Merge remote-tracking branch 'upstream/master'

103 files changed, 6908 insertions, 1774 deletions

diff --git a/keyboard/hhkb/Makefile.nodebug b/keyboard/atomic/Makefile
index 578ba70c45..c4e0cb45d7 100644
--- a/keyboard/hhkb/Makefile.nodebug
+++ b/keyboard/atomic/Makefile
@@ -39,7 +39,7 @@
 #----------------------------------------------------------------------------
 
 # Target file name (without extension).
-TARGET = hhkb_lufa
+TARGET = atomic_lufa
 
 # Directory common source filess exist
 TOP_DIR = ../..
@@ -47,25 +47,22 @@ TOP_DIR = ../..
 # Directory keyboard dependent files exist
 TARGET_DIR = .
 
-
-# List C source files here. (C dependencies are automatically generated.)
-SRC +=	keymap_common.c \
+# project specific files
+SRC =	keymap_common.c \
 	matrix.c \
 	led.c
 
 ifdef KEYMAP
     SRC := keymap_$(KEYMAP).c $(SRC)
 else
-    SRC := keymap_hasu.c $(SRC)
+    SRC := keymap_vlad.c $(SRC)
 endif
 
 CONFIG_H = config.h
 
 
 # MCU name
-# PJRC Teensy++ 2.0
-#MCU = at90usb1286
-# TMK Alt Controller or PJRC Teensy 2.0
+#MCU = at90usb1287
 MCU = atmega32u4
 
 # Processor frequency.
@@ -101,14 +98,14 @@ ARCH = AVR8
 #     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
 F_USB = $(F_CPU)
 
-# Interrupt driven control endpoint task
-#OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
+# Interrupt driven control endpoint task(+60)
+OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
 
 
 # Boot Section Size in *bytes*
 #   Teensy halfKay   512
 #   Teensy++ halfKay 1024
-#   Atmel DFU loader 4096	(TMK Alt Controller)
+#   Atmel DFU loader 4096
 #   LUFA bootloader  4096
 #   USBaspLoader     2048
 OPT_DEFS += -DBOOTLOADER_SIZE=4096
@@ -117,14 +114,17 @@ OPT_DEFS += -DBOOTLOADER_SIZE=4096
 # Build Options
 #   comment out to disable the options.
 #
-BOOTMAGIC_ENABLE = yes		# Virtual DIP switch configuration
-MOUSEKEY_ENABLE = yes		# Mouse keys
-EXTRAKEY_ENABLE = yes		# Audio control and System control
-#CONSOLE_ENABLE = yes		# Console for debug
-COMMAND_ENABLE = yes    	# Commands for debug and configuration
-NKRO_ENABLE = yes		# USB Nkey Rollover
-KEYMAP_SECTION_ENABLE = yes	# fixed address keymap for keymap editor
+BOOTMAGIC_ENABLE = yes	# Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE = yes	# Mouse keys(+4700)
+EXTRAKEY_ENABLE = yes	# Audio control and System control(+450)
+CONSOLE_ENABLE = yes	# Console for debug(+400)
+COMMAND_ENABLE = yes    # Commands for debug and configuration
+#SLEEP_LED_ENABLE = yes  # Breathing sleep LED during USB suspend
+NKRO_ENABLE = yes	# USB Nkey Rollover - not yet supported in LUFA
+
 
+# Optimize size but this may cause error "relocation truncated to fit"
+#EXTRALDFLAGS = -Wl,--relax
 
 # Search Path
 VPATH += $(TARGET_DIR)
@@ -133,9 +133,3 @@ VPATH += $(TOP_DIR)
 include $(TOP_DIR)/protocol/lufa.mk
 include $(TOP_DIR)/common.mk
 include $(TOP_DIR)/rules.mk
-
-debug-on: EXTRAFLAGS += -DDEBUG -DDEBUG_ACTION
-debug-on: all
-
-debug-off: EXTRAFLAGS += -DNO_DEBUG -DNO_PRINT
-debug-off: all
diff --git a/keyboard/atomic/Makefile.pjrc b/keyboard/atomic/Makefile.pjrc
new file mode 100644
index 0000000000..9655ff65a9
--- /dev/null
+++ b/keyboard/atomic/Makefile.pjrc
@@ -0,0 +1,116 @@
+#----------------------------------------------------------------------------
+# On command line:
+#
+# make all = Make software.
+#
+# make clean = Clean out built project files.
+#
+# make coff = Convert ELF to AVR COFF.
+#
+# make extcoff = Convert ELF to AVR Extended COFF.
+#
+# make program = Download the hex file to the device.
+#                Please customize your programmer settings(PROGRAM_CMD)
+#
+# make teensy = Download the hex file to the device, using teensy_loader_cli.
+#               (must have teensy_loader_cli installed).
+#
+# make dfu = Download the hex file to the device, using dfu-programmer (must
+#            have dfu-programmer installed).
+#
+# make flip = Download the hex file to the device, using Atmel FLIP (must
+#             have Atmel FLIP installed).
+#
+# make dfu-ee = Download the eeprom file to the device, using dfu-programmer
+#               (must have dfu-programmer installed).
+#
+# make flip-ee = Download the eeprom file to the device, using Atmel FLIP
+#                (must have Atmel FLIP installed).
+#
+# make debug = Start either simulavr or avarice as specified for debugging, 
+#              with avr-gdb or avr-insight as the front end for debugging.
+#
+# make filename.s = Just compile filename.c into the assembler code only.
+#
+# make filename.i = Create a preprocessed source file for use in submitting
+#                   bug reports to the GCC project.
+#
+# To rebuild project do "make clean" then "make all".
+#----------------------------------------------------------------------------
+
+# Target file name (without extension).
+TARGET = gh60_pjrc
+
+# Directory common source filess exist
+TOP_DIR = ../..
+
+# Directory keyboard dependent files exist
+TARGET_DIR = .
+
+# project specific files
+SRC =	keymap_common.c \
+	matrix.c \
+	led.c
+
+ifdef KEYMAP
+    SRC := keymap_$(KEYMAP).c $(SRC)
+else
+    SRC := keymap_poker.c $(SRC)
+endif
+
+CONFIG_H = config.h
+
+
+# MCU name, you MUST set this to match the board you are using
+# type "make clean" after changing this, so all files will be rebuilt
+MCU = atmega32u4
+#MCU = at90usb1286
+
+
+# Processor frequency.
+#   Normally the first thing your program should do is set the clock prescaler,
+#   so your program will run at the correct speed.  You should also set this
+#   variable to same clock speed.  The _delay_ms() macro uses this, and many
+#   examples use this variable to calculate timings.  Do not add a "UL" here.
+F_CPU = 16000000
+
+
+# Boot Section Size in *bytes*
+#   Teensy halfKay   512
+#   Atmel DFU loader 4096
+#   LUFA bootloader  4096
+OPT_DEFS += -DBOOTLOADER_SIZE=4096
+
+
+# Build Options
+#   comment out to disable the options.
+#
+BOOTMAGIC_ENABLE = yes	# Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE = yes	# Mouse keys(+5000)
+EXTRAKEY_ENABLE = yes	# Audio control and System control(+600)
+CONSOLE_ENABLE = yes    # Console for debug
+COMMAND_ENABLE = yes    # Commands for debug and configuration
+SLEEP_LED_ENABLE = yes  # Breathing sleep LED during USB suspend
+NKRO_ENABLE = yes	# USB Nkey Rollover(+500)
+#PS2_MOUSE_ENABLE = yes	# PS/2 mouse(TrackPoint) support
+
+
+# Search Path
+VPATH += $(TARGET_DIR)
+VPATH += $(TOP_DIR)
+
+include $(TOP_DIR)/protocol/pjrc.mk
+include $(TOP_DIR)/common.mk
+include $(TOP_DIR)/rules.mk
+
+plain: OPT_DEFS += -DKEYMAP_PLAIN
+plain: all
+
+poker: OPT_DEFS += -DKEYMAP_POKER
+poker: all
+
+poker_set: OPT_DEFS += -DKEYMAP_POKER_SET
+poker_set: all
+
+poker_bit: OPT_DEFS += -DKEYMAP_POKER_BIT
+poker_bit: all
diff --git a/keyboard/atomic/README 2.md b/keyboard/atomic/README 2.md
new file mode 100644
index 0000000000..510cb5c8b6
--- /dev/null
+++ b/keyboard/atomic/README 2.md
@@ -0,0 +1,141 @@
+GH60 keyboard firmware
+======================
+DIY compact keyboard designed and run by komar007 and Geekhack community.
+
+- Both Rev.A and Rev.B PCB are supported by one firmware binary(issue #64)
+
+## GH60 Resources
+- [KOMAR's project page](http://blog.komar.be/projects/gh60-programmable-keyboard/)
+- [Prototyping](http://geekhack.org/index.php?topic=34959.0)
+- [Rev.A PCB test](http://geekhack.org/index.php?topic=37570.0)
+- [Rev.B PCB test](http://geekhack.org/index.php?topic=50685.0)
+- [Group buy](http://geekhack.org/index.php?topic=41464.0)
+
+
+## Build
+Move to this directory then just run `make` like:
+
+    $ make
+
+Use `make -f Makefile.pjrc` if you want to use PJRC stack but I find no reason to do so now.
+
+
+## Keymap
+Several version of keymap are available in advance but you are recommended to define your favorite layout yourself. To define your own keymap create file named `key