Add support for the KC60 v2.0 2015-09-12 (#360)

* Don't save the ctags file in the repo.

* Initial support for the KC60 board. Only 5x5 working so far.

* Rename because this isn't the same KC60 as others.

* Add in some generic layout.
Pins seem to be in the right order except the 6th column spews
gibberish.

* Don't need this for now.

* Move this to some other folder.

* Trying again to start over.

* Don't need to start over because I figured out why the 'broken' stuff wasn't working.

* Attempt to enable backlighting. It's on on pin B7 like other boards.

* Fix last port changes and fix LED control in keymap.

* Trying some other LED code.

* Bootloader needs to be bigger. Disabling backlight for now.

* Simplify LED code while I try to figure it out.

* Turn back on backlighting.

* Backlighting works now. Just need to get levels or breathing working.

* Trying to allow for turning off the LEDs before I get to brightness levels.

* The missing link: need to run the init_ports function for LEDs to work properly.

* Removing breathing stuff since it bricks the board.

* Clean up default layer.

* Cleanup keymap, KC60 doesn't support a 5th right bottom-row button.

7 files changed, 515 insertions, 0 deletions

diff --git a/keyboard/kc60_v2/Makefile b/keyboard/kc60_v2/Makefile
new file mode 100644
index 0000000000..33ece31647
--- /dev/null
+++ b/keyboard/kc60_v2/Makefile
@@ -0,0 +1,158 @@
+#----------------------------------------------------------------------------
+# On command line:
+#
+# make all = Make software.
+#
+# make clean = Clean out built project files.
+#
+# make coff = Convert ELF to AVR COFF.
+#
+# make extcoff = Convert ELF to AVR Extended COFF.
+#
+# make program = Download the hex file to the device.
+#                Please customize your programmer settings(PROGRAM_CMD)
+#
+# make teensy = Download the hex file to the device, using teensy_loader_cli.
+#               (must have teensy_loader_cli installed).
+#
+# make dfu = Download the hex file to the device, using dfu-programmer (must
+#            have dfu-programmer installed).
+#
+# make flip = Download the hex file to the device, using Atmel FLIP (must
+#             have Atmel FLIP installed).
+#
+# make dfu-ee = Download the eeprom file to the device, using dfu-programmer
+#               (must have dfu-programmer installed).
+#
+# make flip-ee = Download the eeprom file to the device, using Atmel FLIP
+#                (must have Atmel FLIP installed).
+#
+# make debug = Start either simulavr or avarice as specified for debugging, 
+#              with avr-gdb or avr-insight as the front end for debugging.
+#
+# make filename.s = Just compile filename.c into the assembler code only.
+#
+# make filename.i = Create a preprocessed source file for use in submitting
+#                   bug reports to the GCC project.
+#
+# To rebuild project do "make clean" then "make all".
+#----------------------------------------------------------------------------
+
+# Target file name (without extension).
+TARGET = kc60
+
+
+# Directory common source filess exist
+TOP_DIR = ../..
+TMK_DIR = ../../tmk_core
+
+# Directory keyboard dependent files exist
+TARGET_DIR = .
+
+# # project specific files
+SRC = kc60.c
+
+ifdef KEYMAP
+    SRC := keymaps/$(KEYMAP).c $(SRC)
+else
+    SRC := keymaps/default.c $(SRC)
+endif
+
+CONFIG_H = config.h
+
+# MCU name
+#MCU = at90usb1287
+MCU = atmega32u4
+
+# Processor frequency.
+#     This will define a symbol, F_CPU, in all source code files equal to the
+#     processor frequency in Hz. You can then use this symbol in your source code to
+#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
+#     automatically to create a 32-bit value in your source code.
+#
+#     This will be an integer division of F_USB below, as it is sourced by
+#     F_USB after it has run through any CPU prescalers. Note that this value
+#     does not *change* the processor frequency - it should merely be updated to
+#     reflect the processor speed set externally so that the code can use accurate
+#     software delays.
+F_CPU = 16000000
+
+
+#
+# LUFA specific
+#
+# Target architecture (see library "Board Types" documentation).
+ARCH = AVR8
+
+# Input clock frequency.
+#     This will define a symbol, F_USB, in all source code files equal to the
+#     input clock frequency (before any prescaling is performed) in Hz. This value may
+#     differ from F_CPU if prescaling is used on the latter, and is required as the
+#     raw input clock is fed directly to the PLL sections of the AVR for high speed
+#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
+#     at the end, this will be done automatically to create a 32-bit value in your
+#     source code.
+#
+#     If no clock division is performed on the input clock inside the AVR (via the
+#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
+F_USB = $(F_CPU)
+
+# Interrupt driven control endpoint task(+60)
+OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
+
+
+# Boot Section Size in *bytes*
+#   Teensy halfKay   512
+#   Teensy++ halfKay 1024
+#   Atmel DFU loader 4096
+#   LUFA bootloader  4096
+#   USBaspLoader     2048
+OPT_DEFS += -DBOOTLOADER_SIZE=4096
+
+
+# Build Options
+#   change yes to no to disable
+#
+BOOTMAGIC_ENABLE = yes      # Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE = yes       # Mouse keys(+4700)
+EXTRAKEY_ENABLE = yes       # Audio control and System control(+450)
+CONSOLE_ENABLE = yes        # Console for debug(+400)
+COMMAND_ENABLE = yes        # Commands for debug and configuration
+KEYBOARD_LOCK_ENABLE = yes  # Allow locking of keyboard via magic key
+# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
+SLEEP_LED_ENABLE = no       # Breathing sleep LED during USB suspend
+# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
+NKRO_ENABLE = no            # USB Nkey Rollover
+BACKLIGHT_ENABLE = yes      # Enable keyboard backlight functionality
+MIDI_ENABLE = no            # MIDI controls
+UNICODE_ENABLE = no         # Unicode
+BLUETOOTH_ENABLE = no       # Enable Bluetooth with the Adafruit EZ-Key HID
+AUDIO_ENABLE = no           # Audio output on port C6
+
+
+ifdef KEYMAP
+
+ifeq ("$(wildcard keymaps/$(KEYMAP).c)","")
+ifneq ("$(wildcard keymaps/$(KEYMAP)/makefile.mk)","")
+    include keymaps/$(KEYMAP)/makefile.mk
+endif 
+endif
+
+else
+
+ifneq ("$(wildcard keymaps/default/makefile.mk)","")
+    include keymaps/default/makefile.mk
+endif
+
+endif
+
+# Optimize size but this may cause error "relocation truncated to fit"
+#EXTRALDFLAGS = -Wl,--relax
+
+# Search Path
+VPATH += $(TARGET_DIR)
+VPATH += $(TOP_DIR)
+VPATH += $(TMK_DIR)
+
+include $(TOP_DIR)/quantum/quantum.mk
+
diff --git a/keyboard/kc60_v2/README.md b/keyboard/kc60_v2/README.md
new file mode 100644
index 0000000000..4be448d15c
--- /dev/null
+++ b/keyboard/kc60_v2/README.md
@@ -0,0 +1,24 @@
+kc60 keyboard firmware
+======================
+
+## Quantum MK Firmware
+
+For the full Quantum feature list, see [the parent README.md](/README.md).
+
+## Building
+
+Download or clone the whole firmware and navigate to the keyboard/kc60 folder. Once your dev env is setup, you'll be able to type `make` to generate your .hex - you can then use the Teensy Loader to program your .hex file. 
+
+Depending on which keymap you would like to use, you will have to compile slightly differently.
+
+### Default
+To build with the default keymap, simply run `make`.
+
+### Other Keymaps
+Several version of keymap are available in advance but you are recommended to define your favorite layout yourself. To define your own keymap create file named `<name>.c` in the keymaps folder, and see keymap document (you can find in top README.md) and existent keymap files.
+
+To build the firmware binary hex file with a keymap just do `make` with `KEYMAP` option like:
+```
+$ make KEYMAP=[default|jack|<name>]
+```
+Keymaps follow the format **__\<name\>.c__** and are stored in the `keymaps` folder.
diff --git a/keyboard/kc60_v2/config.h b/keyboard/kc60_v2/config.h
new file mode 100644
index 0000000000..16bc1cbb29
--- /dev/null
+++ b/keyboard/kc60_v2/config.h
@@ -0,0 +1,161 @@
+/*
+Copyright 2012 Jun Wako <wakojun@gmail.com>
+
+This program is free software: you can redistribute it and/or modify
+it under the terms of the GNU General Public License as published by
+the Free Software Foundation, either version 2 of the License, or
+(at your option) any later version.
+
+This program is distributed in the hope that it will be useful,
+but WITHOUT ANY WARRANTY; without even the implied warranty of
+MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+GNU General Public License for more details.
+
+You should have received a copy of the GNU General Public License
+along with this program.  If not, see <http://www.gnu.org/licenses/>.
+*/
+
+#ifndef CONFIG_H
+#define CONFIG_H
+
+#include "config_common.h"
+
+/* USB Device descriptor parameter */
+#define VENDOR_ID       0xFEED
+#define PRODUCT_ID      0x6060
+#define DEVICE_VER      0x0001
+#define MANUFACTURER    You
+#define PRODUCT         kc60v2
+#define DESCRIPTION     A custom keyboard
+
+/* key matrix size */
+#define MATRIX_ROWS 5
+#define MATRIX_COLS 14
+
+/*
+ * Keyboard Matrix Assignments
+ *
+ * Change this to how you wired your keyboard
+ * COLS: AVR pins used for columns, left to right
+ * ROWS: AVR pins used for rows, top to bottom
+ * DIODE_DIRECTION: COL2ROW = COL = Anode (+), ROW = Cathode (-, marked on diode)
+ *                  ROW2COL = ROW = Anode (+), COL = Cathode (-, marked on diode)
+ *
+*/
+
+// Possible pins for columns include: F1  F0  E6  D7  D6  D4  C7  C6  B7  B5  B4  B3  B1  B0
+// Pins for rows include:  D0  D1  F6  F7  D5
+#define MATRIX_ROW_PINS { D0, D1, F6, F7, D5 }
+#define MATRIX_COL_PINS { F0, F1, E6, C7, C6, B7, D4, B1, B0, B5, B4, D7, D6, B3 }
+#define UNUSED_PINS
+
+/* COL2ROW or ROW2COL */
+#define DIODE_DIRECTION COL2ROW
+
+/* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */
+#define DEBOUNCING_DELAY 5
+
+/* define if matrix has ghost (lacks anti-ghosting diodes) */
+//#define MATRIX_HAS_GHOST
+
+/* number of backlight levels */
+#define BACKLIGHT_LEVELS 3
+
+/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */
+#define LOCKING_SUPPORT_ENABLE
+/* Locking resynchronize hack */
+#define LOCKING_RESYNC_ENABLE
+
+/*
+ * Force NKRO
+ *
+ * Force NKRO (nKey Rollover) to be enabled by default, regardless of the saved
+ * state in the bootmagic EEPROM settings. (Note that NKRO must be enabled in the
+ * makefile for this to work.)
+ *
+ * If forced on, NKRO can be disabled via magic key (default = LShift+RShift+N)
+ * until the next keyboard reset.
+ *
+ * NKRO may prevent your keystrokes from being detected in the BIOS, but it is
+ * fully operational during normal computer usage.
+ *
+ * For a less heavy-handed approach, enable NKRO via magic key (LShift+RShift+N)
+ * or via bootmagic (hold SPACE+N while plugging in the keyboard). Once set by
+ * bootmagic, NKRO mode will always be enabled until it is toggled again during a
+ * power-up.
+ *
+ */
+//#define FORCE_NKRO
+
+/*
+ * Magic Key Options
+ *
+ * Magic keys are hotkey commands that allow control over firmware functions of
+ * the keyboard. They are best used in combination with the HID Listen program,
+ * found here: https://www.pjrc.com/teensy/hid_listen.html
+ *
+ * The options below allow the magic key functionality to be changed. This is
+ * useful if your keyboard/keypad is missing keys and you want magic key support.
+ *
+ */
+
+/* key combination for magic key command */
+#define IS_COMMAND() ( \
+    keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)) \
+)
+
+/* control how magic key switches layers */
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS  true
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS  true
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM false
+
+/* override magic key keymap */
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM
+//#define MAGIC_KEY_HELP1          H
+//#define MAGIC_KEY_HELP2          SLASH
+//#define MAGIC_KEY_DEBUG          D
+//#define MAGIC_KEY_DEBUG_MATRIX   X
+//#define MAGIC_KEY_DEBUG_KBD      K
+//#define MAGIC_KEY_DEBUG_MOUSE    M
+//#define MAGIC_KEY_VERSION        V
+//#define MAGIC_KEY_STATUS         S
+//#define MAGIC_KEY_CONSOLE        C
+//#define MAGIC_KEY_LAYER0_ALT1    ESC
+//#define MAGIC_KEY_LAYER0_ALT2    GRAVE
+//#define MAGIC_KEY_LAYER0         0
+//#define MAGIC_KEY_LAYER1         1
+//#define MAGIC_KEY_LAYER2         2
+//#define MAGIC_KEY_LAYER3         3
+//#define MAGIC_KEY_LAYER4         4
+//#define MAGIC_KEY_LAYER5         5
+//#define MAGIC_KEY_LAYER6         6
+//#define MAGIC_KEY_LAYER7         7
+//#define MAGIC_KEY_LAYER8         8
+//#define MAGIC_KEY_LAYER9         9
+//#define MAGIC_KEY_BOOTLOADER     PAUSE
+//#define MAGIC_KEY_LOCK           CAPS
+//#define MAGIC_KEY_EEPROM         E
+//#define MAGIC_KEY_NKRO           N
+//#define MAGIC_KEY_SLEEP_LED      Z
+
+/*
+ * Feature disable options
+ *  These options are also useful to firmware size reduction.
+ */
+
+/* disable debug print */
+//#define NO_DEBUG
+
+/* disable print */
+//#define NO_PRINT
+
+/* disable action features */
+//#define NO_ACTION_LAYER
+//#define NO_ACTION_TAPPING
+//#define NO_ACTION_ONESHOT
+//#define NO_ACTION_MACRO
+//#define NO_ACTION_FUNCTION
+
+#endif
diff --git a/keyboard/kc60_v2/kc60.c b/keyboard/kc60_v2/kc60.c
new file mode 100644
index 0000000000..0a578b2b88
--- /dev/null
+++ b/keyboard/kc60_v2/kc60.c
@@ -0,0 +1,111 @@
+#include "kc60.h"
+
+__attribute__ ((weak))
+  void matrix_init_user(void) {
+    // leave this function blank - it can be defined in a keymap file
+  };
+
+__attribute__ ((weak))
+  void matrix_scan_user(void) {
+    // leave this function blank - it can be defined in a keymap file
+  }
+
+__attribute__ ((weak))
+  bool process_action_user(keyrecord_t *record) {
+    // leave this function blank - it can be defined in a keymap file
+    return true;
+  }
+
+__attribute__ ((weak))
+  void led_set_user(uint8_t usb_led) {
+    // leave this function blank - it can be defined in a keymap file
+  }
+
+void matrix_init_kb(void) {
+  // put your keyboard start-up code here
+  // runs once when the firmware starts up
+
+#ifdef BACKLIGHT_ENABLE
+  backlight_init_ports();
+#endif
+
+  matrix_init_user();
+}
+
+void matrix_scan_kb(void) {
+  // put your looping keyboard code here
+  // runs every cycle (a lot)
+
+  matrix_scan_user();
+}
+
+bool process_action_kb(keyrecord_t *record) {
+  // put your per-action keyboard code here
+  // runs for every action, just before processing by the firmware
+
+  return process_action_user(record);
+}
+
+void led_set_kb(uint8_t usb_led) {
+  // put your keyboard LED indicator (ex: Caps Lock LED) toggling code here
+
+  led_set_user(usb_led);
+}
+
+#ifdef BACKLIGHT_ENABLE
+#define CHANNEL OCR1B
+
+void backlight_init_ports()
+{
+
+  // Setup PB6 as output and output low.
+  DDRB |= (1<<6);
+  PORTB &= ~(1<<6);
+
+  // Use full 16-bit resolution. 
+  ICR1 = 0xFFFF;
+
+  // I could write a wall of text here to explain... but TL;DW
+  // Go read the ATmega32u4 datasheet.
+  // And this: http://blog.saikoled.com/post/43165849837/secret-konami-cheat-code-to-high-resolution-pwm-on
+
+  // Pin PB7 = OCR1C (Timer 1, Channel C)
+  // Compare Output Mode = Clear on compare match, Channel C = COM1B1=1 COM1C0=0
+  // (i.e. start high, go low when counter matches.)
+  // WGM Mode 14 (Fast PWM) = WGM13=1 WGM12=1 WGM11=1 WGM10=0
+  // Clock Select = clk/1 (no prescaling) = CS12=0 CS11=0 CS10=1
+
+  TCCR1A = _BV(COM1B1) | _BV(WGM11); // = 0b00001010;
+  TCCR1B = _BV(WGM13) | _BV(WGM12) | _BV(CS10); // = 0b00011001;
+
+  backlight_init();
+}
+
+void backlight_set(uint8_t level)
+{
+  // Prevent backlight blink on lowest level
+  PORTB &= ~(_BV(PORTB6));
+
+  if ( level == 0 )
+  {
+    // Turn off PWM control on PB6, revert to output low.
+    TCCR1A &= ~(_BV(COM1B1));
+    CHANNEL = 0x0;
+  }
+  else if ( level == BACKLIGHT_LEVELS)
+  {
+    // Turn on PWM control of PB6
+    TCCR1A |= _BV(COM1B1);
+    // Set the brightness
+    CHANNEL = 0xFFFF;
+  }
+  else        
+  {
+    // Turn on PWM control of PB6
+    TCCR1A |= _BV(COM1B1);
+    // Set the brightness
+    CHANNEL = 0xFFFF >> ((BACKLIGHT_LEVELS - level) * ((BACKLIGHT_LEVELS + 1) / 2));
+  }
+}
+
+#endif
diff --git a/keyboard/kc60_v2/kc60.h b/keyboard/kc60_v2/kc60.h
new file mode 100644
index 0000000000..d346a55028
--- /dev/null
+++ b/keyboard/kc60_v2/kc60.h
@@ -0,0 +1,36 @@
+#ifndef KC60_H
+#define KC60_H
+
+#include "matrix.h"
+#include "keymap_common.h"
+#ifdef BACKLIGHT_ENABLE
+#include "backlight.h"
+#endif
+#include <avr/io.h>
+#include <stddef.h>
+
+// This a shortcut to help you visually see your layout.
+// The first section contains all of the arguements
+// The second converts the arguments into a multi-dimensional array
+#define KEYMAP( \
+    K00, K01, K02, K03, K04, K05, K06, K07, K08, K09, K0A, K0B, K0C, K0D, \
+    K10, K11, K12, K13, K14, K15, K16, K17, K18, K19, K1A, K1B, K1C, K1D, \
+    K20, K21, K22, K23, K24, K25, K26, K27, K28, K29, K2A, K2B, K2C, K2D, \
+    K30, K31, K32, K33, K34, K35, K36, K37, K38, K39, K3A, K3B, K3C, K3D, \
+    K40, K41, K42,           K45,                     K4A, K4B, K4C, K4D  \
+    ) { \
+  {  K00,  K01,  K02,  K03,    K04,    K05,  K06,    K07,    K08,    K09,  K0A,  K0B,  K0C,  K0D  },  \
+  {  K10,  K11,  K12,  K13,    K14,    K15,  K16,    K17,    K18,    K19,  K1A,  K1B,  K1C,  K1D  },  \
+  {  K20,  K21,  K22,  K23,    K24,    K25,  K26,    K27,    K28,    K29,  K2A,  K2B,  K2C,  K2D  },  \
+  {  K30,  K31,  K32,  K33,    K34,    K35,  K36,    K37,    K38,    K39,  K3A,  K3B,  K3C,  K3D  },  \
+  {  K40,  K41,  K42,  KC_NO,  KC_NO,  K45,  KC_NO,  KC_NO,  KC_NO,  KC_NO,K4A,  K4B,  K4C,  K4D  }   \
+}
+
+void matrix_init_user(void);
+void matrix_scan_user(void);
+bool process_action_user(keyrecord_t *record);
+
+void led_set_user(uint8_t usb_led);
+void backlight_init_ports(void);
+
+#endif
diff --git a/keyboard/kc60_v2/keymaps/default.c b/keyboard/kc60_v2/keymaps/default.c
new file mode 100644
index 0000000000..6f8352c695
--- /dev/null
+++ b/keyboard/kc60_v2/keymaps/default.c
@@ -0,0 +1,24 @@
+// This is the canonical layout file for the Quantum project. If you want to add another keyboard,
+// this is the style you want to emulate.
+
+#include "kc60.h"
+
+const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
+  [0] = KEYMAP( /* Basic QWERTY */
+      KC_ESC,   KC_1,     KC_2,     KC_3,    KC_4,     KC_5,     KC_6,     KC_7,    KC_8,  KC_9,     KC_0,     KC_MINS,  KC_EQL,   KC_BSPC,  \
+      KC_TAB,   KC_Q,     KC_W,     KC_E,    KC_R,     KC_T,     KC_Y,     KC_U,    KC_I,  KC_O,     KC_P,     KC_LBRC,  KC_RBRC,  KC_BSLS,  \
+      KC_CAPS,  KC_A,     KC_S,     KC_D,    KC_F,     KC_G,     KC_H,     KC_J,    KC_K,  KC_L,     KC_SCLN,  KC_QUOT,  KC_NO,    KC_ENT,   \
+      KC_LSFT,  KC_NO,    KC_Z,     KC_X,    KC_C,     KC_V,     KC_B,     KC_N,    KC_M,  KC_COMM,  KC_DOT,   KC_SLSH,  KC_NO,    KC_RSFT,  \
+      KC_LCTL,  KC_LALT,  KC_LGUI,                     KC_SPC,                                       KC_RGUI,  KC_RALT,  KC_RCTL,  RESET \
+      ),
+};
+
+const uint16_t PROGMEM fn_actions[] = {
+
+};
+
+const macro_t *action_get_macro(keyrecord_t *record, uint8_t id, uint8_t opt)
+{
+  // MACRODOWN only works in this function
+  return MACRO_NONE;
+};
diff --git a/keyboard/planck/.gitignore b/keyboard/planck/.gitignore
new file mode 100644
index 0000000000..6e92f57d46
--- /dev/null
+++ b/keyboard/planck/.gitignore
@@ -0,0 +1 @@
+tags