Merge pull request #3 from jackhumbert/master

Merge from jackhumbert

2 files changed, 78 insertions, 75 deletions

diff --git a/keyboards/ergodox/ez/Makefile b/keyboards/ergodox/ez/Makefile
index 37e554b304..191c6bb664 100644
--- a/keyboards/ergodox/ez/Makefile
+++ b/keyboards/ergodox/ez/Makefile
@@ -1,76 +1,3 @@
-#----------------------------------------------------------------------------
-# On command line:
-#
-# make = Make software.
-#
-# make clean = Clean out built project files.
-#
-# That's pretty much all you need. To compile, always go make clean, 
-# followed by make.
-#
-# For advanced users only:
-# make teensy = Download the hex file to the device, using teensy_loader_cli.
-#               (must have teensy_loader_cli installed).
-#
-#----------------------------------------------------------------------------
-
-# # project specific files
-SRC = twimaster.c \
-	  matrix.c
-
-# MCU name
-MCU = atmega32u4
-
-# Processor frequency.
-#     This will define a symbol, F_CPU, in all source code files equal to the
-#     processor frequency in Hz. You can then use this symbol in your source code to
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-#     automatically to create a 32-bit value in your source code.
-#
-#     This will be an integer division of F_USB below, as it is sourced by
-#     F_USB after it has run through any CPU prescalers. Note that this value
-#     does not *change* the processor frequency - it should merely be updated to
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
-# Boot Section Size in *bytes*
-#   Teensy halfKay   512
-#   Teensy++ halfKay 1024
-#   Atmel DFU loader 4096
-#   LUFA bootloader  4096
-#   USBaspLoader     2048
-OPT_DEFS += -DBOOTLOADER_SIZE=512
-
-
-# Build Options
-#   comment out to disable the options.
-#
-
-ifndef QUANTUM_DIR
+ifndef MAKEFILE_INCLUDED
 	include ../../../Makefile
-endif
+endif
\ No newline at end of file
diff --git a/keyboards/ergodox/ez/rules.mk b/keyboards/ergodox/ez/rules.mk
new file mode 100644
index 0000000000..37e554b304
--- /dev/null
+++ b/keyboards/ergodox/ez/rules.mk
@@ -0,0 +1,76 @@
+#----------------------------------------------------------------------------
+# On command line:
+#
+# make = Make software.
+#
+# make clean = Clean out built project files.
+#
+# That's pretty much all you need. To compile, always go make clean, 
+# followed by make.
+#
+# For advanced users only:
+# make teensy = Download the hex file to the device, using teensy_loader_cli.
+#               (must have teensy_loader_cli installed).
+#
+#----------------------------------------------------------------------------
+
+# # project specific files
+SRC = twimaster.c \
+	  matrix.c
+
+# MCU name
+MCU = atmega32u4
+
+# Processor frequency.
+#     This will define a symbol, F_CPU, in all source code files equal to the
+#     processor frequency in Hz. You can then use this symbol in your source code to
+#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
+#     automatically to create a 32-bit value in your source code.
+#
+#     This will be an integer division of F_USB below, as it is sourced by
+#     F_USB after it has run through any CPU prescalers. Note that this value
+#     does not *change* the processor frequency - it should merely be updated to
+#     reflect the processor speed set externally so that the code can use accurate
+#     software delays.
+F_CPU = 16000000
+
+
+#
+# LUFA specific
+#
+# Target architecture (see library "Board Types" documentation).
+ARCH = AVR8
+
+# Input clock frequency.
+#     This will define a symbol, F_USB, in all source code files equal to the
+#     input clock frequency (before any prescaling is performed) in Hz. This value may
+#     differ from F_CPU if prescaling is used on the latter, and is required as the
+#     raw input clock is fed directly to the PLL sections of the AVR for high speed
+#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
+#     at the end, this will be done automatically to create a 32-bit value in your
+#     source code.
+#
+#     If no clock division is performed on the input clock inside the AVR (via the
+#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
+F_USB = $(F_CPU)
+
+# Interrupt driven control endpoint task(+60)
+OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
+
+
+# Boot Section Size in *bytes*
+#   Teensy halfKay   512
+#   Teensy++ halfKay 1024
+#   Atmel DFU loader 4096
+#   LUFA bootloader  4096
+#   USBaspLoader     2048
+OPT_DEFS += -DBOOTLOADER_SIZE=512
+
+
+# Build Options
+#   comment out to disable the options.
+#
+
+ifndef QUANTUM_DIR
+	include ../../../Makefile
+endif