[Jack & Erez] Comments + tiny updates and cleanup

15 files changed, 0 insertions, 2987 deletions

diff --git a/keyboard/ergodox/Makefile b/keyboard/ergodox/Makefile
deleted file mode 100644
index f71d096783..0000000000
--- a/keyboard/ergodox/Makefile
+++ /dev/null
@@ -1,139 +0,0 @@
-#----------------------------------------------------------------------------
-# On command line:
-#
-# make all = Make software.
-#
-# make clean = Clean out built project files.
-#
-# make coff = Convert ELF to AVR COFF.
-#
-# make extcoff = Convert ELF to AVR Extended COFF.
-#
-# make program = Download the hex file to the device.
-#                Please customize your programmer settings(PROGRAM_CMD)
-#
-# make teensy = Download the hex file to the device, using teensy_loader_cli.
-#               (must have teensy_loader_cli installed).
-#
-# make dfu = Download the hex file to the device, using dfu-programmer (must
-#            have dfu-programmer installed).
-#
-# make flip = Download the hex file to the device, using Atmel FLIP (must
-#             have Atmel FLIP installed).
-#
-# make dfu-ee = Download the eeprom file to the device, using dfu-programmer
-#               (must have dfu-programmer installed).
-#
-# make flip-ee = Download the eeprom file to the device, using Atmel FLIP
-#                (must have Atmel FLIP installed).
-#
-# make debug = Start either simulavr or avarice as specified for debugging, 
-#              with avr-gdb or avr-insight as the front end for debugging.
-#
-# make filename.s = Just compile filename.c into the assembler code only.
-#
-# make filename.i = Create a preprocessed source file for use in submitting
-#                   bug reports to the GCC project.
-#
-# To rebuild project do "make clean" then "make all".
-#----------------------------------------------------------------------------
-
-# Target file name (without extension).
-TARGET = ergodox
-
-
-# Directory common source filess exist
-TOP_DIR = ../..
-
-# Directory keyboard dependent files exist
-TARGET_DIR = .
-
-# # project specific files
-SRC = ergodox.c \
-	twimaster.c \
-	backlight.c 
-
-ifdef KEYMAP
-    SRC := keymaps/keymap_$(KEYMAP).c $(SRC)
-else
-    SRC := keymaps/keymap_default.c $(SRC)
-endif
-
-CONFIG_H = config.h
-
-# MCU name
-#MCU = at90usb1287
-MCU = atmega32u4
-
-# Processor frequency.
-#     This will define a symbol, F_CPU, in all source code files equal to the
-#     processor frequency in Hz. You can then use this symbol in your source code to
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-#     automatically to create a 32-bit value in your source code.
-#
-#     This will be an integer division of F_USB below, as it is sourced by
-#     F_USB after it has run through any CPU prescalers. Note that this value
-#     does not *change* the processor frequency - it should merely be updated to
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
-# Boot Section Size in *bytes*
-#   Teensy halfKay   512
-#   Teensy++ halfKay 1024
-#   Atmel DFU loader 4096
-#   LUFA bootloader  4096
-#   USBaspLoader     2048
-OPT_DEFS += -DBOOTLOADER_SIZE=4096
-
-
-# Build Options
-#   comment out to disable the options.
-#
-BOOTMAGIC_ENABLE = yes	# Virtual DIP switch configuration(+1000)
-MOUSEKEY_ENABLE = yes	# Mouse keys(+4700)
-EXTRAKEY_ENABLE = yes	# Audio control and System control(+450)
-CONSOLE_ENABLE = yes	# Console for debug(+400)
-COMMAND_ENABLE = yes    # Commands for debug and configuration
-# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
-# SLEEP_LED_ENABLE = yes  # Breathing sleep LED during USB suspend
-# NKRO_ENABLE = yes		# USB Nkey Rollover - not yet supported in LUFA
-# BACKLIGHT_ENABLE = yes  # Enable keyboard backlight functionality
-# MIDI_ENABLE = YES 		# MIDI controls
-# UNICODE_ENABLE = YES 		# Unicode
-# BLUETOOTH_ENABLE = yes # Enable Bluetooth with the Adafruit EZ-Key HID
-
-
-# Optimize size but this may cause error "relocation truncated to fit"
-#EXTRALDFLAGS = -Wl,--relax
-
-# Search Path
-VPATH += $(TARGET_DIR)
-VPATH += $(TOP_DIR)
-
-include $(TOP_DIR)/quantum.mk
-
diff --git a/keyboard/ergodox/README.md b/keyboard/ergodox/README.md
deleted file mode 100644
index bbbc73515b..0000000000
--- a/keyboard/ergodox/README.md
+++ /dev/null
@@ -1,56 +0,0 @@
-# TMK Generic
-
-* I'm not sure what the Magic + H does.
- Is this a menu that will pop up regardless of what platform and program is open? 
-
- Yes, this is sort of debugging.
- Use PJRC's [hid_listen](https://www.pjrc.com/teensy/hid_listen.html) to see debug messages.
-
-# TMK/Ergodox specific
-
-* I would like to configure my leds to indicate the active layer.
- I read that can be done, but I haven't seen an example for this firmware.
- Can someone please post an example or a link?
-
- TMK for Ergodox have support for seven (!) led's:
- - three on right
- - three on left (see http://geekhack.org/index.php?topic=22780.msg873819#msg873819 for more details)
- - Teensy onboard led as well
-
- Any of these leds can be used as layer indicator or NumLock/CapsLock/ScrollLock led.
-
- [Here is example](https://github.com/cub-uanic/tmk_keyboard/blob/cub_layout/keyboard/ergodox/matrix.c#L121-167)
- how you can assign some meaning to each led.
- In this code only left leds are used to show layers, but you can
- [change `led_set()`](https://github.com/cub-uanic/tmk_keyboard/blob/cub_layout/keyboard/ergodox/led.c)
- and do anything you want with all leds.
-
-# Firmware
-
-Q: Where to get binaries?
-A:
-
-Q: Where to get sources?
-A:
-
-Q: How to compile?
-A:
-
-
-# Layouts
-
-description of layouts in base firmware binaries
-
-
-# Things TO-DO
-
-- [ ] Flash NumLock led only when "numpad" layer is active
-- [ ] Command (in terms of IS_COMMAND) to switch to no-leds mode
-- [ ] Increase count of ACTION keys
-- [ ] Fix command_state() onboard led: it should flash only when kbd in some specific mode (CONSOLE || MOUSE)
-- [ ] ergodox_blink_all_leds() should save current state of leds, and restore after blink. initial state of all leds == off
-- [ ] add support for pseudo-backlight (reversed LEDs) + docs/photo
-- [ ] command to debug all LEDs (on/off/blink)
-- [ ] proper (in-core) implementation of DEBUG_MATRIX_SCAN_RATE (non-Ergodox specific)
-- [ ] proper (in-core) support for per-layer fn_actions[]
-
diff --git a/keyboard/ergodox/backlight.c b/keyboard/ergodox/backlight.c
deleted file mode 100644
index f69364b2af..0000000000
--- a/keyboard/ergodox/backlight.c
+++ /dev/null
@@ -1,61 +0,0 @@
-
-#include <avr/io.h>
-#include "backlight.h"
-
-#define CHANNEL OCR1C
-
-void backlight_init_ports()
-{
-
-    // Setup PB7 as output and output low.
-    DDRB |= (1<<7);
-    PORTB &= ~(1<<7);
-    
-    // Use full 16-bit resolution. 
-    ICR1 = 0xFFFF;
-
-    // I could write a wall of text here to explain... but TL;DW
-    // Go read the ATmega32u4 datasheet.
-    // And this: http://blog.saikoled.com/post/43165849837/secret-konami-cheat-code-to-high-resolution-pwm-on
-    
-    // Pin PB7 = OCR1C (Timer 1, Channel C)
-    // Compare Output Mode = Clear on compare match, Channel C = COM1C1=1 COM1C0=0
-    // (i.e. start high, go low when counter matches.)
-    // WGM Mode 14 (Fast PWM) = WGM13=1 WGM12=1 WGM11=1 WGM10=0
-    // Clock Select = clk/1 (no prescaling) = CS12=0 CS11=0 CS10=1
-    
-    TCCR1A = _BV(COM1C1) | _BV(WGM11); // = 0b00001010;
-    TCCR1B = _BV(WGM13) | _BV(WGM12) | _BV(CS10); // = 0b00011001;
-
-    backlight_init();
-}
-
-void backlight_set(uint8_t level)
-{
-    if ( level == 0 )
-    {
-        // Turn off PWM control on PB7, revert to output low.
-        TCCR1A &= ~(_BV(COM1C1));
-        CHANNEL = 0x0;
-        // Prevent backlight blink on lowest level
-        PORTB &= ~(_BV(PORTB7));
-    }
-    else if ( level == BACKLIGHT_LEVELS )
-    {
-        // Prevent backlight blink on lowest level
-        PORTB &= ~(_BV(PORTB7));
-        // Turn on PWM control of PB7
-        TCCR1A |= _BV(COM1C1);
-        // Set the brightness
-        CHANNEL = 0xFFFF;
-    }
-    else        
-    {
-        // Prevent backlight blink on lowest level
-        PORTB &= ~(_BV(PORTB7));
-        // Turn on PWM control of PB7
-        TCCR1A |= _BV(COM1C1);
-        // Set the brightness
-        CHANNEL = 0xFFFF >> ((BACKLIGHT_LEVELS - level) * ((BACKLIGHT_LEVELS + 1) / 2));
-    }
-}
\ No newline at end of file
diff --git a/keyboard/ergodox/config.h b/keyboard/ergodox/config.h
deleted file mode 100644
index c8eaae6146..0000000000
--- a/keyboard/ergodox/config.h
+++ /dev/null
@@ -1,88 +0,0 @@
-/*
-Copyright 2012 Jun Wako <wakojun@gmail.com>
-Copyright 2013 Oleg Kostyuk <cub.uanic@gmail.com>
-
-This program is free software: you can redistribute it and/or modify
-it under the terms of the GNU General Public License as published by
-the Free Software Foundation, either version 2 of the License, or
-(at your option) any later version.
-
-This program is distributed in the hope that it will be useful,
-but WITHOUT ANY WARRANTY; without even the implied warranty of
-MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
-GNU General Public License for more details.
-
-You should have received a copy of the GNU General Public License
-along with this program.  If not, see <http://www.gnu.org/licenses/>.
-*/
-
-#ifndef CONFIG_H
-#define CONFIG_H
-
-#include "config_common.h"
-
-/* USB Device descriptor parameter */
-#define VENDOR_ID       0xFEED
-#define PRODUCT_ID      0x1307
-#define DEVICE_VER      0x0001
-#define MANUFACTURER    ErgoDox EZ
-#define PRODUCT         ErgoDox EZ
-#define DESCRIPTION     t.m.k. keyboard firmware for Ergodox
-
-/* key matrix size */
-#define MATRIX_ROWS 14
-#define MATRIX_COLS 6
-
-#define MOUSEKEY_DELAY          100
-#define MOUSEKEY_INTERVAL       20
-#define MOUSEKEY_MAX_SPEED      3
-#define MOUSEKEY_TIME_TO_MAX    10
-
-#define COLS (int []){ F1, F0, B0, C7, F4, F5, F6, F7, D4, D6, B4, D7 }
-#define ROWS (int []){ D0, D5, B5, B6 }
-
-/* COL2ROW or ROW2COL */
-#define DIODE_DIRECTION COL2ROW
-
-/* define if matrix has ghost */
-//#define MATRIX_HAS_GHOST
-
-/* number of backlight levels */
-#define BACKLIGHT_LEVELS 3
-
-/* Set 0 if debouncing isn't needed */
-#define DEBOUNCE    2
-#define TAPPING_TERM    230
-#define TAPPING_TOGGLE  2
-
-/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */
-#define LOCKING_SUPPORT_ENABLE
-/* Locking resynchronize hack */
-#define LOCKING_RESYNC_ENABLE
-
-/* key combination for command */
-#define IS_COMMAND() ( \
-    keyboard_report->mods == (MOD_BIT(KC_LCTL) | MOD_BIT(KC_RCTL)) || \
-    keyboard_report->mods == (MOD_BIT(KC_LSFT) | MOD_BIT(KC_RSFT)) \
-)
-
-/*
- * Feature disable options
- *  These options are also useful to firmware size reduction.
- */
-
-/* disable debug print */
-// #define NO_DEBUG
-
-/* disable print */
-// #define NO_PRINT
-
-/* disable action features */
-//#define NO_ACTION_LAYER
-//#define NO_ACTION_TAPPING
-//#define NO_ACTION_ONESHOT
-//#define NO_ACTION_MACRO
-//#define NO_ACTION_FUNCTION
-//#define DEBUG_MATRIX_SCAN_RATE
-
-#endif
diff --git a/keyboard/ergodox/ergodox.c b/keyboard/ergodox/ergodox.c
deleted file mode 100644
index 950e6a66ca..0000000000
--- a/keyboard/ergodox/ergodox.c
+++ /dev/null
@@ -1,123 +0,0 @@
-#include "ergodox.h"
-#include "i2cmaster.h"
-
-bool i2c_initialized = 0;
-uint8_t mcp23018_status = 0x20;
-
-bool ergodox_left_led_1 = 0;  // left top
-bool ergodox_left_led_2 = 0;  // left middle
-bool ergodox_left_led_3 = 0;  // left bottom
-
-__attribute__ ((weak))
-void * matrix_init_user(void) {
-
-};
-
-__attribute__ ((weak))
-void * matrix_scan_user(void) {
-
-};
-
-void * matrix_init_kb(void) {
-   // keyboard LEDs (see "PWM on ports OC1(A|B|C)" in "teensy-2-0.md")
-    TCCR1A = 0b10101001;  // set and configure fast PWM
-    TCCR1B = 0b00001001;  // set and configure fast PWM
-
-    // (tied to Vcc for hardware convenience)
-    DDRB  &= ~(1<<4);  // set B(4) as input
-    PORTB &= ~(1<<4);  // set B(4) internal pull-up disabled
-
-    // unused pins - C7, D4, D5, D7, E6
-    // set as input with internal pull-ip enabled
-    DDRC  &= ~(1<<7);
-    DDRD  &= ~(1<<7 | 1<<5 | 1<<4);
-    DDRE  &= ~(1<<6);
-    PORTC |=  (1<<7);
-    PORTD |=  (1<<7 | 1<<5 | 1<<4);
-    PORTE |=  (1<<6);
-
-    ergodox_blink_all_leds();
-
-	if (matrix_init_user) {
-		(*matrix_init_user)();
-	}
-};
-
-void * matrix_scan_kb(void) {
-
-	if (matrix_scan_user) {
-		(*matrix_scan_user)();
-	}
-};
-
-
-void ergodox_blink_all_leds(void)
-{
-    ergodox_led_all_off();
-    ergodox_led_all_set(LED_BRIGHTNESS_HI);
-    ergodox_led_all_on();
-    _delay_ms(333);
-    ergodox_led_all_off();
-}
-
-uint8_t init_mcp23018(void) {
-    mcp23018_status = 0x20;
-
-    // I2C subsystem
-    if (i2c_initialized == 0) {
-        i2c_init();  // on pins D(1,0)
-        i2c_initialized++;
-        _delay_ms(1000);
-    }
-
-    // set pin direction
-    // - unused  : input  : 1
-    // - input   : input  : 1
-    // - driving : output : 0
-    mcp23018_status = i2c_start(I2C_ADDR_WRITE);    if (mcp23018_status) goto out;
-    mcp23018_status = i2c_write(IODIRA);            if (mcp23018_status) goto out;
-    mcp23018_status = i2c_write(0b00000000);        if (mcp23018_status) goto out;
-    mcp23018_status = i2c_write(0b00111111);        if (mcp23018_status) goto out;
-    i2c_stop();
-
-    // set pull-up
-    // - unused  : on  : 1
-    // - input   : on  : 1
-    // - driving : off : 0
-    mcp23018_status = i2c_start(I2C_ADDR_WRITE);    if (mcp23018_status) goto out;
-    mcp23018_status = i2c_write(GPPUA);             if (mcp23018_status) goto out;
-    mcp23018_status = i2c_write(0b00000000);        if (mcp23018_status) goto out;
-    mcp23018_status = i2c_write(0b00111111);        if (mcp23018_status) goto out;
-
-out:
-    i2c_stop();
-
-    if (!mcp23018_status) mcp23018_status = ergodox_left_leds_update();
-
-    return mcp23018_status;
-}
-
-uint8_t ergodox_left_leds_update(void) {
-    if (mcp23018_status) { // if there was an error
-        return mcp23018_status;
-    }
-
-    // set logical value (doesn't matter on inputs)
-    // - unused  : hi-Z : 1
-    // - input   : hi-Z : 1
-    // - driving : hi-Z : 1
-    mcp23018_status = i2c_start(I2C_ADDR_WRITE);    if (mcp23018_status) goto out;
-    mcp23018_status = i2c_write(OLATA);             if (mcp23018_status) goto out;
-    mcp23018_status = i2c_write(0b11111111
-            & ~(ergodox_left_led_3<<LEFT_LED_3_SHIFT)
-          );                                        if (mcp23018_status) goto out;
-    mcp23018_status = i2c_write(0b11111111
-            & ~(ergodox_left_led_2<<LEFT_LED_2_SHIFT)
-            & ~(ergodox_left_led_1<<LEFT_LED_1_SHIFT)
-          );                                        if (mcp23018_status) goto out;
-
-out:
-    i2c_stop();
-    return mcp23018_status;
-}
-
diff --git a/keyboard/ergodox/ergodox.h b/keyboard/ergodox/ergodox.h
deleted file mode 100644
index 9d0691dfe2..0000000000
--- a/keyboard/ergodox/ergodox.h
+++ /dev/null
@@ -1,145 +0,0 @@
-#ifndef PLANCK_H
-#define PLANCK_H
-
-#include "matrix.h"
-#include "keymap_common.h"
-#include "backlight.h"
-#include <stddef.h>
-#include <stdint.h>
-#include <stdbool.h>
-#include <avr/io.h>
-#include "i2cmaster.h"
-#include <util/delay.h>
-
-#define CPU_PRESCALE(n) (CLKPR = 0x80, CLKPR = (n))
-#define CPU_16MHz       0x00
-
-// I2C aliases and register addresses (see "mcp23018.md")
-#define I2C_ADDR        0b0100000
-#define I2C_ADDR_WRITE  ( (I2C_ADDR<<1) | I2C_WRITE )
-#define I2C_ADDR_READ   ( (I2C_ADDR<<1) | I2C_READ  )
-#define IODIRA          0x00            // i/o direction register
-#define IODIRB          0x01
-#define GPPUA           0x0C            // GPIO pull-up resistor register
-#define GPPUB           0x0D
-#define GPIOA           0x12            // general purpose i/o port register (write modifies OLAT)
-#define GPIOB           0x13
-#define OLATA           0x14            // output latch register
-#define OLATB           0x15
-
-extern uint8_t mcp23018_status;
-
-void init_ergodox(void);
-void ergodox_blink_all_leds(void);
-uint8_t init_mcp23018(void);
-uint8_t ergodox_left_leds_update(void);
-
-#define LED_BRIGHTNESS_LO       31
-#define LED_BRIGHTNESS_HI       255
-
-#define LEFT_LED_1_SHIFT        7       // in MCP23018 port B
-#define LEFT_LED_2_SHIFT        6       // in MCP23018 port B
-#define LEFT_LED_3_SHIFT        7       // in MCP23018 port A
-
-extern bool ergodox_left_led_1;         // left top
-extern bool ergodox_left_led_2;         // left middle
-extern bool ergodox_left_led_3;         // left bottom
-
-inline void ergodox_board_led_on(void)      { DDRD |=  (1<<6); PORTD |=  (1<<6); }
-inline void ergodox_right_led_1_on(void)    { DDRB |=  (1<<5); PORTB |=  (1<<5); }
-inline void ergodox_right_led_2_on(void)    { DDRB |=  (1<<6); PORTB |=  (1<<6); }
-inline void ergodox_right_led_3_on(void)    { DDRB |=  (1<<7); PORTB |=  (1<<7); }
-inline void ergodox_left_led_1_on(void)     { ergodox_left_led_1 = 1; }
-inline void ergodox_left_led_2_on(void)     { ergodox_left_led_2 = 1; }
-inline void ergodox_left_led_3_on(void)     { ergodox_left_led_3 = 1; }
-
-inline void ergodox_board_led_off(void)     { DDRD &= ~(1<<6); PORTD &= ~(1<<6); }
-inline void ergodox_right_led_1_off(void)   { DDRB &= ~(1<<5); PORTB &= ~(1<<5); }
-inline void ergodox_right_led_2_off(void)   { DDRB &= ~(1<<6); PORTB &= ~(1<<6); }
-inline void ergodox_right_led_3_off(void)   { DDRB &= ~(1<<7); PORTB &= ~(1<<7); }
-inline void ergodox_left_led_1_off(void)    { ergodox_left_led_1 = 0; }
-inline void ergodox_left_led_2_off(void)    { ergodox_left_led_2 = 0; }
-inline void ergodox_left_led_3_off(void)    { ergodox_left_led_3 = 0; }
-
-inline void ergodox_led_all_on(void)
-{
-    ergodox_board_led_on();
-    ergodox_right_led_1_on();
-    ergodox_right_led_2_on();
-    ergodox_right_led_3_on();
-    ergodox_left_led_1_on();
-    ergodox_left_led_2_on();
-    ergodox_left_led_3_on();
-    ergodox_left_leds_update();
-}
-
-inline void ergodox_led_all_off(void)
-{
-    ergodox_board_led_off();
-    ergodox_right_led_1_off();
-    ergodox_right_led_2_off();
-    ergodox_right_led_3_off();
-    ergodox_left_led_1_off();
-    ergodox_left_led_2_off();
-    ergodox_left_led_3_off();
-    ergodox_left_leds_update();
-}
-
-inline void ergodox_right_led_1_set(uint8_t n)    { OCR1A = n; }
-inline void ergodox_right_led_2_set(uint8_t n)    { OCR1B = n; }
-inline void ergodox_right_led_3_set(uint8_t n)    { OCR1C = n; }
-
-inline void ergodox_led_all_set(uint8_t n)
-{
-    ergodox_right_led_1_set(n);
-    ergodox_right_led_2_set(n);
-    ergodox_right_led_3_set(n);
-}
-
-#define KEYMAP(                                                 \
-                                                                \
-    /* left hand, spatial positions */                          \
-    k00,k01,k02,k03,k04,k05,k06,                                \
-    k10,k11,k12,k13,k14,k15,k16,                                \
-    k20,k21,k22,k23,k24,k25,                                    \
-    k30,k31,k32,k33,k34,k35,k36,                                \
-    k40,k41,k42,k43,k44,                                        \
-                            k55,k56,                            \
-                                k54,                            \
-                        k53,k52,k51,                            \
-                                                                \
-    /* right hand, spatial positions */                         \
-        k07,k08,k09,k0A,k0B,k0C,k0D,                            \
-        k17,k18,k19,k1A,k1B,k1C,k1D,                            \
-            k28,k29,k2A,k2B,k2C,k2D,                            \
-        k37,k38,k39,k3A,k3B,k3C,k3D,                            \
-                k49,k4A,k4B,k4C,k4D,                            \
-    k57,k58,                                                    \
-    k59,                                                        \
-    k5C,k5B,k5A )                                               \
-                                                                \
-   /* matrix positions */                                       \
-   {                                                            \
-    { k00, k10, k20, k30, k40, KC_NO },   \
-    { k01, k11, k21, k31, k41, k51 },   \
-    { k02, k12, k22, k32, k42, k52 },   \
-    { k03, k13, k23, k33, k43, k53 },   \
-    { k04, k14, k24, k34, k44, k54 },   \
-    { k05, k15, k25, k35, KC_NO, k55 },   \
-    { k06, k16, KC_NO, k36, KC_NO, k56 },   \
-                                                                 \
-    { k07, k17, KC_NO, k37,KC_NO, k57 },   \
-    { k08, k18, k28, k38,KC_NO, k58 },   \
-    { k09, k19, k29, k39, k49, k59 },   \
-    { k0A, k1A, k2A, k3A, k4A, k5A },   \
-    { k0B, k1B, k2B, k3B, k4B, k5B },   \
-    { k0C, k1C, k2C, k3C, k4C, k5C },   \
-    { k0D, k1D, k2D, k3D, k4D, KC_NO }    \
-   }
-
-void * matrix_init_user(void);
-void * matrix_scan_user(void);
-
-
-
-#endif
\ No newline at end of file
diff --git a/keyboard/ergodox/i2cmaster.h b/keyboard/ergodox/i2cmaster.h
deleted file mode 100644
index 3917b9e6c0..0000000000
--- a/keyboard/ergodox/i2cmaster.h
+++ /dev/null
@@ -1,178 +0,0 @@
-#ifndef _I2CMASTER_H
-#define _I2CMASTER_H   1
-/************************************************************************* 
-* Title:    C include file for the I2C master interface 
-*           (i2cmaster.S or twimaster.c)
-* Author:   Peter Fleury <pfleury@gmx.ch>  http://jump.to/fleury
-* File:     $Id: i2cmaster.h,v 1.10 2005/03/06 22:39:57 Peter Exp $
-* Software: AVR-GCC 3.4.3 / avr-libc 1.2.3
-* Target:   any AVR device
-* Usage:    see Doxygen manual
-**************************************************************************/
-
-#ifdef DOXYGEN
-/**
- @defgroup pfleury_ic2master I2C Master library
- @code #include <i2cmaster.h> @endcode
-  
- @brief I2C (TWI) Master Software Library
-
- Basic routines for communicating with I2C slave devices. This single master 
- implementation is limited to one bus master on the I2C bus. 
-
- This I2c library is implemented as a compact assembler software implementation of the I2C protocol 
- which runs on any AVR (i2cmaster.S) and as a TWI hardware interface for all AVR with built-in TWI hardware (twimaster.c).
- Since the API for these two implementations is exactly the same, an application can be linked either against the
- software I2C implementation or the hardware I2C implementation.
-
- Use 4.7k pull-up resistor on the SDA and SCL pin.
- 
- Adapt the SCL and SDA port and pin definitions and eventually the delay routine in the module 
- i2cmaster.S to your target when using the software I2C implementation ! 
- 
- Adjust the  CPU clock frequence F_CPU in twimaster.c or in the Makfile when using the TWI hardware implementaion.
-
- @note 
-    The module i2cmaster.S is based on the Atmel Application Note AVR300, corrected and adapted 
-    to GNU assembler and AVR-GCC C call interface.
-    Replaced the incorrect quarter period delays found in AVR300 with 
-    half period delays. 
-    
- @author Peter Fleury pfleury@gmx.ch  http://jump.to/fleury
-
- @par API Usage Example
-  The following code shows typical usage of this library, see example test_i2cmaster.c
-
- @code
-
- #include <i2cmaster.h>
-
-
- #define Dev24C02  0xA2      // device address of EEPROM 24C02, see datasheet
-
- int main(void)
- {
-     unsigned char ret;
-
-     i2c_init();                             // initialize I2C library
-
-     // write 0x75 to EEPROM address 5 (Byte Write) 
-     i2c_start_wait(Dev24C02+I2C_WRITE);     // set device address and write mode
-     i2c_write(0x05);                        // write address = 5
-     i2c_write(0x75);                        // write value 0x75 to EEPROM
-     i2c_stop();                             // set stop conditon = release bus
-
-
-     // read previously written value back from EEPROM address 5 
-     i2c_start_wait(Dev24C02+I2C_WRITE);     // set device address and write mode
-
-     i2c_write(0x05);                        // write address = 5
-     i2c_rep_start(Dev24C02+I2C_READ);       // set device address and read mode
-
-     ret = i2c_readNak();                    // read one byte from EEPROM
-     i2c_stop();
-
-     for(;;);
- }
- @endcode
-
-*/
-#endif /* DOXYGEN */
-
-/**@{*/
-
-#if (__GNUC__ * 100 + __GNUC_MINOR__) < 304
-#error "This library requires AVR-GCC 3.4 or later, update to newer AVR-GCC compiler !"
-#endif
-
-#include <avr/io.h>
-
-/** defines the data direction (reading from I2C device) in i2c_start(),i2c_rep_start() */
-#define I2C_READ    1
-
-/** defines the data direction (writing to I2C device) in i2c_start(),i2c_rep_start() */
-#define I2C_WRITE   0
-
-
-/**
- @brief initialize the I2C master interace. Need to be called only once 
- @param  void
- @return none
- */
-extern void i2c_init(void);
-
-
-/** 
- @brief Terminates the data transfer and releases the I2C bus 
- @param void
- @return none
- */
-extern void i2c_stop(void);
-
-
-/** 
- @brief Issues a start condition and sends address and transfer direction 
-  
- @param    addr address and transfer direction of I2C device
- @retval   0   device accessible 
- @retval   1   failed to access device 
- */
-extern unsigned char i2c_start(unsigned char addr);
-
-
-/**
- @brief Issues a repeated start condition and sends address and transfer direction 
-
- @param   addr address and transfer direction of I2C device
- @retval  0 device accessible
- @retval  1 failed to access device
- */
-extern unsigned char i2c_rep_start(unsigned char addr);
-
-
-/**
- @brief Issues a start condition and sends address and transfer direction 
-   
- If device is busy, use ack polling to wait until device ready 
- @param    addr address and transfer direction of I2C device
- @return   none
- */
-extern void i2c_start_wait(unsigned char addr);
-
- 
-/**
- @brief Send one byte to I2C device
- @param    data  byte to be transfered
- @retval   0 write successful
- @retval   1 write failed
- */
-extern unsigned char i2c_write(unsigned char data);
-
-
-/**
- @brief    read one byte from the I2C device, request more data from device 
- @return   byte read from I2C device
- */
-extern unsigned char i2c_readAck(void);
-
-/**
- @brief    read one byte from the I2C device, read is followed by a stop condition 
- @return   byte read from I2C device
- */
-extern unsigned char i2c_readNak(void);
-
-/** 
- @brief    read one byte from the I2C device
- 
- Implemented as a macro, which calls either i2c_readAck or i2c_readNak
- 
- @param    ack 1 send ack, request more data from device<br>
-               0 send nak, read is followed by a stop condition 
- @return   byte read from I2C device
- */
-extern unsigned char i2c_read(unsigned char ack);
-#define i2c_read(ack)  (ack) ? i2c_readAck() : i2c_readNak(); 
-
-
-/**@}*/
-#endif
diff --git a/keyboard/ergodox/keymaps/keymap_cub.c b/keyboard/ergodox/keymaps/keymap_cub.c
deleted file mode 100644
index 6e6d0cd8df..0000000000
--- a/keyboard/ergodox/keymaps/keymap_cub.c
+++ /dev/null
@@ -1,595 +0,0 @@
-static const uint8_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
-    /*
-     * Keymap: Default Layer in QWERTY
-     *
-     * ,--------------------------------------------------.           ,--------------------------------------------------.
-     * |   ~    |   1  |   2  |   3  |   4  |   5  |   \  |           |   -  |   6  |   7  |   8  |   9  |   0  |   =    |
-     * |--------+------+------+------+------+-------------|           |------+------+------+------+------+------+--------|
-     * | Tab    |   Q  |   W  |   E  |   R  |   T  | ~L5  |           | ~L6  |   Y  |   U  |   I  |   O  |   P  |   [    |
-     * |--------+------+------+------+------+------|      |           |      |------+------+------+------+------+--------|
-     * | Tab/Shf|   A  |   S  |   D  |   F  |   G  |------|           |------|   H  |   J  |   K  |   L  |   ;  |   '    |
-     * |--------+------+------+------+------+------|  L0  |           | ~L7  |------+------+------+------+------+--------|
-     * | LCtrl  |   Z  |   X  |   C  |   V  |   B  |      |           |      |   N  |   M  |   ,  |   .  |   /  |   ]    |
-     * `--------+------+------+------+------+-------------'           `-------------+------+------+------+------+--------'
-     *   | ~L5  | ~L2  | Caps | LAlt | LGui |                                       |  Lft |  Up  |  Dn  | Rght | ~L6  |
-     *   `----------------------------------'                                       `----------------------------------'
-     *                                        ,-------------.       ,-------------.
-     *                                        | +L2  | Home |       | PgUp | Del  |
-     *                                 ,------|------|------|       |------+------+------.
-     *                                 |      |      |  End |       | PgDn |      |      |
-     *                                 | BkSp |  ESC |------|       |------| Enter| Space|
-     *                                 |      |      |  Spc |       | Ins  |      |      |
-     *                                 `--------------------'       `--------------------'
-     *
-     *
-     *
-     ****************************************************************************************************
-     *
-     * Under XOrg, I use my own mapping from QWERTY to "Workman for Programmers"
-     * See XOrg files in ./addons/ subdirectory.
-     *
-     * I have to do so, because of two things:
-     * 1) my native language is Russian, and XOrg keymap for it is based on QWERTY layout
-     * 2) I want to have non-standart shifted keys, like $ (as normal) and @ (as shifted), or _ and -
-     *
-     * And even if (2) could be solved using FN* keys (but there is limit in firmware for only 32 such
-     * keys), then (1) can't be solved at firmware level at all.
-     *
-     * So, I have to stick with QWERTY as my main layout + my own XOrg keyboard layout for English.
-     * But sometimes I have to input something when XOrg is not active - for example, in Linux console,
-     * or in firmware console (while debugging firmware), or when keyboard is connected to not my computer.
-     *
-     * For such cases I have Layer1 :)
-     * // hint: switch to Layer1 is only at Layer6
-     *
-     ****************************************************************************************************
-     *
-     *
-     *
-     * Keymap: Default Layer in Workman
-     *
-     * ,--------------------------------------------------.           ,--------------------------------------------------.
-     * |  ~     |   ;  |   !  |   #  |   {  |   }  |   '  |           |   ^  |   [  |   ]  |   *  |   (  |   )  |   =    |
-     * |--------+------+------+------+------+-------------|           |------+------+------+------+------+------+--------|
-     * | Tab    |   Q  |   D  |   R  |   W  |   B  |  NO  |           | ~L7  |   J  |   F  |   U  |   P  |   $  |   :    |
-     * |--------+------+------+------+------+------|      |           |      |------+------+------+------+------+--------|
-     * | Tab/Shf|   A  |   S  |   H  |   T  |   G  |------|           |------|   Y  |   N  |   E  |   O  |   I  |   -    |
-     * |--------+------+------+------+------+------| Home |           | End  |------+------+------+------+------+--------|
-     * |