Merge remote-tracking branch 'upstream/master'

3 files changed, 75 insertions, 78 deletions

diff --git a/keyboards/cluecard/Makefile b/keyboards/cluecard/Makefile
index 029d0b9670..4e2a6f00fd 100644
--- a/keyboards/cluecard/Makefile
+++ b/keyboards/cluecard/Makefile
@@ -1,76 +1,3 @@
-
-
-# MCU name
-#MCU = at90usb1287
-MCU = atmega32u4
-
-# Processor frequency.
-#     This will define a symbol, F_CPU, in all source code files equal to the
-#     processor frequency in Hz. You can then use this symbol in your source code to
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-#     automatically to create a 32-bit value in your source code.
-#
-#     This will be an integer division of F_USB below, as it is sourced by
-#     F_USB after it has run through any CPU prescalers. Note that this value
-#     does not *change* the processor frequency - it should merely be updated to
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
-# Boot Section Size in *bytes*
-#   Teensy halfKay   512
-#   Teensy++ halfKay 1024
-#   Atmel DFU loader 4096
-#   LUFA bootloader  4096
-#   USBaspLoader     2048
-OPT_DEFS += -DBOOTLOADER_SIZE=4096
-
-
-# Build Options
-#   change yes to no to disable
-#
-BOOTMAGIC_ENABLE ?= no      # Virtual DIP switch configuration(+1000)
-MOUSEKEY_ENABLE ?= yes       # Mouse keys(+4700)
-EXTRAKEY_ENABLE ?= yes       # Audio control and System control(+450)
-CONSOLE_ENABLE ?= yes        # Console for debug(+400)
-COMMAND_ENABLE ?= yes        # Commands for debug and configuration
-# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
-SLEEP_LED_ENABLE ?= no       # Breathing sleep LED during USB suspend
-# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
-NKRO_ENABLE ?= no            # USB Nkey Rollover
-RGBLIGHT_ENABLE ?= yes       # Enable keyboard underlight functionality (+4870)
-BACKLIGHT_ENABLE ?= yes       # Enable keyboard backlight functionality by default
-MIDI_ENABLE ?= no            # MIDI controls
-UNICODE_ENABLE ?= no         # Unicode
-BLUETOOTH_ENABLE ?= no       # Enable Bluetooth with the Adafruit EZ-Key HID
-AUDIO_ENABLE ?= yes           # Audio output on port C6
-
-ifndef QUANTUM_DIR
+ifndef MAKEFILE_INCLUDED
 	include ../../Makefile
-endif
-
-
+endif
\ No newline at end of file
diff --git a/keyboards/cluecard/readme.md b/keyboards/cluecard/readme.md
index ae1afbbfdd..be13fc0171 100644
--- a/keyboards/cluecard/readme.md
+++ b/keyboards/cluecard/readme.md
@@ -13,16 +13,16 @@ Depending on which keymap you would like to use, you will have to compile slight
 
 ### Default
 
-To build with the default keymap, simply run `make`.
+To build with the default keymap, simply run `make default`.
 
 ### Other Keymaps
 
 Several version of keymap are available in advance but you are recommended to define your favorite layout yourself. To define your own keymap create a folder with the name of your keymap in the keymaps folder, and see keymap documentation (you can find in top readme.md) and existant keymap files.
 
-To build the firmware binary hex file with a keymap just do `make` with `keymap` option like:
+To build the firmware binary hex file with a keymap just do `make` with a keymap like this:
 
 ```
-$ make keymap=[default|jack|<name>]
+$ make [default|jack|<name>]
 ```
 
 Keymaps follow the format **__keymap.c__** and are stored in folders in the `keymaps` folder, eg `keymaps/my_keymap/`
diff --git a/keyboards/cluecard/rules.mk b/keyboards/cluecard/rules.mk
new file mode 100644
index 0000000000..454235877d
--- /dev/null
+++ b/keyboards/cluecard/rules.mk
@@ -0,0 +1,70 @@
+
+
+# MCU name
+#MCU = at90usb1287
+MCU = atmega32u4
+
+# Processor frequency.
+#     This will define a symbol, F_CPU, in all source code files equal to the
+#     processor frequency in Hz. You can then use this symbol in your source code to
+#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
+#     automatically to create a 32-bit value in your source code.
+#
+#     This will be an integer division of F_USB below, as it is sourced by
+#     F_USB after it has run through any CPU prescalers. Note that this value
+#     does not *change* the processor frequency - it should merely be updated to
+#     reflect the processor speed set externally so that the code can use accurate
+#     software delays.
+F_CPU = 16000000
+
+
+#
+# LUFA specific
+#
+# Target architecture (see library "Board Types" documentation).
+ARCH = AVR8
+
+# Input clock frequency.
+#     This will define a symbol, F_USB, in all source code files equal to the
+#     input clock frequency (before any prescaling is performed) in Hz. This value may
+#     differ from F_CPU if prescaling is used on the latter, and is required as the
+#     raw input clock is fed directly to the PLL sections of the AVR for high speed
+#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
+#     at the end, this will be done automatically to create a 32-bit value in your
+#     source code.
+#
+#     If no clock division is performed on the input clock inside the AVR (via the
+#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
+F_USB = $(F_CPU)
+
+# Interrupt driven control endpoint task(+60)
+OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
+
+
+# Boot Section Size in *bytes*
+#   Teensy halfKay   512
+#   Teensy++ halfKay 1024
+#   Atmel DFU loader 4096
+#   LUFA bootloader  4096
+#   USBaspLoader     2048
+OPT_DEFS += -DBOOTLOADER_SIZE=4096
+
+
+# Build Options
+#   change yes to no to disable
+#
+BOOTMAGIC_ENABLE ?= no      # Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE ?= yes       # Mouse keys(+4700)
+EXTRAKEY_ENABLE ?= yes       # Audio control and System control(+450)
+CONSOLE_ENABLE ?= yes        # Console for debug(+400)
+COMMAND_ENABLE ?= yes        # Commands for debug and configuration
+# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
+SLEEP_LED_ENABLE ?= no       # Breathing sleep LED during USB suspend
+# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
+NKRO_ENABLE ?= no            # USB Nkey Rollover
+RGBLIGHT_ENABLE ?= yes       # Enable keyboard underlight functionality (+4870)
+BACKLIGHT_ENABLE ?= yes       # Enable keyboard backlight functionality by default
+MIDI_ENABLE ?= no            # MIDI controls
+UNICODE_ENABLE ?= no         # Unicode
+BLUETOOTH_ENABLE ?= no       # Enable Bluetooth with the Adafruit EZ-Key HID
+AUDIO_ENABLE ?= yes           # Audio output on port C6