Merge branch 'master' into coderkun_neo2

9 files changed, 710 insertions, 713 deletions

diff --git a/keyboards/gh60/Makefile b/keyboards/gh60/Makefile
index 39a9cc0ae1..57b2ef62e5 100644
--- a/keyboards/gh60/Makefile
+++ b/keyboards/gh60/Makefile
@@ -1,74 +1,3 @@
-

-

-# MCU name

-#MCU = at90usb1287

-MCU = atmega32u4

-

-# Processor frequency.

-#     This will define a symbol, F_CPU, in all source code files equal to the

-#     processor frequency in Hz. You can then use this symbol in your source code to

-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done

-#     automatically to create a 32-bit value in your source code.

-#

-#     This will be an integer division of F_USB below, as it is sourced by

-#     F_USB after it has run through any CPU prescalers. Note that this value

-#     does not *change* the processor frequency - it should merely be updated to

-#     reflect the processor speed set externally so that the code can use accurate

-#     software delays.

-F_CPU = 16000000

-

-

-#

-# LUFA specific

-#

-# Target architecture (see library "Board Types" documentation).

-ARCH = AVR8

-

-# Input clock frequency.

-#     This will define a symbol, F_USB, in all source code files equal to the

-#     input clock frequency (before any prescaling is performed) in Hz. This value may

-#     differ from F_CPU if prescaling is used on the latter, and is required as the

-#     raw input clock is fed directly to the PLL sections of the AVR for high speed

-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'

-#     at the end, this will be done automatically to create a 32-bit value in your

-#     source code.

-#

-#     If no clock division is performed on the input clock inside the AVR (via the

-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.

-F_USB = $(F_CPU)

-

-# Interrupt driven control endpoint task(+60)

-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT

-

-

-# Boot Section Size in *bytes*

-#   Teensy halfKay   512

-#   Teensy++ halfKay 1024

-#   Atmel DFU loader 4096

-#   LUFA bootloader  4096

-#   USBaspLoader     2048

-OPT_DEFS += -DBOOTLOADER_SIZE=4096

-

-

-# Build Options

-#   comment out to disable the options.

-#

-BOOTMAGIC_ENABLE ?= yes		# Virtual DIP switch configuration(+1000)

-MOUSEKEY_ENABLE ?= yes		# Mouse keys(+4700)

-EXTRAKEY_ENABLE ?= yes		# Audio control and System control(+450)

-# CONSOLE_ENABLE ?= yes		# Console for debug(+400)

-# COMMAND_ENABLE ?= yes		# Commands for debug and configuration

-KEYBOARD_LOCK_ENABLE ?= yes	# Allow locking of keyboard via magic key

-# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE

-# SLEEP_LED_ENABLE ?= yes	# Breathing sleep LED during USB suspend

-NKRO_ENABLE ?= yes			# USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work

-# BACKLIGHT_ENABLE ?= yes	# Enable keyboard backlight functionality

-# MIDI_ENABLE ?= YES			# MIDI controls

-# UNICODE_ENABLE ?= YES		# Unicode

-# BLUETOOTH_ENABLE ?= yes	# Enable Bluetooth with the Adafruit EZ-Key HID

-

-

-ifndef QUANTUM_DIR

-	include ../../Makefile

-endif

-

+ifndef MAKEFILE_INCLUDED
+	include ../../Makefile
+endif
diff --git a/keyboards/gh60/config.h b/keyboards/gh60/config.h
index 4813c4e786..97753bc069 100644
--- a/keyboards/gh60/config.h
+++ b/keyboards/gh60/config.h
@@ -1,161 +1,161 @@
-/*

-Copyright 2012 Jun Wako <wakojun@gmail.com>

-

-This program is free software: you can redistribute it and/or modify

-it under the terms of the GNU General Public License as published by

-the Free Software Foundation, either version 2 of the License, or

-(at your option) any later version.

-

-This program is distributed in the hope that it will be useful,

-but WITHOUT ANY WARRANTY; without even the implied warranty of

-MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the

-GNU General Public License for more details.

-

-You should have received a copy of the GNU General Public License

-along with this program. If not, see <http://www.gnu.org/licenses/>.

-*/

-

-#ifndef CONFIG_H

-#define CONFIG_H

-

-#include "config_common.h"

-

-/* USB Device descriptor parameter */

-#define VENDOR_ID    0xFEED

-#define PRODUCT_ID   0x6060

-#define DEVICE_VER   0x0001

-#define MANUFACTURER    geekhack

-#define PRODUCT         GH60

-#define DESCRIPTION     t.m.k. keyboard firmware for GH60

-

-/* key matrix size */

-#define MATRIX_ROWS 5

-#define MATRIX_COLS 14

-

-/*

- * Keyboard Matrix Assignments

- *

- * Change this to how you wired your keyboard

- * COLS: AVR pins used for columns, left to right

- * ROWS: AVR pins used for rows, top to bottom

- * DIODE_DIRECTION: COL2ROW = COL = Anode (+), ROW = Cathode (-, marked on diode)

- *         ROW2COL = ROW = Anode (+), COL = Cathode (-, marked on diode)

- *

-*/

- #define MATRIX_ROW_PINS { D0, D1, D2, D3, D5 }

-// Rev A

-// #define MATRIX_COL_PINS { F0, F1, E6, C7, C6, B6, D4, B1, B0, B5, B4, D7, D6, B3 }

-// Rev B/C

-   #define MATRIX_COL_PINS { F0, F1, E6, C7, C6, B6, D4, B1, B7, B5, B4, D7, D6, B3 }

-#define UNUSED_PINS

-

-/* COL2ROW or ROW2COL */

-#define DIODE_DIRECTION COL2ROW

-

-/* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */

-#define DEBOUNCING_DELAY 5

-

-/* define if matrix has ghost (lacks anti-ghosting diodes) */

-//#define MATRIX_HAS_GHOST

-

-/* number of backlight levels */

-#define BACKLIGHT_LEVELS 3

-

-/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */

-#define LOCKING_SUPPORT_ENABLE

-/* Locking resynchronize hack */

-#define LOCKING_RESYNC_ENABLE

-

-/*

- * Force NKRO

- *

- * Force NKRO (nKey Rollover) to be enabled by default, regardless of the saved

- * state in the bootmagic EEPROM settings. (Note that NKRO must be enabled in the

- * makefile for this to work.)

- *

- * If forced on, NKRO can be disabled via magic key (default = LShift+RShift+N)

- * until the next keyboard reset.

- *

- * NKRO may prevent your keystrokes from being detected in the BIOS, but it is

- * fully operational during normal computer usage.

- *

- * For a less heavy-handed approach, enable NKRO via magic key (LShift+RShift+N)

- * or via bootmagic (hold SPACE+N while plugging in the keyboard). Once set by

- * bootmagic, NKRO mode will always be enabled until it is toggled again during a

- * power-up.

- *

- */

-//#define FORCE_NKRO

-

-/*

- * Magic Key Options

- *

- * Magic keys are hotkey commands that allow control over firmware functions of

- * the keyboard. They are best used in combination with the HID Listen program,

- * found here: https://www.pjrc.com/teensy/hid_listen.html

- *

- * The options below allow the magic key functionality to be changed. This is

- * useful if your keyboard/keypad is missing keys and you want magic key support.

- *

- */

-

-/* key combination for magic key command */

-#define IS_COMMAND() ( \

-  keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)) \

-)

-

-/* control how magic key switches layers */

-//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS true

-//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS true

-//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM false

-

-/* override magic key keymap */

-//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS

-//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS

-//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM

-//#define MAGIC_KEY_HELP1     H

-//#define MAGIC_KEY_HELP2     SLASH

-//#define MAGIC_KEY_DEBUG     D

-//#define MAGIC_KEY_DEBUG_MATRIX  X

-//#define MAGIC_KEY_DEBUG_KBD   K

-//#define MAGIC_KEY_DEBUG_MOUSE  M

-//#define MAGIC_KEY_VERSION    V

-//#define MAGIC_KEY_STATUS     S

-//#define MAGIC_KEY_CONSOLE    C

-//#define MAGIC_KEY_LAYER0_ALT1  ESC

-//#define MAGIC_KEY_LAYER0_ALT2  GRAVE

-//#define MAGIC_KEY_LAYER0     0

-//#define MAGIC_KEY_LAYER1     1

-//#define MAGIC_KEY_LAYER2     2

-//#define MAGIC_KEY_LAYER3     3

-//#define MAGIC_KEY_LAYER4     4

-//#define MAGIC_KEY_LAYER5     5

-//#define MAGIC_KEY_LAYER6     6

-//#define MAGIC_KEY_LAYER7     7

-//#define MAGIC_KEY_LAYER8     8

-//#define MAGIC_KEY_LAYER9     9

-//#define MAGIC_KEY_BOOTLOADER   PAUSE

-//#define MAGIC_KEY_LOCK      CAPS

-//#define MAGIC_KEY_EEPROM     E

-//#define MAGIC_KEY_NKRO      N

-//#define MAGIC_KEY_SLEEP_LED   Z

-

-/*

- * Feature disable options

- * These options are also useful to firmware size reduction.

- */

-

-/* disable debug print */

-//#define NO_DEBUG

-

-/* disable print */

-//#define NO_PRINT

-

-/* disable action features */

-//#define NO_ACTION_LAYER

-//#define NO_ACTION_TAPPING

-//#define NO_ACTION_ONESHOT

-//#define NO_ACTION_MACRO

-//#define NO_ACTION_FUNCTION

-

-#endif

+/*
+Copyright 2012 Jun Wako <wakojun@gmail.com>
+
+This program is free software: you can redistribute it and/or modify
+it under the terms of the GNU General Public License as published by
+the Free Software Foundation, either version 2 of the License, or
+(at your option) any later version.
+
+This program is distributed in the hope that it will be useful,
+but WITHOUT ANY WARRANTY; without even the implied warranty of
+MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+GNU General Public License for more details.
+
+You should have received a copy of the GNU General Public License
+along with this program. If not, see <http://www.gnu.org/licenses/>.
+*/
+
+#ifndef CONFIG_H
+#define CONFIG_H
+
+#include "config_common.h"
+
+/* USB Device descriptor parameter */
+#define VENDOR_ID    0xFEED
+#define PRODUCT_ID   0x6060
+#define DEVICE_VER   0x0001
+#define MANUFACTURER    geekhack
+#define PRODUCT         GH60
+#define DESCRIPTION     t.m.k. keyboard firmware for GH60
+
+/* key matrix size */
+#define MATRIX_ROWS 5
+#define MATRIX_COLS 14
+
+/*
+ * Keyboard Matrix Assignments
+ *
+ * Change this to how you wired your keyboard
+ * COLS: AVR pins used for columns, left to right
+ * ROWS: AVR pins used for rows, top to bottom
+ * DIODE_DIRECTION: COL2ROW = COL = Anode (+), ROW = Cathode (-, marked on diode)
+ *         ROW2COL = ROW = Anode (+), COL = Cathode (-, marked on diode)
+ *
+*/
+ #define MATRIX_ROW_PINS { D0, D1, D2, D3, D5 }
+// Rev A
+// #define MATRIX_COL_PINS { F0, F1, E6, C7, C6, B6, D4, B1, B0, B5, B4, D7, D6, B3 }
+// Rev B/C
+   #define MATRIX_COL_PINS { F0, F1, E6, C7, C6, B6, D4, B1, B7, B5, B4, D7, D6, B3 }
+#define UNUSED_PINS
+
+/* COL2ROW or ROW2COL */
+#define DIODE_DIRECTION COL2ROW
+
+/* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */
+#define DEBOUNCING_DELAY 5
+
+/* define if matrix has ghost (lacks anti-ghosting diodes) */
+//#define MATRIX_HAS_GHOST
+
+/* number of backlight levels */
+#define BACKLIGHT_LEVELS 3
+
+/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */
+#define LOCKING_SUPPORT_ENABLE
+/* Locking resynchronize hack */
+#define LOCKING_RESYNC_ENABLE
+
+/*
+ * Force NKRO
+ *
+ * Force NKRO (nKey Rollover) to be enabled by default, regardless of the saved
+ * state in the bootmagic EEPROM settings. (Note that NKRO must be enabled in the
+ * makefile for this to work.)
+ *
+ * If forced on, NKRO can be disabled via magic key (default = LShift+RShift+N)
+ * until the next keyboard reset.
+ *
+ * NKRO may prevent your keystrokes from being detected in the BIOS, but it is
+ * fully operational during normal computer usage.
+ *
+ * For a less heavy-handed approach, enable NKRO via magic key (LShift+RShift+N)
+ * or via bootmagic (hold SPACE+N while plugging in the keyboard). Once set by
+ * bootmagic, NKRO mode will always be enabled until it is toggled again during a
+ * power-up.
+ *
+ */
+//#define FORCE_NKRO
+
+/*
+ * Magic Key Options
+ *
+ * Magic keys are hotkey commands that allow control over firmware functions of
+ * the keyboard. They are best used in combination with the HID Listen program,
+ * found here: https://www.pjrc.com/teensy/hid_listen.html
+ *
+ * The options below allow the magic key functionality to be changed. This is
+ * useful if your keyboard/keypad is missing keys and you want magic key support.
+ *
+ */
+
+/* key combination for magic key command */
+#define IS_COMMAND() ( \
+  keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)) \
+)
+
+/* control how magic key switches layers */
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS true
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS true
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM false
+
+/* override magic key keymap */
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM
+//#define MAGIC_KEY_HELP1     H
+//#define MAGIC_KEY_HELP2     SLASH
+//#define MAGIC_KEY_DEBUG     D
+//#define MAGIC_KEY_DEBUG_MATRIX  X
+//#define MAGIC_KEY_DEBUG_KBD   K
+//#define MAGIC_KEY_DEBUG_MOUSE  M
+//#define MAGIC_KEY_VERSION    V
+//#define MAGIC_KEY_STATUS     S
+//#define MAGIC_KEY_CONSOLE    C
+//#define MAGIC_KEY_LAYER0_ALT1  ESC
+//#define MAGIC_KEY_LAYER0_ALT2  GRAVE
+//#define MAGIC_KEY_LAYER0     0
+//#define MAGIC_KEY_LAYER1     1
+//#define MAGIC_KEY_LAYER2     2
+//#define MAGIC_KEY_LAYER3     3
+//#define MAGIC_KEY_LAYER4     4
+//#define MAGIC_KEY_LAYER5     5
+//#define MAGIC_KEY_LAYER6     6
+//#define MAGIC_KEY_LAYER7     7
+//#define MAGIC_KEY_LAYER8     8
+//#define MAGIC_KEY_LAYER9     9
+//#define MAGIC_KEY_BOOTLOADER   PAUSE
+//#define MAGIC_KEY_LOCK      CAPS
+//#define MAGIC_KEY_EEPROM     E
+//#define MAGIC_KEY_NKRO      N
+//#define MAGIC_KEY_SLEEP_LED   Z
+
+/*
+ * Feature disable options
+ * These options are also useful to firmware size reduction.
+ */
+
+/* disable debug print */
+//#define NO_DEBUG
+
+/* disable print */
+//#define NO_PRINT
+
+/* disable action features */
+//#define NO_ACTION_LAYER
+//#define NO_ACTION_TAPPING
+//#define NO_ACTION_ONESHOT
+//#define NO_ACTION_MACRO
+//#define NO_ACTION_FUNCTION
+
+#endif
diff --git a/keyboards/gh60/gh60.c b/keyboards/gh60/gh60.c
index 255d87de99..f5a158e12f 100644
--- a/keyboards/gh60/gh60.c
+++ b/keyboards/gh60/gh60.c
@@ -1,25 +1,25 @@
-#include "gh60.h"

-

-void led_set_kb(uint8_t usb_led) {

-	// put your keyboard LED indicator (ex: Caps Lock LED) toggling code here

-	

-    if (usb_led & (1<<USB_LED_CAPS_LOCK)) {

-		gh60_caps_led_on();

-		} else {

-		gh60_caps_led_off(); 

-    }

-	

-    // if (usb_led & (1<<USB_LED_NUM_LOCK)) {

-		// gh60_esc_led_on();

-		// } else {

-		// gh60_esc_led_off(); 

-    // }

-	

-    // if (usb_led & (1<<USB_LED_SCROLL_LOCK)) {

-		// gh60_fn_led_on();

-		// } else {

-		// gh60_fn_led_off(); 	

-    // }

-

-	led_set_user(usb_led);	

-}

+#include "gh60.h"
+
+void led_set_kb(uint8_t usb_led) {
+	// put your keyboard LED indicator (ex: Caps Lock LED) toggling code here
+	
+    if (usb_led & (1<<USB_LED_CAPS_LOCK)) {
+		gh60_caps_led_on();
+		} else {
+		gh60_caps_led_off(); 
+    }
+	
+    // if (usb_led & (1<<USB_LED_NUM_LOCK)) {
+		// gh60_esc_led_on();
+		// } else {
+		// gh60_esc_led_off(); 
+    // }
+	
+    // if (usb_led & (1<<USB_LED_SCROLL_LOCK)) {
+		// gh60_fn_led_on();
+		// } else {
+		// gh60_fn_led_off(); 	
+    // }
+
+	led_set_user(usb_led);	
+}
diff --git a/keyboards/gh60/gh60.h b/keyboards/gh60/gh60.h
index ca30562a44..82624b6148 100644
--- a/keyboards/gh60/gh60.h
+++ b/keyboards/gh60/gh60.h
@@ -1,74 +1,74 @@
-#ifndef GH60_H

-#define GH60_H

-

-#include "quantum.h"

-#include "led.h"

-

-/* GH60 LEDs 

- *   GPIO pads

- *   0 F7 WASD LEDs

- *   1 F6 ESC LED

- *   2 F5 FN LED

- *   3 F4 POKER Arrow LEDs

- *   B2 Capslock LED

- *   B0 not connected

- */

-inline void gh60_caps_led_on(void)      { DDRB |=  (1<<2); PORTB &= ~(1<<2); }

-inline void gh60_poker_leds_on(void)    { DDRF |=  (1<<4); PORTF &= ~(1<<4); }

-inline void gh60_fn_led_on(void)    	{ DDRF |=  (1<<5); PORTF &= ~(1<<5); }

-inline void gh60_esc_led_on(void)    	{ DDRF |=  (1<<6); PORTF &= ~(1<<6); }

-inline void gh60_wasd_leds_on(void)    	{ DDRF |=  (1<<7); PORTF &= ~(1<<7); }

-

-inline void gh60_caps_led_off(void)     { DDRB &= ~(1<<2); PORTB &= ~(1<<2); }

-inline void gh60_poker_leds_off(void)   { DDRF &= ~(1<<4); PORTF &= ~(1<<4); }

-inline void gh60_fn_led_off(void)   	{ DDRF &= ~(1<<5); PORTF &= ~(1<<5); }

-inline void gh60_esc_led_off(void)   	{ DDRF &= ~(1<<6); PORTF &= ~(1<<6); }

-inline void gh60_wasd_leds_off(void)   	{ DDRF &= ~(1<<7); PORTF &= ~(1<<7); }

-

-/* GH60 keymap definition macro

- * K2C, K31 and  K3C are extra keys for ISO

- */

-#define KEYMAP( \

-    K00, K01, K02, K03, K04, K05, K06, K07, K08, K09, K0A, K0B, K0C, K0D, \

-    K10, K11, K12, K13, K14, K15, K16, K17, K18, K19, K1A, K1B, K1C, K1D, \

-    K20, K21, K22, K23, K24, K25, K26, K27, K28, K29, K2A, K2B, K2C, K2D, \

-    K30, K31, K32, K33, K34, K35, K36, K37, K38, K39, K3A, K3B, K3C, K3D, \

-    K40, K41, K42,           K45,                K49, K4A, K4B, K4C, K4D  \

-) { \

-    { KC_##K00, KC_##K01, KC_##K02, KC_##K03, KC_##K04, KC_##K05, KC_##K06, KC_##K07, KC_##K08, KC_##K09, KC_##K0A, KC_##K0B, KC_##K0C, KC_##K0D }, \

-    { KC_##K10, KC_##K11, KC_##K12, KC_##K13, KC_##K14, KC_##K15, KC_##K16, KC_##K17, KC_##K18, KC_##K19, KC_##K1A, KC_##K1B, KC_##K1C, KC_##K1D }, \

-    { KC_##K20, KC_##K21, KC_##K22, KC_##K23, KC_##K24, KC_##K25, KC_##K26, KC_##K27, KC_##K28, KC_##K29, KC_##K2A, KC_##K2B, KC_##K2C, KC_##K2D }, \

-    { KC_##K30, KC_##K31, KC_##K32, KC_##K33, KC_##K34, KC_##K35, KC_##K36, KC_##K37, KC_##K38, KC_##K39, KC_##K3A, KC_##K3B, KC_##K3C, KC_##K3D }, \

-    { KC_##K40, KC_##K41, KC_##K42, KC_NO,    KC_NO,    KC_##K45, KC_NO,    KC_NO,    KC_NO,    KC_##K49, KC_##K4A, KC_##K4B, KC_##K4C, KC_##K4D }  \

-}

-

-/* ANSI valiant. No extra keys for ISO */

-#define KEYMAP_ANSI( \

-    K00, K01, K02, K03, K04, K05, K06, K07, K08, K09, K0A, K0B, K0C, K0D, \

-    K10, K11, K12, K13, K14, K15, K16, K17, K18, K19, K1A, K1B, K1C, K1D, \

-    K20, K21, K22, K23, K24, K25, K26, K27, K28, K29, K2A, K2B,      K2D, \

-    K30, K32, K33, K34, K35, K36, K37, K38, K39, K3A, K3B,           K3D, \

-    K40, K41, K42,           K45,                     K4A, K4B, K4C, K4D  \

-) KEYMAP( \

-    K00, K01, K02, K03, K04, K05, K06, K07, K08, K09, K0A, K0B, K0C, K0D, \

-    K10, K11, K12, K13, K14, K15, K16, K17, K18, K19, K1A, K1B, K1C, K1D, \

-    K20, K21, K22, K23, K24, K25, K26, K27, K28, K29, K2A, K2B, NO,  K2D, \

-    K30, NO,  K32, K33, K34, K35, K36, K37, K38, K39, K3A, K3B, NO,  K3D, \

-    K40, K41, K42,           K45,                NO,  K4A, K4B, K4C, K4D  \

-)

-

-#define KEYMAP_HHKB( \

-    K00, K01, K02, K03, K04, K05, K06, K07, K08, K09, K0A, K0B, K0C, K0D, K49,\

-    K10, K11, K12, K13, K14, K15, K16, K17, K18, K19, K1A, K1B, K1C, K1D, \

-    K20, K21, K22, K23, K24, K25, K26, K27, K28, K29, K2A, K2B,      K2D, \

-    K30, K32, K33, K34, K35, K36, K37, K38, K39, K3A, K3B,      K3D, K3C, \

-    K40, K41, K42,           K45,                     K4A, K4B, K4C, K4D  \

-) KEYMAP( \

-    K00, K01, K02, K03, K04, K05, K06, K07, K08, K09, K0A, K0B, K0C, K0D, \

-    K10, K11, K12, K13, K14, K15, K16, K17, K18, K19, K1A, K1B, K1C, K1D, \

-    K20, K21, K22, K23, K24, K25, K26, K27, K28, K29, K2A, K2B, NO,  K2D, \

-    K30, NO,  K32, K33, K34, K35, K36, K37, K38, K39, K3A, K3B, K3C, K3D, \

-    K40, K41, K42,           K45,                K49, K4A, K4B, K4C, K4D  \

-)

-

-#endif

+#ifndef GH60_H
+#define GH60_H
+
+#include "quantum.h"
+#include "led.h"
+
+/* GH60 LEDs 
+ *   GPIO pads
+ *   0 F7 WASD LEDs
+ *   1 F6 ESC LED
+ *   2 F5 FN LED
+ *   3 F4 POKER Arrow LEDs
+ *   B2 Capslock LED
+ *   B0 not connected
+ */
+inline void gh60_caps_led_on(void)      { DDRB |=  (1<<2); PORTB &= ~(1<<2); }
+inline void gh60_poker_leds_on(void)    { DDRF |=  (1<<4); PORTF &= ~(1<<4); }
+inline void gh60_fn_led_on(void)    	{ DDRF |=  (1<<5); PORTF &= ~(1<<5); }
+inline void gh60_esc_led_on(void)    	{ DDRF |=  (1<<6); PORTF &= ~(1<<6); }
+inline void gh60_wasd_leds_on(void)    	{ DDRF |=  (1<<7); PORTF &= ~(1<<7); }
+
+inline void gh60_caps_led_off(void)     { DDRB &= ~(1<<2); PORTB &= ~(1<<2); }
+inline void gh60_poker_leds_off(void)   { DDRF &= ~(1<<4); PORTF &= ~(1<<4); }
+inline void gh60_fn_led_off(void)   	{ DDRF &= ~(1<<5); PORTF &= ~(1<<5); }
+inline void gh60_esc_led_off(void)   	{ DDRF &= ~(1<<6); PORTF &= ~(1<<6); }
+inline void gh60_wasd_leds_off(void)   	{ DDRF &= ~(1<<7); PORTF &= ~(1<<7); }
+
+/* GH60 keymap definition macro
+ * K2C, K31 and  K3C are extra keys for ISO
+ */
+#define KEYMAP( \
+    K00, K01, K02, K03, K04, K05, K06, K07, K08, K09, K0A, K0B, K0C, K0D, \
+    K10, K11, K12, K13, K14, K15, K16, K17, K18, K19, K1A, K1B, K1C, K1D, \
+    K20, K21, K22, K23, K24, K25, K26, K27, K28, K29, K2A, K2B, K2C, K2D, \
+    K30, K31, K32, K33, K34, K35, K36, K37, K38, K39, K3A, K3B, K3C, K3D, \
+    K40, K41, K42,           K45,                K49, K4A, K4B, K4C, K4D  \
+) { \
+    { KC_##K00, KC_##K01, KC_##K02, KC_##K03, KC_##K04, KC_##K05, KC_##K06, KC_##K07, KC_##K08, KC_##K09, KC_##K0A, KC_##K0B, KC_##K0C, KC_##K0D }, \
+    { KC_##K10, KC_##K11, KC_##K12, KC_##K13, KC_##K14, KC_##K15, KC_##K16, KC_##K17, KC_##K18, KC_##K19, KC_##K1A, KC_##K1B, KC_##K1C, KC_##K1D }, \
+    { KC_##K20, KC_##K21, KC_##K22, KC_##K23, KC_##K24, KC_##K25, KC_##K26, KC_##K27, KC_##K28, KC_##K29, KC_##K2A, KC_##K2B, KC_##K2C, KC_##K2D }, \
+    { KC_##K30, KC_##K31, KC_##K32, KC_##K33, KC_##K34, KC_##K35, KC_##K36, KC_##K37, KC_##K38, KC_##K39, KC_##K3A, KC_##K3B, KC_##K3C, KC_##K3D }, \
+    { KC_##K40, KC_##K41, KC_##K42, KC_NO,    KC_NO,    KC_##K45, KC_NO,    KC_NO,    KC_NO,    KC_##K49, KC_##K4A, KC_##K4B, KC_##K4C, KC_##K4D }  \
+}
+
+/* ANSI valiant. No extra keys for ISO */
+#define KEYMAP_ANSI( \
+    K00, K01, K02, K03, K04, K05, K06, K07, K08, K09, K0A, K0B, K0C, K0D, \
+    K10, K11, K12, K13, K14, K15, K16, K17, K18, K19, K1A, K1B, K1C, K1D, \
+    K20, K21, K22, K23, K24, K25, K26, K27, K28, K29, K2A, K2B,      K2D, \
+    K30, K32, K33, K34, K35, K36, K37, K38, K39, K3A, K3B,           K3D, \
+    K40, K41, K42,           K45,                     K4A, K4B, K4C, K4D  \
+) KEYMAP( \
+    K00, K01, K02, K03, K04, K05, K06, K07, K08, K09, K0A, K0B, K0C, K0D, \
+    K10, K11, K12, K13, K14, K15, K16, K17, K18, K19, K1A, K1B, K1C, K1D, \
+    K20, K21, K22, K23, K24, K25, K26, K27, K28, K29, K2A, K2B, NO,  K2D, \
+    K30, NO,  K32, K33, K34, K35, K36, K37, K38, K39, K3A, K3B, NO,  K3D, \
+    K40, K41, K42,           K45,                NO,  K4A, K4B, K4C, K4D  \
+)
+
+#define KEYMAP_HHKB( \
+    K00, K01, K02, K03, K04, K05, K06, K07, K08, K09, K0A, K0B, K0C, K0D, K49,\
+    K10, K11, K12, K13, K14, K15, K16, K17, K18, K19, K1A, K1B, K1C, K1D, \
+    K20, K21, K22, K23, K24, K25, K26, K27, K28, K29, K2A, K2B,      K2D, \
+    K30, K32, K33, K34, K35, K36, K37, K38, K39, K3A, K3B,      K3D, K3C, \
+    K40, K41, K42,           K45,                     K4A, K4B, K4C, K4D  \
+) KEYMAP( \
+    K00, K01, K02, K03, K04, K05, K06, K07, K08, K09, K0A, K0B, K0C, K0D, \
+    K10, K11, K12, K13, K14, K15, K16, K17, K18, K19, K1A, K1B, K1C, K1D, \
+    K20, K21, K22, K23, K24, K25, K26, K27, K28, K29, K2A, K2B, NO,  K2D, \
+    K30, NO,  K32, K33, K34, K35, K36, K37, K38, K39, K3A, K3B, K3C, K3D, \
+    K40, K41, K42,           K45,                K49, K4A, K4B, K4C, K4D  \
+)
+
+#endif
diff --git a/keyboards/gh60/keymaps/robotmaxtron/Makefile b/keyboards/gh60/keymaps/robotmaxtron/Makefile
index 2e69aee298..c73cf11417 100644
--- a/keyboards/gh60/keymaps/robotmaxtron/Makefile
+++ b/keyboards/gh60/keymaps/robotmaxtron/Makefile
@@ -1,112 +1,112 @@
-#----------------------------------------------------------------------------

-# On command line:

-#

-# make all = Make software.

-#

-# make clean = Clean out built project files.

-#

-# make coff = Convert ELF to AVR COFF.

-#

-# make extcoff = Convert ELF to AVR Extended COFF.

-#

-# make program = Download the hex file to the device.

-#                Please customize your programmer settings(PROGRAM_CMD)

-#

-# make teensy = Download the hex file to the device, using teensy_loader_cli.

-#               (must have teensy_loader_cli installed).

-#

-# make dfu = Download the hex file to the device, using dfu-programmer (must

-#            have dfu-programmer installed).

-#

-# make flip = Download the hex file to the device, using Atmel FLIP (must

-#             have Atmel FLIP installed).

-#

-# make dfu-ee = Download the eeprom file to the device, using dfu-programmer

-#               (must have dfu-programmer installed).

-#

-# make flip-ee = Download the eeprom file to the device, using Atmel FLIP

-#                (must have Atmel FLIP installed).

-#

-# make debug = Start either simulavr or avarice as specified for debugging, 

-#              with avr-gdb or avr-insight as the front end for debugging.

-#

-# make filename.s = Just compile filename.c into the assembler code only.

-#

-# make filename.i = Create a preprocessed source file for use in submitting

-#                   bug reports to the GCC project.

-#

-# To rebuild project do "make clean" then "make all".

-#----------------------------------------------------------------------------

-

-# MCU name

-#MCU = at90usb1287

-MCU = atmega32u4

-

-# Processor frequency.

-#     This will define a symbol, F_CPU, in all source code files equal to the

-#     processor frequency in Hz. You can then use this symbol in your source code to

-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done

-#     automatically to create a 32-bit value in your source code.

-#

-#     This will be an integer division of F_USB below, as it is sourced by

-#     F_USB after it has run through any CPU prescalers. Note that this value

-#     does not *change* the processor frequency - it should merely be updated to

-#     reflect the processor speed set externally so that the code can use accurate

-#     software delays.

-F_CPU = 16000000

-

-

-#

-# LUFA specific

-#

-# Target architecture (see library "Board Types" documentation).

-ARCH = AVR8

-

-# Input clock frequency.

-#     This will define a symbol, F_USB, in all source code files equal to the

-#     input clock frequency (before any prescaling is performed) in Hz. This value may

-#     differ from F_CPU if prescaling is used on the latter, and is required as the

-#     raw input clock is fed directly to the PLL sections of the AVR for high speed

-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'

-#     at the end, this will be done automatically to create a 32-bit value in your

-#     source code.

-#

-#     If no clock division is performed on the input clock inside the AVR (via the

-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.

-F_USB = $(F_CPU)

-

-# Interrupt driven control endpoint task(+60)

-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT

-

-

-# Boot Section Size in *bytes*

-#   Teensy halfKay   512

-#   Teensy++ halfKay 1024

-#   Atmel DFU loader 4096

-#   LUFA bootloader  4096

-#   USBaspLoader     2048

-OPT_DEFS += -DBOOTLOADER_SIZE=4096

-

-

-# Build Options

-#   comment out to disable the options.

-#

-BOOTMAGIC_ENABLE ?= yes		# Virtual DIP switch configuration(+1000)

-MOUSEKEY_ENABLE ?= yes		# Mouse keys(+4700)

-EXTRAKEY_ENABLE ?= yes		# Audio control and System control(+450)

-# CONSOLE_ENABLE ?= yes		# Console for debug(+400)

-# COMMAND_ENABLE ?= yes		# Commands for debug and configuration

-KEYBOARD_LOCK_ENABLE ?= yes	# Allow locking of keyboard via magic key

-# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE

-# SLEEP_LED_ENABLE ?= yes	# Breathing sleep LED during USB suspend

-NKRO_ENABLE ?= yes		# USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work

-# BACKLIGHT_ENABLE ?= yes	# Enable keyboard backlight functionality

-# MIDI_ENABLE ?= YES		# MIDI controls

-# UNICODE_ENABLE ?= YES		# Unicode

-# BLUETOOTH_ENABLE ?= yes	# Enable Bluetooth with the Adafruit EZ-Key HID

-RGBLIGHT_ENABLE ?= yes          # Enable RGB Underglow

-

-ifndef QUANTUM_DIR

-	include ../../../../Makefile

-endif

-

+#----------------------------------------------------------------------------
+# On command line:
+#
+# make all = Make software.
+#
+# make clean = Clean out built project files.
+#
+# make coff = Convert ELF to AVR COFF.
+#
+# make extcoff = Convert ELF to AVR Extended COFF.
+#
+# make program = Download the hex file to the device.
+#                Please customize your programmer settings(PROGRAM_CMD)
+#
+# make teensy = Download the hex file to the device, using teensy_loader_cli.
+#               (must have teensy_loader_cli installed).
+#
+# make dfu = Download the hex file to the device, using dfu-programmer (must
+#            have dfu-programmer installed).
+#
+# make flip = Download the hex file to the device, using Atmel FLIP (must
+#             have Atmel FLIP installed).
+#
+# make dfu-ee = Download the eeprom file to the device, using dfu-programmer
+#               (must have dfu-programmer installed).
+#
+# make flip-ee = Download the eeprom file to the device, using Atmel FLIP
+#                (must have Atmel FLIP installed).
+#
+# make debug = Start either simulavr or avarice as specified for debugging, 
+#              with avr-gdb or avr-insight as the front end for debugging.
+#
+# make filename.s = Just compile filename.c into the assembler code only.
+#
+# make filename.i = Create a preprocessed source file for use in submitting
+#                   bug reports to the GCC project.
+#
+# To rebuild project do "make clean" then "make all".
+#----------------------------------------------------------------------------
+
+# MCU name
+#MCU = at90usb1287
+MCU = atmega32u4
+
+# Processor frequency.
+#     This will define a symbol, F_CPU, in all source code files equal to the
+#     processor frequency in Hz. You can then use this symbol in your source code to
+#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
+#     automatically to create a 32-bit value in your source code.
+#
+#     This will be an integer division of F_USB below, as it is sourced by
+#     F_USB after it has run through any CPU prescalers. Note that this value
+#     does not *change* the processor frequency - it should merely be updated to
+#     reflect the processor speed set externally so that the code can use accurate
+#     software delays.
+F_CPU = 16000000
+
+
+#
+# LUFA specific
+#
+# Target architecture (see library "Board Types" documentation).
+ARCH = AVR8
+
+# Input clock frequency.
+#     This will define a symbol, F_USB, in all source code files equal to the
+#     input clock frequency (before any prescaling is performed) in Hz. This value may
+#     differ from F_CPU if prescaling is used on the latter, and is required as the
+#     raw input clock is fed directly to the PLL sections of the AVR for high speed
+#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
+#     at the end, this will be done automatically to create a 32-bit value in your
+#     source code.
+#
+#     If no clock division is performed on the input clock inside the AVR (via the
+#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
+F_USB = $(F_CPU)
+
+# Interrupt driven control endpoint task(+60)
+OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
+
+
+# Boot Section Size in *bytes*
+#   Teensy halfKay   512
+#   Teensy++ halfKay 1024
+#   Atmel DFU loader 4096
+#   LUFA bootloader  4096
+#   USBaspLoader     2048
+OPT_DEFS += -DBOOTLOADER_SIZE=4096
+
+
+# Build Options
+#   comment out to disable the options.
+#
+BOOTMAGIC_ENABLE ?= yes		# Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE ?= yes		# Mouse keys(+4700)
+EXTRAKEY_ENABLE ?= yes		# Audio control and System control(+450)
+# CONSOLE_ENABLE ?= yes		# Console for debug(+400)
+# COMMAND_ENABLE ?= yes		# Commands for debug and configuration
+KEYBOARD_LOCK_ENABLE ?= yes	# Allow locking of keyboard via magic key
+# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
+# SLEEP_LED_ENABLE ?= yes	# Breathing sleep LED during USB suspend
+NKRO_ENABLE ?= yes		# USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
+# BACKLIGHT_ENABLE ?= yes	# Enable keyboard backlight functionality
+# MIDI_ENABLE ?= YES		# MIDI controls
+# UNICODE_ENABLE ?= YES		# Unicode
+# BLUETOOTH_ENABLE ?= yes	# Enable Bluetooth with the Adafruit EZ-Key HID
+RGBLIGHT_ENABLE ?= yes          # Enable RGB Underglow
+
+ifndef QUANTUM_DIR
+	include ../../../../Makefile
+endif
+
diff --git a/keyboards/gh60/keymaps/robotmaxtron/config.h b/keyboards/gh60/keymaps/robotmaxtron/config.h
index 8272875ed0..6a29e6b8c2 100644
--- a/keyboards/gh60/keymaps/robotmaxtron/config.h
+++ b/keyboards/gh60/keymaps/robotmaxtron/config.h
@@ -1,190 +1,190 @@
-/*

-Copyright 2012 Jun Wako <wakojun@gmail.com>

-

-This program is free software: you can redistribute it and/or modify

-it under the terms of the GNU General Public License as published by

-the Free Software Foundation, either version 2 of the License, or

-(at your option) any later version.

-

-This program is distributed in the hope that it will be useful,

-but WITHOUT ANY WARRANTY; without even the implied warranty of

-MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the

-GNU General Public License for more details.

-

-You should have received a copy of the GNU General Public License

-along with this program. If not, see <http://www.gnu.org/licenses/>.

-*/

-

-#ifndef CONFIG_H

-#define CONFIG_H

-

-#include "config_common.h"

-

-/* USB Device descriptor parameter */

-#define VENDOR_ID    0xFEED

-#define PRODUCT_ID   0x6060

-#define DEVICE_VER   0x0001

-#define MANUFACTURER    geekhack

-#define PRODUCT         GH60

-#define DESCRIPTION     t.m.k. keyboard firmware for GH60

-

-/* key matrix size */

-#define MATRIX_ROWS 5

-#define MATRIX_COLS 14

-

-/*

- * Keyboard