | P | Y | F | G | C | R | L | Bksp | + * |------+------+------+------+------+-------------+------+------+------+------+------| + * | Esc | A | O | E | U | I | D | H | T | N | S | / | + * |------+------+------+------+------+------|------+------+------+------+------+------| + * | Shift| ; | Q | J | K | X | B | M | W | V | Z |Enter | + * |------+------+------+------+------+------+------+------+------+------+------+------| + * |Adjust| Ctrl | Alt | GUI |Lower |Space |Space |Raise | Left | Down | Up |Right | + * `-----------------------------------------------------------------------------------' + */ +[_DVORAK] = KEYMAP( \ + KC_TAB, KC_QUOT, KC_COMM, KC_DOT, KC_P, KC_Y, KC_F, KC_G, KC_C, KC_R, KC_L, KC_BSPC, \ + KC_ESC, KC_A, KC_O, KC_E, KC_U, KC_I, KC_D, KC_H, KC_T, KC_N, KC_S, KC_SLSH, \ + KC_LSFT, KC_SCLN, KC_Q, KC_J, KC_K, KC_X, KC_B, KC_M, KC_W, KC_V, KC_Z, KC_ENT , \ + ADJUST, KC_LCTL, KC_LALT, KC_LGUI, LOWER, KC_SPC, KC_SPC, RAISE, KC_LEFT, KC_DOWN, KC_UP, KC_RGHT \ +), + +/* Lower + * ,-----------------------------------------------------------------------------------. + * | ~ | ! | @ | # | $ | % | ^ | & | * | ( | ) | Bksp | + * |------+------+------+------+------+-------------+------+------+------+------+------| + * | Del | F1 | F2 | F3 | F4 | F5 | F6 | _ | + | | \ | | | + * |------+------+------+------+------+------|------+------+------+------+------+------| + * | | F7 | F8 | F9 | F10 | F11 | F12 |ISO ~ |ISO | | | |Enter | + * |------+------+------+------+------+------+------+------+------+------+------+------| + * | | | | | | | | Next | Vol- | Vol+ | Play | + * `-----------------------------------------------------------------------------------' + */ +[_LOWER] = KEYMAP( \ + KC_TILD, KC_EXLM, KC_AT, KC_HASH, KC_DLR, KC_PERC, KC_CIRC, KC_AMPR, KC_ASTR, KC_LPRN, KC_RPRN, KC_BSPC, \ + KC_DEL, KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_UNDS, KC_PLUS, KC_LCBR, KC_RCBR, KC_PIPE, \ + _______, KC_F7, KC_F8, KC_F9, KC_F10, KC_F11, KC_F12,S(KC_NUHS),S(KC_NUBS),_______, _______, _______, \ + _______, _______, _______, _______, _______, _______, _______, _______, KC_MNXT, KC_VOLD, KC_VOLU, KC_MPLY \ +), + +/* Raise + * ,-----------------------------------------------------------------------------------. + * | ` | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 0 | Bksp | + * |------+------+------+------+------+-------------+------+------+------+------+------| + * | Del | F1 | F2 | F3 | F4 | F5 | F6 | - | = | [ | ] | \ | + * |------+------+------+------+------+------|------+------+------+------+------+------| + * | | F7 | F8 | F9 | F10 | F11 | F12 |ISO # |ISO / | | |Enter | + * |------+------+------+------+------+------+------+------+------+------+------+------| + * | | | | | | | | Next | Vol- | Vol+ | Play | + * `-----------------------------------------------------------------------------------' + */ +[_RAISE] = KEYMAP( \ + KC_GRV, KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_BSPC, \ + KC_DEL, KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_MINS, KC_EQL, KC_LBRC, KC_RBRC, KC_BSLS, \ + _______, KC_F7, KC_F8, KC_F9, KC_F10, KC_F11, KC_F12, KC_NUHS, KC_NUBS, _______, _______, _______, \ + _______, _______, _______, _______, _______, _______, _______, _______, KC_MNXT, KC_VOLD, KC_VOLU, KC_MPLY \ +), + +/* Adjust (Lower + Raise) + * ,-----------------------------------------------------------------------------------. + * | | Reset| | | | | | | | | | Del | + * |------+------+------+------+------+-------------+------+------+------+------+------| + * | | | |Aud on|Audoff|AGnorm|AGswap|Qwerty|Colemk|Dvorak| | | + * |------+------+------+------+------+------|------+------+------+------+------+------| + * | | | | | | | | | | | | | + * |------+------+------+------+------+------+------+------+------+------+------+------| + * | | | | | | | | | | | | + * `-----------------------------------------------------------------------------------' + */ +[_ADJUST] = KEYMAP( \ + _______, RESET, _______, _______, _______, _______, _______, _______, _______, _______, _______, KC_DEL, \ + _______, _______, _______, AU_ON, AU_OFF, AG_NORM, AG_SWAP, QWERTY, COLEMAK, DVORAK, _______, _______, \ + _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, \ + _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______ \ +) + + +}; + +#ifdef AUDIO_ENABLE +float tone_qwerty[][2] = SONG(QWERTY_SOUND); +float tone_dvorak[][2] = SONG(DVORAK_SOUND); +float tone_colemak[][2] = SONG(COLEMAK_SOUND); +#endif + +void persistant_default_layer_set(uint16_t default_layer) { + eeconfig_update_default_layer(default_layer); + default_layer_set(default_layer); +} + +bool process_record_user(uint16_t keycode, keyrecord_t *record) { + switch (keycode) { + case QWERTY: + if (record->event.pressed) { + #ifdef AUDIO_ENABLE + PLAY_NOTE_ARRAY(tone_qwerty, false, 0); + #endif + persistant_default_layer_set(1UL<<_QWERTY); + } + return false; + break; + case COLEMAK: + if (record->event.pressed) { + #ifdef AUDIO_ENABLE + PLAY_NOTE_ARRAY(tone_colemak, false, 0); + #endif + persistant_default_layer_set(1UL<<_COLEMAK); + } + return false; + break; + case DVORAK: + if (record->event.pressed) { + #ifdef AUDIO_ENABLE + PLAY_NOTE_ARRAY(tone_dvorak, false, 0); + #endif + persistant_default_layer_set(1UL<<_DVORAK); + } + return false; + break; + case LOWER: + if (record->event.pressed) { + layer_on(_LOWER); + update_tri_layer(_LOWER, _RAISE, _ADJUST); + } else { + layer_off(_LOWER); + update_tri_layer(_LOWER, _RAISE, _ADJUST); + } + return false; + break; + case RAISE: + if (record->event.pressed) { + layer_on(_RAISE); + update_tri_layer(_LOWER, _RAISE, _ADJUST); + } else { + layer_off(_RAISE); + update_tri_layer(_LOWER, _RAISE, _ADJUST); + } + return false; + break; + case ADJUST: + if (record->event.pressed) { + layer_on(_ADJUST); + } else { + layer_off(_ADJUST); + } + return false; + break; + } + return true; +}
\ No newline at end of file diff --git a/keyboards/lets_split/lets_split.c b/keyboards/lets_split/lets_split.c new file mode 100644 index 0000000000..574c116a75 --- /dev/null +++ b/keyboards/lets_split/lets_split.c @@ -0,0 +1,30 @@ +#include "lets_split.h" + +#ifdef AUDIO_ENABLE + float tone_startup[][2] = SONG(STARTUP_SOUND); + float tone_goodbye[][2] = SONG(GOODBYE_SOUND); +#endif + +void matrix_init_kb(void) { + + #ifdef AUDIO_ENABLE + _delay_ms(20); // gets rid of tick + PLAY_NOTE_ARRAY(tone_startup, false, 0); + #endif + + // // green led on + // DDRD |= (1<<5); + // PORTD &= ~(1<<5); + + // // orange led on + // DDRB |= (1<<0); + // PORTB &= ~(1<<0); + + matrix_init_user(); +}; + +void shutdown_user(void) { + PLAY_NOTE_ARRAY(tone_goodbye, false, 0); + _delay_ms(150); + stop_all_notes(); +} diff --git a/keyboards/lets_split/lets_split.h b/keyboards/lets_split/lets_split.h new file mode 100644 index 0000000000..fe7ae07679 --- /dev/null +++ b/keyboards/lets_split/lets_split.h @@ -0,0 +1,25 @@ +#ifndef LETS_SPLIT_H +#define LETS_SPLIT_H + +#include "quantum.h" + +void promicro_bootloader_jmp(bool program); + +#define KEYMAP( \ + k00, k01, k02, k03, k04, k05, k40, k41, k42, k43, k44, k45, \ + k10, k11, k12, k13, k14, k15, k50, k51, k52, k53, k54, k55, \ + k20, k21, k22, k23, k24, k25, k60, k61, k62, k63, k64, k65, \ + k30, k31, k32, k33, k34, k35, k70, k71, k72, k73, k74, k75 \ + ) \ + { \ + { k00, k01, k02, k03, k04, k05 }, \ + { k10, k11, k12, k13, k14, k15 }, \ + { k20, k21, k22, k23, k24, k25 }, \ + { k30, k31, k32, k33, k34, k35 }, \ + { k40, k41, k42, k43, k44, k45 }, \ + { k50, k51, k52, k53, k54, k55 }, \ + { k60, k61, k62, k63, k64, k65 }, \ + { k70, k71, k72, k73, k74, k75 } \ + } + +#endif
\ No newline at end of file diff --git a/keyboards/lets_split/matrix.c b/keyboards/lets_split/matrix.c new file mode 100644 index 0000000000..1d768c59b3 --- /dev/null +++ b/keyboards/lets_split/matrix.c @@ -0,0 +1,311 @@ +/* +Copyright 2012 Jun Wako <wakojun@gmail.com> + +This program is free software: you can redistribute it and/or modify +it under the terms of the GNU General Public License as published by +the Free Software Foundation, either version 2 of the License, or +(at your option) any later version. + +This program is distributed in the hope that it will be useful, +but WITHOUT ANY WARRANTY; without even the implied warranty of +MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +GNU General Public License for more details. + +You should have received a copy of the GNU General Public License +along with this program. If not, see <http://www.gnu.org/licenses/>. +*/ + +/* + * scan matrix + */ +#include <stdint.h> +#include <stdbool.h> +#include <avr/io.h> +#include <avr/wdt.h> +#include <avr/interrupt.h> +#include <util/delay.h> +#include "print.h" +#include "debug.h" +#include "util.h" +#include "matrix.h" +#include "i2c.h" +#include "serial.h" +#include "split_util.h" +#include "pro_micro.h" +#include "config.h" + +#ifndef DEBOUNCE +# define DEBOUNCE 5 +#endif + +#define ERROR_DISCONNECT_COUNT 5 + +static uint8_t debouncing = DEBOUNCE; +static const int ROWS_PER_HAND = MATRIX_ROWS/2; +static uint8_t error_count = 0; + +static const uint8_t row_pins[MATRIX_ROWS] = MATRIX_ROW_PINS; +static const uint8_t col_pins[MATRIX_COLS] = MATRIX_COL_PINS; + +/* matrix state(1:on, 0:off) */ +static matrix_row_t matrix[MATRIX_ROWS]; +static matrix_row_t matrix_debouncing[MATRIX_ROWS]; + +static matrix_row_t read_cols(void); +static void init_cols(void); +static void unselect_rows(void); +static void select_row(uint8_t row); + +__attribute__ ((weak)) +void matrix_init_quantum(void) { + matrix_init_kb(); +} + +__attribute__ ((weak)) +void matrix_scan_quantum(void) { + matrix_scan_kb(); +} + +__attribute__ ((weak)) +void matrix_init_kb(void) { + matrix_init_user(); +} + +__attribute__ ((weak)) +void matrix_scan_kb(void) { + matrix_scan_user(); +} + +__attribute__ ((weak)) +void matrix_init_user(void) { +} + +__attribute__ ((weak)) +void matrix_scan_user(void) { +} + +inline +uint8_t matrix_rows(void) +{ + return MATRIX_ROWS; +} + +inline +uint8_t matrix_cols(void) +{ + return MATRIX_COLS; +} + +void matrix_init(void) +{ + debug_enable = true; + debug_matrix = true; + debug_mouse = true; + // initialize row and col + unselect_rows(); + init_cols(); + + TX_RX_LED_INIT; + + // initialize matrix state: all keys off + for (uint8_t i=0; i < MATRIX_ROWS; i++) { + matrix[i] = 0; + matrix_debouncing[i] = 0; + } + + matrix_init_quantum(); +} + +uint8_t _matrix_scan(void) +{ + // Right hand is stored after the left in the matirx so, we need to offset it + int offset = isLeftHand ? 0 : (ROWS_PER_HAND); + + for (uint8_t i = 0; i < ROWS_PER_HAND; i++) { + select_row(i); + _delay_us(30); // without this wait read unstable value. + matrix_row_t cols = read_cols(); + if (matrix_debouncing[i+offset] != cols) { + matrix_debouncing[i+offset] = cols; + debouncing = DEBOUNCE; + } + unselect_rows(); + } + + if (debouncing) { + if (--debouncing) { + _delay_ms(1); + } else { + for (uint8_t i = 0; i < ROWS_PER_HAND; i++) { + matrix[i+offset] = matrix_debouncing[i+offset]; + } + } + } + + return 1; +} + +// Get rows from other half over i2c +int i2c_transaction(void) { + int slaveOffset = (isLeftHand) ? (ROWS_PER_HAND) : 0; + + int err = i2c_master_start(SLAVE_I2C_ADDRESS + I2C_WRITE); + if (err) goto i2c_error; + + // start of matrix stored at 0x00 + err = i2c_master_write(0x00); + if (err) goto i2c_error; + + // Start read + err = i2c_master_start(SLAVE_I2C_ADDRESS + I2C_READ); + if (err) goto i2c_error; + + if (!err) { + int i; + for (i = 0; i < ROWS_PER_HAND-1; ++i) { + matrix[slaveOffset+i] = i2c_master_read(I2C_ACK); + } + matrix[slaveOffset+i] = i2c_master_read(I2C_NAC |
