Merge remote-tracking branch 'upstream/master'

1 files changed, 2 insertions, 87 deletions

diff --git a/keyboards/atreus/Makefile b/keyboards/atreus/Makefile
index 5894d231f9..4e2a6f00fd 100644
--- a/keyboards/atreus/Makefile
+++ b/keyboards/atreus/Makefile
@@ -1,88 +1,3 @@
-
-
-ifdef TEENSY2
-    OPT_DEFS += -DATREUS_TEENSY2
-    ATREUS_UPLOAD_COMMAND = teensy_loader_cli -w -mmcu=$(MCU) $(TARGET).hex
-else
-    OPT_DEFS += -DATREUS_ASTAR
-    OPT_DEFS += -DCATERINA_BOOTLOADER
-    ATREUS_UPLOAD_COMMAND = while [ ! -r $(USB) ]; do sleep 1; done; \
-                            avrdude -p $(MCU) -c avr109 -U flash:w:$(TARGET).hex -P $(USB)
-endif
-
-# MCU name
-#MCU = at90usb1287
-MCU = atmega32u4
-
-# Processor frequency.
-#     This will define a symbol, F_CPU, in all source code files equal to the
-#     processor frequency in Hz. You can then use this symbol in your source code to
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-#     automatically to create a 32-bit value in your source code.
-#
-#     This will be an integer division of F_USB below, as it is sourced by
-#     F_USB after it has run through any CPU prescalers. Note that this value
-#     does not *change* the processor frequency - it should merely be updated to
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
-# Boot Section Size in *bytes*
-#   Teensy halfKay   512
-#   Teensy++ halfKay 1024
-#   Atmel DFU loader 4096
-#   LUFA bootloader  4096
-#   USBaspLoader     2048
-OPT_DEFS += -DBOOTLOADER_SIZE=4096
-
-
-# Build Options
-#   comment out to disable the options.
-#
-#BOOTMAGIC_ENABLE = yes	# Virtual DIP switch configuration(+1000)
-MOUSEKEY_ENABLE ?= yes	# Mouse keys(+4700)
-EXTRAKEY_ENABLE ?= yes	# Audio control and System control(+450)
-CONSOLE_ENABLE ?= yes	# Console for debug(+400)
-COMMAND_ENABLE ?= yes    # Commands for debug and configuration
-# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
-# SLEEP_LED_ENABLE ?= yes  # Breathing sleep LED during USB suspend
-NKRO_ENABLE ?= yes		# USB Nkey Rollover - not yet supported in LUFA
-# BACKLIGHT_ENABLE ?= yes  # Enable keyboard backlight functionality
-# MIDI_ENABLE ?= YES 		# MIDI controls
-UNICODE_ENABLE ?= YES 		# Unicode
-# BLUETOOTH_ENABLE ?= yes # Enable Bluetooth with the Adafruit EZ-Key HID
-
-
-ifndef QUANTUM_DIR
+ifndef MAKEFILE_INCLUDED
 	include ../../Makefile
-endif
-
-USB ?= /dev/cu.usbmodem1411
-
-upload: build
-	$(ATREUS_UPLOAD_COMMAND)
-	
+endif
\ No newline at end of file