Clean up some user keymaps specifying MCU (#11966)

1 files changed, 1 insertions, 107 deletions

diff --git a/keyboards/gh60/revc/keymaps/dbroqua_7U/rules.mk b/keyboards/gh60/revc/keymaps/dbroqua_7U/rules.mk
index 21192b1794..9e00b7531a 100644
--- a/keyboards/gh60/revc/keymaps/dbroqua_7U/rules.mk
+++ b/keyboards/gh60/revc/keymaps/dbroqua_7U/rules.mk
@@ -1,107 +1 @@
-#----------------------------------------------------------------------------
-# On command line:
-#
-# make all = Make software.
-#
-# make clean = Clean out built project files.
-#
-# make coff = Convert ELF to AVR COFF.
-#
-# make extcoff = Convert ELF to AVR Extended COFF.
-#
-# make program = Download the hex file to the device.
-#                Please customize your programmer settings(PROGRAM_CMD)
-#
-# make teensy = Download the hex file to the device, using teensy_loader_cli.
-#               (must have teensy_loader_cli installed).
-#
-# make dfu = Download the hex file to the device, using dfu-programmer (must
-#            have dfu-programmer installed).
-#
-# make flip = Download the hex file to the device, using Atmel FLIP (must
-#             have Atmel FLIP installed).
-#
-# make dfu-ee = Download the eeprom file to the device, using dfu-programmer
-#               (must have dfu-programmer installed).
-#
-# make flip-ee = Download the eeprom file to the device, using Atmel FLIP
-#                (must have Atmel FLIP installed).
-#
-# make debug = Start either simulavr or avarice as specified for debugging, 
-#              with avr-gdb or avr-insight as the front end for debugging.
-#
-# make filename.s = Just compile filename.c into the assembler code only.
-#
-# make filename.i = Create a preprocessed source file for use in submitting
-#                   bug reports to the GCC project.
-#
-# To rebuild project do "make clean" then "make all".
-#----------------------------------------------------------------------------
-
-# MCU name
-MCU = atmega32u4
-
-# Processor frequency.
-#     This will define a symbol, F_CPU, in all source code files equal to the
-#     processor frequency in Hz. You can then use this symbol in your source code to
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-#     automatically to create a 32-bit value in your source code.
-#
-#     This will be an integer division of F_USB below, as it is sourced by
-#     F_USB after it has run through any CPU prescalers. Note that this value
-#     does not *change* the processor frequency - it should merely be updated to
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
-# Boot Section Size in *bytes*
-#   Teensy halfKay   512
-#   Teensy++ halfKay 1024
-#   Atmel DFU loader 4096
-#   LUFA bootloader  4096
-#   USBaspLoader     2048
-OPT_DEFS += -DBOOTLOADER_SIZE=4096
-
-
-# Build Options
-#   comment out to disable the options.
-#
-BOOTMAGIC_ENABLE = yes		# Virtual DIP switch configuration(+1000)
-MOUSEKEY_ENABLE = yes		# Mouse keys(+4700)
-EXTRAKEY_ENABLE = yes		# Audio control and System control(+450)
-# CONSOLE_ENABLE = yes		# Console for debug(+400)
-# COMMAND_ENABLE = yes		# Commands for debug and configuration
-KEYBOARD_LOCK_ENABLE = yes	# Allow locking of keyboard via magic key
-# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
-SLEEP_LED_ENABLE = yes	    # Breathing sleep LED during USB suspend
-NKRO_ENABLE = yes		    # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
-# BACKLIGHT_ENABLE = yes	# Enable keyboard backlight functionality
-# MIDI_ENABLE = YES		# MIDI controls
-# UNICODE_ENABLE = YES		# Unicode
-# BLUETOOTH_ENABLE = yes	# Enable Bluetooth with the Adafruit EZ-Key HID
-RGBLIGHT_ENABLE = no    # Enable RGB Underglow
-
+SLEEP_LED_ENABLE = yes