Merge remote-tracking branch 'upstream/master'

* upstream/master: (1239 commits)
  Update ez.c
  removes planck/rev3 temporarily
  Move hand_swap_config to ez.c, removes error for infinity
  Update Makefile
  ergodox: Update algernon's keymap to v1.9
  Added VS Code dir to .gitignore
  Support the Pegasus Hoof controller.
  [Jack & Erez] Simplifies and documents TO
  add readme
  use wait_ms instead of _delay_ms
  add messenger
  init keymap
  Add example keymap
  Adding whiskey_tango_foxtrot_capslock ergodox keymap
  Unicode map framework. Allow unicode up to 0xFFFFF using separate mapping table
  CIE 1931 dim curve
  Apply the dim curve to the RGB output
  Update the Cluecard readme files
  Tune snake and knight intervals for Cluecard
  Tunable RGB light intervals
  ...

1 files changed, 74 insertions, 0 deletions

diff --git a/keyboards/ergodox/infinity/mcuconf.h b/keyboards/ergodox/infinity/mcuconf.h
new file mode 100644
index 0000000000..f6730b99ca
--- /dev/null
+++ b/keyboards/ergodox/infinity/mcuconf.h
@@ -0,0 +1,74 @@
+/*
+    ChibiOS - Copyright (C) 2006..2015 Giovanni Di Sirio
+
+    Licensed under the Apache License, Version 2.0 (the "License");
+    you may not use this file except in compliance with the License.
+    You may obtain a copy of the License at
+
+        http://www.apache.org/licenses/LICENSE-2.0
+
+    Unless required by applicable law or agreed to in writing, software
+    distributed under the License is distributed on an "AS IS" BASIS,
+    WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+    See the License for the specific language governing permissions and
+    limitations under the License.
+*/
+
+#ifndef _MCUCONF_H_
+#define _MCUCONF_H_
+
+#define K20x_MCUCONF
+
+/*
+ * HAL driver system settings.
+ */
+
+#define K20x7
+
+/* Select the MCU clocking mode below by enabling the appropriate block. */
+
+#define KINETIS_NO_INIT             FALSE
+
+/* PEE mode - 48MHz system clock driven by external crystal. */
+#define KINETIS_MCG_MODE            KINETIS_MCG_MODE_PEE
+#define KINETIS_PLLCLK_FREQUENCY    72000000UL
+#define KINETIS_SYSCLK_FREQUENCY    72000000UL
+#define KINETIS_BUSCLK_FREQUENCY    36000000UL
+#define KINETIS_FLASHCLK_FREQUENCY  24000000UL
+
+#if 0
+/* FEI mode - 48 MHz with internal 32.768 kHz crystal */
+#define KINETIS_MCG_MODE            KINETIS_MCG_MODE_FEI
+#define KINETIS_MCG_FLL_DMX32       1           /* Fine-tune for 32.768 kHz */
+#define KINETIS_MCG_FLL_DRS         1           /* 1464x FLL factor */
+#define KINETIS_SYSCLK_FREQUENCY    47972352UL  /* 32.768 kHz * 1464 (~48 MHz) */
+#define KINETIS_CLKDIV1_OUTDIV1     1
+#define KINETIS_CLKDIV1_OUTDIV2     1
+#define KINETIS_CLKDIV1_OUTDIV4     2
+#define KINETIS_BUSCLK_FREQUENCY    KINETIS_SYSCLK_FREQUENCY
+#define KINETIS_FLASHCLK_FREQUENCY  KINETIS_SYSCLK_FREQUENCY/2
+#endif
+
+/*
+ * SERIAL driver system settings.
+ */
+#define KINETIS_SERIAL_USE_UART0            TRUE
+#define KINETIS_SERIAL_USE_UART1            TRUE
+
+/*
+ * USB driver settings
+ */
+#define KINETIS_USB_USE_USB0                TRUE
+/* Need to redefine this, since the default is for K20x */
+/* This is for Teensy LC; you should comment it out (or change to 5)
+ * for Teensy 3.x */
+#define KINETIS_USB_USB0_IRQ_PRIORITY       2
+
+/*
+ * SPI driver system settings.
+ */
+#define KINETIS_SPI_USE_SPI0                TRUE
+
+#define KINETIS_I2C_USE_I2C0                TRUE
+
+#endif /* _MCUCONF_H_ */