Merge remote-tracking branch 'upstream/master'

4 files changed, 15 insertions, 54 deletions

diff --git a/keyboards/handwired/hnah40/config.h b/keyboards/handwired/hnah40/config.h
index b7a4105d00..3d3c05fd42 100644
--- a/keyboards/handwired/hnah40/config.h
+++ b/keyboards/handwired/hnah40/config.h
@@ -78,6 +78,8 @@ along with this program.  If not, see <http://www.gnu.org/licenses/>.
  */
 // #define GRAVE_ESC_CTRL_OVERRIDE
 
+#define USB_MAX_POWER_CONSUMPTION 100
+
 /*
  * Force NKRO
  *
diff --git a/keyboards/handwired/hnah40/info.json b/keyboards/handwired/hnah40/info.json
index 6a577a5207..f9664d22c9 100644
--- a/keyboards/handwired/hnah40/info.json
+++ b/keyboards/handwired/hnah40/info.json
@@ -39,7 +39,8 @@
                 {"label":"N", "x":6.75, "y":2}, 
                 {"label":"M", "x":7.75, "y":2}, 
                 {"label":",", "x":8.75, "y":2}, 
-                {"label":"Shift", "x":9.75, "y":2, "w":2.25}, 
+                {"label":".", "x":9.75, "y":2}, 
+                {"label":"Shift", "x":10.75, "y":2, "w":1.25}, 
                 {"label":"Ctrl", "x":0, "y":3, "w":1.25}, 
                 {"label":"Win", "x":1.25, "y":3, "w":1.5}, 
                 {"label":"Alt", "x":2.75, "y":3, "w":1.25}, 
@@ -51,4 +52,4 @@
             ]
         }
     }
-}
\ No newline at end of file
+}
diff --git a/keyboards/handwired/hnah40/rules.mk b/keyboards/handwired/hnah40/rules.mk
index efd11bfa5c..bbdf5176c4 100644
--- a/keyboards/handwired/hnah40/rules.mk
+++ b/keyboards/handwired/hnah40/rules.mk
@@ -1,44 +1,15 @@
 # MCU name
 MCU = atmega328p
-PROTOCOL = VUSB
 
-# Processor frequency.
-#     This will define a symbol, F_CPU, in all source code files equal to the
-#     processor frequency in Hz. You can then use this symbol in your source code to
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-#     automatically to create a 32-bit value in your source code.
-#
-#     This will be an integer division of F_USB below, as it is sourced by
-#     F_USB after it has run through any CPU prescalers. Note that this value
-#     does not *change* the processor frequency - it should merely be updated to
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-BOOTLOADER = bootloadHID
+# Bootloader selection
+#   Teensy       halfkay
+#   Pro Micro    caterina
+#   Atmel DFU    atmel-dfu
+#   LUFA DFU     lufa-dfu
+#   QMK DFU      qmk-dfu
+#   ATmega32A    bootloadHID
+#   ATmega328P   USBasp
+BOOTLOADER = USBasp
 
 # Flash program via avrdude, but default command is not suitable.
 # You can use hnah40:default:program
@@ -69,5 +40,3 @@ BLUETOOTH_ENABLE = no       # Enable Bluetooth with the Adafruit EZ-Key HID
 AUDIO_ENABLE = no           # Audio output on port C6
 FAUXCLICKY_ENABLE = no      # Use buzzer to emulate clicky switches
 HD44780_ENABLE = no 		# Enable support for HD44780 based LCDs (+400)
-NO_UART = yes
-NO_SUSPEND_POWER_DOWN = yes
\ No newline at end of file
diff --git a/keyboards/handwired/hnah40/usbconfig.h b/keyboards/handwired/hnah40/usbconfig.h
index cbd37c34dc..b26a3c7d67 100644
--- a/keyboards/handwired/hnah40/usbconfig.h
+++ b/keyboards/handwired/hnah40/usbconfig.h
@@ -109,21 +109,10 @@ section at the end of this file).
  * (e.g. HID), but never want to send any data. This option saves a couple
  * of bytes in flash memory and the transmit buffers in RAM.
  */
-#define USB_CFG_INTR_POLL_INTERVAL      1
-/* If you compile a version with endpoint 1 (interrupt-in), this is the poll
- * interval. The value is in milliseconds and must not be less than 10 ms for
- * low speed devices.
- */
 #define USB_CFG_IS_SELF_POWERED         0
 /* Define this to 1 if the device has its own power supply. Set it to 0 if the
  * device is powered from the USB bus.
  */
-// max power draw with maxed white underglow measured at 120 mA (peaks)
-#define USB_CFG_MAX_BUS_POWER           100
-/* Set this variable to the maximum USB bus power consumption of your device.
- * The value is in milliamperes. [It will be divided by two since USB
- * communicates power requirements in units of 2 mA.]
- */
 #define USB_CFG_IMPLEMENT_FN_WRITE      1
 /* Set this to 1 if you want usbFunctionWrite() to be called for control-out
  * transfers. Set it to 0 if you don't need it and want to save a couple of
@@ -239,7 +228,7 @@ section at the end of this file).
  * with libusb: 0x16c0/0x5dc.  Use this VID/PID pair ONLY if you understand
  * the implications!
  */
-#define USB_CFG_DEVICE_VERSION  0x00, 0x01
+#define USB_CFG_DEVICE_VERSION  (DEVICE_VER & 0xFF), ((DEVICE_VER >> 8) & 0xFF)
 /* Version number of the device: Minor number first, then major number.
  */
 #define USB_CFG_VENDOR_NAME     'H','n','a','h','K','B'