Add Makefiles for TMK converters.

1 files changed, 98 insertions, 0 deletions

diff --git a/converter/ps2_usb/Makefile.tmk_rev2 b/converter/ps2_usb/Makefile.tmk_rev2
new file mode 100644
index 0000000000..bad958c36b
--- /dev/null
+++ b/converter/ps2_usb/Makefile.tmk_rev2
@@ -0,0 +1,98 @@
+# 
+# Makefile for TMK keyboard converter rev2
+#     https://github.com/tmk/keyboard_converter#pcb-rev2
+#
+# Target file name (without extension).
+TARGET = ps2_usb_tmk_rev2
+
+# Directory common source filess exist
+TOP_DIR = ../..
+
+# Directory keyboard dependent files exist
+TARGET_DIR = .
+
+# project specific files
+SRC =	keymap_common.c \
+	matrix.c \
+	led.c
+
+ifdef KEYMAP
+    SRC := keymap_$(KEYMAP).c $(SRC)
+else
+    SRC := keymap_plain.c $(SRC)
+endif
+
+CONFIG_H = config_tmk_rev2.h
+
+
+# MCU name
+MCU = atmega32u2
+
+# Processor frequency.
+#     This will define a symbol, F_CPU, in all source code files equal to the
+#     processor frequency in Hz. You can then use this symbol in your source code to
+#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
+#     automatically to create a 32-bit value in your source code.
+#
+#     This will be an integer division of F_USB below, as it is sourced by
+#     F_USB after it has run through any CPU prescalers. Note that this value
+#     does not *change* the processor frequency - it should merely be updated to
+#     reflect the processor speed set externally so that the code can use accurate
+#     software delays.
+F_CPU = 16000000
+
+
+#
+# LUFA specific
+#
+# Target architecture (see library "Board Types" documentation).
+ARCH = AVR8
+
+# Input clock frequency.
+#     This will define a symbol, F_USB, in all source code files equal to the
+#     input clock frequency (before any prescaling is performed) in Hz. This value may
+#     differ from F_CPU if prescaling is used on the latter, and is required as the
+#     raw input clock is fed directly to the PLL sections of the AVR for high speed
+#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
+#     at the end, this will be done automatically to create a 32-bit value in your
+#     source code.
+#
+#     If no clock division is performed on the input clock inside the AVR (via the
+#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
+F_USB = $(F_CPU)
+
+
+# Boot Section Size in *bytes*
+#   Teensy halfKay   512
+#   Teensy++ halfKay 1024
+#   Atmel DFU loader 4096
+#   LUFA bootloader  4096
+#   USBaspLoader     2048
+OPT_DEFS += -DBOOTLOADER_SIZE=4096
+
+
+# Build Options
+#   comment out to disable the options.
+#
+#BOOTMAGIC_ENABLE = yes	# Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE = yes	# Mouse keys(+4700)
+EXTRAKEY_ENABLE = yes	# Audio control and System control(+450)
+CONSOLE_ENABLE = yes	# Console for debug(+400)
+COMMAND_ENABLE = yes    # Commands for debug and configuration
+#NKRO_ENABLE = yes	# USB Nkey Rollover - not yet supported in LUFA
+
+
+# PS/2 Options
+#
+PS2_USE_INT = yes	# uses external interrupt for falling edge of PS/2 clock pin
+#PS2_USE_BUSYWAIT = yes	# uses primitive reference code
+
+
+# Search Path
+VPATH += $(TARGET_DIR)
+VPATH += $(TOP_DIR)
+
+include $(TOP_DIR)/protocol.mk
+include $(TOP_DIR)/protocol/lufa.mk
+include $(TOP_DIR)/common.mk
+include $(TOP_DIR)/rules.mk