Merge remote-tracking branch 'upstream/master'

1 files changed, 103 insertions, 0 deletions

diff --git a/keyboards/clueboard/rules.mk b/keyboards/clueboard/rules.mk
new file mode 100644
index 0000000000..3909fbd5cb
--- /dev/null
+++ b/keyboards/clueboard/rules.mk
@@ -0,0 +1,103 @@
+#----------------------------------------------------------------------------
+# On command line:
+#
+# make all = Make software.
+#
+# make clean = Clean out built project files.
+#
+# make coff = Convert ELF to AVR COFF.
+#
+# make extcoff = Convert ELF to AVR Extended COFF.
+#
+# make program = Download the hex file to the device.
+#                Please customize your programmer settings(PROGRAM_CMD)
+#
+# make teensy = Download the hex file to the device, using teensy_loader_cli.
+#               (must have teensy_loader_cli installed).
+#
+# make dfu = Download the hex file to the device, using dfu-programmer (must
+#            have dfu-programmer installed).
+#
+# make flip = Download the hex file to the device, using Atmel FLIP (must
+#             have Atmel FLIP installed).
+#
+# make dfu-ee = Download the eeprom file to the device, using dfu-programmer
+#               (must have dfu-programmer installed).
+#
+# make flip-ee = Download the eeprom file to the device, using Atmel FLIP
+#                (must have Atmel FLIP installed).
+#
+# make debug = Start either simulavr or avarice as specified for debugging,
+#              with avr-gdb or avr-insight as the front end for debugging.
+#
+# make filename.s = Just compile filename.c into the assembler code only.
+#
+# make filename.i = Create a preprocessed source file for use in submitting
+#                   bug reports to the GCC project.
+#
+# To rebuild project do "make clean" then "make all".
+#----------------------------------------------------------------------------
+
+# MCU name
+MCU = atmega32u4
+
+# Processor frequency.
+#     This will define a symbol, F_CPU, in all source code files equal to the
+#     processor frequency in Hz. You can then use this symbol in your source code to
+#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
+#     automatically to create a 32-bit value in your source code.
+#
+#     This will be an integer division of F_USB below, as it is sourced by
+#     F_USB after it has run through any CPU prescalers. Note that this value
+#     does not *change* the processor frequency - it should merely be updated to
+#     reflect the processor speed set externally so that the code can use accurate
+#     software delays.
+F_CPU = 16000000
+
+
+#
+# LUFA specific
+#
+# Target architecture (see library "Board Types" documentation).
+ARCH = AVR8
+
+# Input clock frequency.
+#     This will define a symbol, F_USB, in all source code files equal to the
+#     input clock frequency (before any prescaling is performed) in Hz. This value may
+#     differ from F_CPU if prescaling is used on the latter, and is required as the
+#     raw input clock is fed directly to the PLL sections of the AVR for high speed
+#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
+#     at the end, this will be done automatically to create a 32-bit value in your
+#     source code.
+#
+#     If no clock division is performed on the input clock inside the AVR (via the
+#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
+F_USB = $(F_CPU)
+
+# Interrupt driven control endpoint task(+60)
+OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
+
+
+# Boot Section Size in *bytes*
+#   Teensy halfKay   512
+#   Teensy++ halfKay 1024
+#   Atmel DFU loader 4096
+#   LUFA bootloader  4096
+#   USBaspLoader     2048
+OPT_DEFS += -DBOOTLOADER_SIZE=4096
+
+
+# Build Options
+#   comment out to disable the options.
+#
+BOOTMAGIC_ENABLE ?= yes	# Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE ?= no	# Mouse keys(+4700)
+EXTRAKEY_ENABLE ?= yes	# Audio control and System control(+450)
+CONSOLE_ENABLE ?= yes	# Console for debug(+400)
+COMMAND_ENABLE ?= yes    # Commands for debug and configuration
+NKRO_ENABLE ?= yes		# USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
+AUDIO_ENABLE ?= no
+RGBLIGHT_ENABLE ?= no   # Enable keyboard underlight functionality
+MIDI_ENABLE ?= no 		# MIDI controls
+UNICODE_ENABLE ?= no 		# Unicode
+BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID
\ No newline at end of file