diff options
| -rw-r--r-- | keyboards/clueboard2/Makefile | 71 | ||||
| -rw-r--r-- | keyboards/clueboard2/clueboard2.c | 63 |
2 files changed, 0 insertions, 134 deletions
diff --git a/keyboards/clueboard2/Makefile b/keyboards/clueboard2/Makefile deleted file mode 100644 index e9367a90d0..0000000000 --- a/keyboards/clueboard2/Makefile +++ /dev/null @@ -1,71 +0,0 @@ - - -# MCU name -#MCU = at90usb1287 -MCU = atmega32u4 - -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - -# Boot Section Size in *bytes* -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 -OPT_DEFS += -DBOOTLOADER_SIZE=4096 - - -# Build Options -# comment out to disable the options. -# -BOOTMAGIC_ENABLE ?= yes # Virtual DIP switch configuration(+1000) -MOUSEKEY_ENABLE ?= no # Mouse keys(+4700) -EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) -CONSOLE_ENABLE ?= yes # Console for debug(+400) -COMMAND_ENABLE ?= yes # Commands for debug and configuration -NKRO_ENABLE ?= yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work -RGBLIGHT_ENABLE ?= no # Enable keyboard underlight functionality (+4870) -BACKLIGHT_ENABLE ?= yes # Enable keyboard backlight functionality (+1150) -MIDI_ENABLE ?= no # MIDI controls -AUDIO_ENABLE ?= no -UNICODE_ENABLE ?= no # Unicode -BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID - -ifndef QUANTUM_DIR - include ../../Makefile -endif diff --git a/keyboards/clueboard2/clueboard2.c b/keyboards/clueboard2/clueboard2.c deleted file mode 100644 index d78ffed9ba..0000000000 --- a/keyboards/clueboard2/clueboard2.c +++ /dev/null @@ -1,63 +0,0 @@ -#include "clueboard2.h" - -void matrix_init_kb(void) { - // put your keyboard start-up code here - // runs once when the firmware starts up - matrix_init_user(); - led_init_ports(); - - // JTAG disable for PORT F. write JTD bit twice within four cycles. - MCUCR |= (1<<JTD); - MCUCR |= (1<<JTD); -}; - -void led_init_ports() { - // * Set our LED pins as output - DDRB |= (1<<4); -} - -void led_set_kb(uint8_t usb_led) { - if (usb_led & (1<<USB_LED_CAPS_LOCK)) { - // Turn capslock on - PORTB |= (1<<4); - } else { - // Turn capslock off - PORTB &= ~(1<<4); - } -} - -/* Clueboard 2.0 LED locations: - * - * Capslock: B4, pull high to turn on - * LCtrl: Shared with Capslock, DO NOT INSTALL LED'S IN BOTH - * Page Up: B7, pull high to turn on - * Escape: D6, pull high to turn on - * Arrows: D4, pull high to turn on - */ - -void backlight_init_ports(void) { - print("init_backlight_pin()\n"); - // Set our LED pins as output - DDRD |= (1<<6); // Esc - DDRB |= (1<<7); // Page Up - DDRD |= (1<<4); // Arrows - - // Set our LED pins low - PORTD &= ~(1<<6); // Esc - PORTB &= ~(1<<7); // Page Up - PORTD &= ~(1<<4); // Arrows -} - -void backlight_set(uint8_t level) { - if ( level == 0 ) { - // Turn off light - PORTD |= (1<<6); // Esc - PORTB |= (1<<7); // Page Up - PORTD |= (1<<4); // Arrows - } else { - // Turn on light - PORTD &= ~(1<<6); // Esc - PORTB &= ~(1<<7); // Page Up - PORTD &= ~(1<<4); // Arrows - } -} |